Each ECM terminal's standard voltage is shown in the table below.
In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".
Use the illustration above as a reference for the ECM terminals.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| B70-1 (BATT) - B70-10 (E1) | Battery (for measuring the battery voltage and for the ECM memory) | Always | 11 to 14 V |
| B70-9 (+B) - B70-10 (E1) | Power source of ECM | Ignition switch ON | 11 to 14 V |
| B70-35 (+B2) - B70-10 (E1) | |||
| B70-3 (MREL) - B70-10 (E1) | EFI MAIN NO. 1 relay operation signal | Ignition switch ON | 0 to 1.5 V |
| 3 seconds or more after ignition switch off | 11 to 14 V | ||
| B70-26 (IGR) - B70-10 (E1) | Ignition switch signal | Ignition switch ON | 11 to 14 V |
| B70-2 (IGP) - B70-10 (E1) | |||
| C138-19 (+BD1) - B70-10 (E1) | Power source of injector driver circuit | Ignition switch ON | 11 to 14 V |
| C138-38 (+BD2) - B70-10 (E1) | |||
| C138-18 (+BD3) - B70-10 (E1) | |||
| C138-37 (+BD4) - B70-10 (E1) | |||
| B70-44 (GREL) - B70-10 (E1) | GLOW NO. 1 relay operation signal | Cranking | 0 to 1.5 V |
| Idling (10 seconds or more after engine start) | 11 to 14 V | ||
| B70-43 (GRL2) - B70-10 (E1) | GLOW NO. 2 relay operation signal | Cranking | 0 to 1.5 V |
| Idling (10 seconds or more after engine start) | 11 to 14 V | ||
| B70-57 (VCPA) - B70-56 (EPA) | Power source of accelerator pedal position sensor (for VPA) | Ignition switch ON | 4.5 to 5.5 V |
| B70-55 (VPA) - B70-56 (EPA) | Accelerator pedal position sensor signal (for engine control) | Ignition switch ON, accelerator pedal fully released | 0.5 to 1.1 V |
| Accelerator pedal position sensor signal (for engine control) | Ignition switch ON, accelerator pedal fully depressed | 3.0 to 4.6 V | |
| B70-60 (VCP2) - B70-59 (EPA2) | Power source of accelerator pedal position sensor (for sensor malfunction detection) | Ignition switch ON | 4.5 to 5.5 V |
| B70-58 (VPA2) - B70-59 (EPA2) | Accelerator pedal position sensor signal (for sensor malfunction detection) | Ignition switch ON, accelerator pedal fully released | 0.9 to 2.3 V |
| Accelerator pedal position sensor signal (for sensor malfunction detection) | Ignition switch ON, accelerator pedal fully depressed | 3.4 to 5.0 V | |
| C139-54 (VCVG) - C139-53 (EVG) | Power source of mass air flow meter sub-assembly (for VG) | Ignition switch ON | 4.8 to 5.2 V |
| C139-43 (VG) - C139-53 (EVG) | Mass air flow meter sub-assembly signal | Idling | Pulse generation (See waveform 1) |
| C139-44 (THA) - C139-53 (EVG) | Intake air temperature sensor (built into mass air flow meter sub-assembly) | Idling, intake air temperature at 0 to 80°C (32 to 176°F) | 0.5 to 3.4 V |
| C138-76 (THIA) - B70-77 (ETHI) | Intake air temperature sensor (for intercooler outlet) | Idling, intake air temperature at 0 to 80°C (32 to 176°F) | 0.5 to 3.4 V |
| C138-102 (THCA) - C138-125 (ETCA) | Intake air temperature sensor (for intercooler inlet) | Idling, intake air temperature at 0 to 80°C (32 to 176°F) | 0.5 to 3.4 V |
| C138-78 (THW) - C138-79 (ETHW) | Engine coolant temperature sensor | Idling, engine coolant temperature at 60 to 120°C (140 to 248°F) | 0.2 to 1.0 V |
| C138-101 (THIW) - C138-124 (ETIW) | Engine coolant temperature sensor (for intercooler) | Engine warmed up, engine idling | 0.15 to 4.9 V |
| C138-36 (#1D+) - C138-17 (#1D-) | No. 1 Injector assembly signal | Idling | Pulse generation (See waveform 2) |
| C138-33 (#2D+) - C138-14 (#2D-) | No. 2 Injector assembly signal | ||
| C138-35 (#3D+) - C138-16 (#3D-) | No. 3 Injector assembly signal | ||
| C138-32 (#4D+) - C138-13 (#4D-) | No. 4 Injector assembly signal | ||
| C138-34 (#5D+) - C138-15 (#5D-) | No. 5 Injector assembly signal | ||
| C138-31 (#6D+) - C138-12 (#6D-) | No. 6 Injector assembly signal | ||
