Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484891 ECD SYSTEM(w/o DPF) D

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  INITIALIZATION  


INITIALIZATION PROCEDURE FOR DIESEL THROTTLE BODY ASSEMBLY, ELECTRIC EGR CONTROL VALVE ASSEMBLY AND TURBOCHARGER SUB-ASSEMBLY


HINT:

When the diesel throttle body assembly, electric EGR control valve assembly, turbocharger sub-assembly or turbocharger nozzle vane control actuator is replaced, perform initialization


a.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Turn the ignition switch to ON and wait for 10 seconds or more.



i-ART Learning Value Reset


NOTICE:
·

When the engine is started after the i-ART learned value is reset with the ignition switch ON, the value for "Injection Feedback Value" may indicate a malfunction momentarily. However, this is not a malfunction and is due to the i-ART learned value being reset. The value returns to normal once learning is begun.

·

When the battery cable is disconnected, reconnect the battery cable, turn the ignition switch to ON and wait 3 minutes or more before performing this procedure.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Powertrain / Engine / Utility / i-ART Learning Value Reset.

Powertrain > Engine > Utility
Tester Display
i-ART Learning Value Reset
50005 372 4610
·

3 minutes or more has elapsed after turning the ignition switch to ON and connecting the battery cable.

·

The engine is stopped.

·

The battery voltage is 8 V or more.



d.

Select the cylinder to be reset.


e.

Press "Next".

HINT:

The reset is performed automatically after "Next" is selected.



f.

If the reset fails, confirm the following conditions and perform the reset again.

i.

Turn the ignition switch to ON.


ii.

Turn the ignition switch off and wait for 30 seconds or more.


iii.

Turn the ignition switch to ON and wait 3 minutes or more.


iv.

The battery voltage is 8 V or more.



g.

When the screen indicating reset completion is displayed, push "Exit".



SWITCH SPECIFICATION INFORMATION


HINT:
·

Perform Switch Specification Information after replacing the ECM.

·

Perform Switch Specification Information using Utility of the GTS.

·

Perform the Health Check using the GTS and check that no DTC is output.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Switch Specification Information.

Powertrain > Engine > Utility
Tester Display
Switch Specification Information
50005 372 4551

e.

According to the prompts on the GTS screen, perform Switch Specification Information.


f.

Enter the following menus: Powertrain / Engine / Data List / Suspension Control Module Specification Information.

Powertrain > Engine > Data List
Tester Display
Suspension Control Module Specification Information
50003 372 1371

g.

Check that the Suspension Control Module Specification Information of the Data List displays a result other than Incomplete.

NOTICE:

If Incomplete is displayed, perform Switch Specification Information using Utility again.




CHANGE GRILLE SHUTTER CONTROL MODE AND/OR PERFORM INITIALIZATION


In the following situations, it is necessary to change the grille shutter control mode and/or initialize the grille shutter system.

Change Control Mode
(Normal Mode → Maintenance Mode)
Change Control Mode
(Maintenance Mode → Normal Mode)
Initialize
Before removing the radiator shutter assembly ○ - -
When the radiator shutter assembly has been replaced with a new one - ○ ○
After installing the radiator shutter assembly - ○ ○
Before troubleshooting ○ - -
After troubleshooting - ○ -

NOTICE:

In order to ensure safety, before performing troubleshooting or removing the radiator shutter assembly, change the grille shutter control mode to maintenance mode.


HINT:
·

When the grille shutter system is in maintenance mode, the grille shutter will not operate when operation signals are received.

·

When driving the vehicle to change the grille shutter control mode and/or perform initialization, make sure the grille shutter system is in maintenance mode. Initialization cannot be performed and the grille shutter control mode cannot be changed by driving the vehicle if the grille shutter system is in normal mode.



WHEN USING GTS
1.

Change the control mode to maintenance mode

(a)

Connect the GTS to the DLC3.

(b)

Turn the ignition switch to ON.

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine / Utility / Switch Grille Shutter Control Mode.

(e)

According to the display on the GTS, change the grille shutter control mode from normal mode to maintenance mode.


2.

Change the control mode to normal mode

(a)

Connect the GTS to the DLC3.

(b)

Turn the ignition switch to ON.

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine / Utility / Switch Grille Shutter Control Mode.

(e)

According to the display on the GTS, change the grille shutter control mode from maintenance mode to normal mode.


3.

Initialize

(a)

Connect the GTS to the DLC3.

(b)

Turn the ignition switch to ON.

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine / Utility / Grille Shutter Initialization / Initialization operation (Low Torque).

(e)

According to the display on the GTS, perform initialization.



WHEN DRIVING THE VEHICLE

Change the control mode to normal mode and initialize

HINT:

When changing the grille shutter control mode and/or performing initialization by driving the vehicle, the grille shutter control mode can only be changed and initialization can only be performed if the grille shutter system is in maintenance mode.


(a)

Start the engine.

(b)

Drive the vehicle at speed of 5 km/h (3 mph) or more. The grille shutter control mode will be changed and initialization (low torque) will be performed automatically when the vehicle speed exceeds 5 km/h (3 mph).