Never perform work on fuel system components near any possible ignition sources.
Vaporized fuel could ignite, resulting in a serious accident.
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.
Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
The fuel tank sub-assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank sub-assembly may fall off the engine lifter.
FUEL SYSTEM
When disconnecting the fuel pressure fuel line, a large amount of diesel fuel will spill out. Follow these procedures.
Disconnect the fuel tube.
Drain any fuel remaining inside the fuel tube.
To protect the disconnected fuel tube from damage and contamination, cover it with a plastic bag.
Put a container under the connection.
Perform the following procedure when disconnecting the fuel tube connector (for quick type A).
Check for dirt or mud on the pipe and around the connector before disconnection. Clean if necessary.
|
Pinch |
|
Pull |
Pinch the connector and disconnect the connector and pipe.
If the connector and the pipe are stuck together, pinch the connector, and then push and pull the pipe to disconnect the pipe and pull it out.
| *a | O-Ring |
| *b | Connector |
| *c | Pipe |
| *d | Retainer |
| *e | Nylon Tube |
Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
Do not use any tools to separate the pipe and connector.
Do not forcefully bend or twist the nylon tube.
Check for foreign matter on the pipe seal surface. Clean if necessary.
Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.
Check for dirt or mud on the seal surface of the disconnected pipe. Clean if necessary.
To protect the disconnected pipe and connector from damage and contamination, cover them with a plastic bag.
Perform the following procedure when connecting the fuel tube connector (for quick type A).
Check that there is no damage or contamination in the connected part of the pipe.
|
Push |
Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a "click" sound. If the connection is tight, apply a small amount of fresh spindle oil or gasoline on the tip of the pipe.
| *a | O-Ring |
| *b | Connector |
| *c | Pipe |
| *d | Retainer |
| *e | Nylon Tube |
Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
After connecting the connectors and pipes, check if they are securely connected by trying to pull them apart.
|
Pull |
After having finished the connection, try to pull apart the pipe and connector to confirm that they are securely connected.
Check that there is no fuel leakage.
Perform the following procedure when disconnecting a fuel tube connector (for quick type B).
Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.
Check that there is no damage or foreign matter on the part of the fuel pipe that contacts the connector.
| *a | Retainer |
|
Push |
|
Down |
|
Pull |
Detach the 2 claws of the connector retainer. Push down on the connector and disconnect it from the pipe.
|
Pull |
|
Push |
If the connector and fuel pipe are stuck, pinch the fuel pipe by hand and push and pull the connector to disconnect it.
| *a | Retainer |
| *b | Fuel Pipe |
| *c | Nylon Tube |
| *d | Fuel Tube Connector |
| *e | O-Ring |
Check for any dirt and foreign matter contamination in the fuel pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the fuel pipe and connector.
Do not use any tools to separate the fuel pipe and connector.
Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
Check for any dirt and foreign matter on the fuel pipe seal surface. Clean if necessary.
Do not forcibly bend, twist or turn the nylon tube.
Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tube.
If the fuel pipe and connector are stuck together, pinch the tube between your fingers and turn it carefully to free it. Then disconnect the fuel tube.
Check for foreign matter on the seal surface of the disconnected fuel pipe. Clean it if necessary.
To protect the disconnected fuel pipe and connector from damage and foreign matter, cover them with a plastic bag.
Perform the following procedure when connecting a fuel tube connector (for quick type B).
Check for foreign matter on the fuel pipe and around the connector before connecting it. Clean it if necessary.
| *a | Retainer |
| *b | Claw |
|
Push |
|
Push in |
Align the axis of the connector with the axis of the fuel pipe. Push the fuel pipe into the connector, and then push up on the retainer.
Before connecting the tube connectors to the fuel pipes, check if there is any damage or foreign matter in the connectors.
|
Pull |
After connecting the fuel pipe and the connector, check that the fuel pipe and connector are securely connected by trying to pull them apart.
Perform the following procedure when disconnecting a fuel tube connector (for Quick Type C).
Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.
| *a | Retainer |
| *b | Fuel Pipe |
| *c | Fuel Tube Connector |
| *d | O-Ring |
| *e | Claw |
|
Push |
|
Pull out |
|
Pull off |
Disengage the 2 claws of the retainer. Pull out the retainer and disconnect the fuel tube connector from the fuel pipe.
Be sure to disconnect the fuel tube connector by hand.
If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.
Be sure to disconnect the fuel tube connector by hand.
Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has an O-ring that seals the pipe (fuel pipe).
Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.
Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.
Perform the following procedure when connecting a fuel tube connector (for Quick Type C).
Check that there is no damage or foreign matter on the connecting parts of the fuel lines.
| *a | Retainer |
| *b | Claw |
|
Push |
|
Push in |
Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean gasoline to the tip of the fuel pipe and reinsert it.
Connect the fuel lines and push in the retainer to engage the 2 claws. Check that the fuel pipe and fuel tube connector are securely connected by pulling on them.
Inspect for fuel leaks.
Perform the following procedure when disconnecting a fuel tube connector (for Quick Type D).
Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.
Check that there is no foreign matter around the fuel tube connector before disconnecting it. Clean it if necessary.
| *a | Retainer |
|
Retainer Holding Position |
|
Pull out |
While holding the retainer at the positions shown in the illustration, pull up the retainer to detach the lock claws.
| *a | Retainer |
| *b | Protective Tape |
If the lock claws of the retainer are difficult to detach, detach them using a screwdriver with its tip wrapped with protective tape.
| *a | Retainer |
| *b | O-ring |
| *c | Fuel Tube Connector |
| *d | Nylon Tube |
| *e | Fuel Pipe |
|
Retainer Holding Position |
|
Pull out |
|
Pull off |
Pull up the retainer while holding it at the positions shown in the illustration and pull off the fuel tube connector.
If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.
Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).
Do not bend, twist, pinch or kink the nylon tube.
Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.
Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.
Perform the following procedure when connecting a fuel tube connector (for Quick Type D).
Check that there is no damage or foreign matter on the connecting parts of the fuel lines.
| *a | Retainer |
|
Push |
|
Push in |
Align the fuel tube connector with the fuel pipe, push the fuel tube connector onto the fuel pipe, and then push in the retainer to secure the connection.
Confirm that the retainer makes a "click" sound when pushed.
If it is difficult to push the fuel tube connector onto the fuel pipe, apply a small amount of clean gasoline to the tip of the fuel pipe.
After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.
Inspect for fuel leaks.