Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › MASS AIR FLOW METER › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0492063 MASS AIR FLOW METER G

F33A-FTV ENGINE CONTROL  MASS AIR FLOW METER  INSPECTION  


PROCEDURE

Hide 22204 1.INSPECT INTAKE MASS AIR FLOW METER SUB-ASSEMBLY

a.
A334357C01
0.906,1.01 1.719,1.01 true 0.719,0.917 1.031,1.073 0.313,0.156 10 false *a
*a Intake Air Temperature Sensor (Thermistor)


Perform a visual check for any foreign matter on the temperature sensor (thermistor) of the intake mass air flow meter sub-assembly shown in the illustration.

OK:

There is no foreign matter.


If the result is not as specified, clean the intake air temperature sensor (thermistor).


b.
A487338C01
0.646,2.5 1.156,2.5 true 1.052,1.188 1.563,1.188 true 0.479,2.417 0.792,2.573 0.313,0.156 10 false *a 2.188,4.24 2.385,4.406 0.198,0.167 10 false *b 1.594,1.104 1.906,1.26 0.313,0.156 10 false *c
*a Air Blow Gun
*b 10 mm (0.394 in.)
*c Intake Air Temperature Sensor (Thermistor)


Clean the intake air temperature sensor (thermistor).

NOTICE:
·

Do not contact the intake mass air flow meter sub-assembly with the nozzle of the air duster.

·

Do not insert the nozzle of the air duster into the intake air temperature sensor (thermistor) area.



i.
A398469C01
0.125,0.125 0.365,0.302 0.24,0.177 10 false *a 1.313,0.24 1.552,0.406 0.24,0.167 10 false *b 1.563,0.573 1.792,0.74 0.229,0.167 10 false *c 0.688,0.906 0.927,1.083 0.24,0.177 10 false *d 0.677,1.708 0.917,1.885 0.24,0.177 10 false *e
*a Air Blow Duration
*b 3 to 6 Seconds
*c 1 Second
*d Air Blowing
*e Air Stopped


Using an air duster, clean the intake air temperature sensor (thermistor) area of the intake mass air flow meter sub-assembly by applying approximately 10 intermittent bursts of air to the intake air temperature sensor (thermistor) area at a pressure of approximately 392 to 981 kPa (4.0 to 10.0 kgf/cm2, 57 to 142 psi).

HINT:

After performing cleaning, check the intake air temperature sensor (thermistor) resistance.




c.
A334358C23
1.479,0.198 1.906,0.427 0.427,0.229 0.531,0.615 0.833,0.615 0.833,0.615 1.229,1.177 true 2.573,0.604 2.198,0.604 2.198,0.604 1.906,1.167 true 0.094,0.115 0.406,0.271 0.313,0.156 10 false *a 0.198,0.531 0.656,0.729 0.458,0.198 10 false THA 2.635,0.51 3.094,0.708 0.458,0.198 10 false E2G 1.563,0.25 2.021,0.448 0.458,0.198 10 false C25
*a Component without harness connected
(Intake Mass Air Flow Meter Sub-assembly)


Check the intake air temperature sensor (thermistor) resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C25)Location & Routing

Click Connector(C25)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Intake Mass Air Flow Meter Sub-Assembly LH

C25-4 (THA) - C25-2 (E2G) Always 0.47 to 19.3 kΩ


If the result is not as specified, replace the intake mass air flow meter sub-assembly.