| C138-109 (VCNE) - C138-108 (NE-) | Power source of crankshaft position sensor (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| C138-62 (NE+) - C138-108 (NE-) | Crankshaft position sensor signal | Idling | Pulse generation (See waveform 3) |
| C138-86 (VCG) - C138-85 (G2-) | Power source of camshaft position sensor (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| C138-63 (G2+) - C138-85 (G2-) | Camshaft position sensor signal | Idling | Pulse generation (See waveform 4) |
| C138-106 (VCPM) - C138-129 (EPIM) | Power source of manifold absolute pressure sensor (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| C138-83 (PIM) - C138-129 (EPIM) | Manifold absolute pressure sensor | Negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg) applied | 0.1 to 0.7 V |
| Same as atmospheric pressure | 0.8 to 1.5 V | ||
| Positive pressure of 170 kPa (1275 mmHg, 50.2 in.Hg) applied | 1.6 to 2.3 V | ||
| B70-93 (VPBC) - B70-92 (EPBC) | Power source of manifold absolute pressure sensor (2nd turbocharger outlet side) (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| B70-70 (PBC) - B70-92 (EPBC) | Manifold absolute pressure sensor (2nd turbocharger outlet side) | Negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg) applied | 0.1 to 0.7 V |
| Same as atmospheric pressure | 0.8 to 1.5 V | ||
| Positive pressure of 170 kPa (1275 mmHg, 50.2 in.Hg) applied | 1.6 to 2.3 V | ||
| C139-52 (VIJ1) - C139-51 (EIJ1) | Power source of fuel pressure sensor (No. 1 injector assembly) | Ignition switch ON | 4.5 to 5.5 V |
| C139-50 (PIJ1) - C139-51 (EIJ1) | Fuel pressure sensor (No. 1 injector assembly) | Engine warmed up, engine idling | 1.4 to 1.7 V |
| C139-42 (VIJ2) - C139-41 (EIJ2) | Power source of fuel pressure sensor (No. 2 injector assembly) | Ignition switch ON | 4.5 to 5.5 V |
| C139-40 (PIJ2) - C139-41 (EIJ2) | Fuel pressure sensor (No. 2 injector assembly) | Engine warmed up, engine idling | 1.4 to 1.7 V |
| C139-32 (VIJ3) - C139-31 (EIJ3) | Power source of fuel pressure sensor (No. 3 injector assembly) | Ignition switch ON | 4.5 to 5.5 V |
| C139-30 (PIJ3) - C139-31 (EIJ3) | Fuel pressure sensor (No. 3 injector assembly) | Engine warmed up, engine idling | 1.4 to 1.7 V |
| C139-49 (VIJ4) - C139-48 (EIJ4) | Power source of fuel pressure sensor (No. 4 injector assembly) | Ignition switch ON | 4.5 to 5.5 V |
| C139-47 (PIJ4) - C139-48 (EIJ4) | Fuel pressure sensor (No. 4 injector assembly) | Engine warmed up, engine idling | 1.4 to 1.7 V |
| C139-39 (VIJ5) - C139-38 (EIJ5) | Power source of fuel pressure sensor (No. 5 injector assembly) | Ignition switch ON | 4.5 to 5.5 V |
| C139-37 (PIJ5) - C139-38 (EIJ5) | Fuel pressure sensor (No. 5 injector assembly) | Engine warmed up, engine idling | 1.4 to 1.7 V |
| C139-29 (VIJ6) - C139-28 (EIJ6) | Power source of fuel pressure sensor (No. 6 injector assembly) | Ignition switch ON | 4.5 to 5.5 V |
| C139-27 (PIJ6) - C139-28 (EIJ6) | Fuel pressure sensor (No. 6 injector assembly) | Engine warmed up, engine idling | 1.4 to 1.7 V |
| C138-29 (PCV+) - C138-30 (PCV-) | Pre-stroke control valve (bank 1) operation signal | Idling | Pulse generation (See waveform 5) |
| C138-8 (PV2+) - C138-9 (PV2-) | Pre-stroke control valve (bank 2) operation signal | Idling | Pulse generation (See waveform 5) |
| C138-10 (PRV+) - C138-11 (PRV-) | Pressure discharge valve signal | Ignition switch turned off after idling | Pulse generation |
| C138-6 (VNM+) - B70-10 (E1) | Variable vane DC motor signal (turbocharger nozzle vane control actuator bank1) | Idling | Pulse generation |
| C138-25 (VNM-) - B70-10 (E1) | |||
| C138-7 (VN2+) - B70-10 (E1) | Variable vane DC motor signal (turbocharger nozzle vane control actuator bank2) | Idling | Pulse generation |
| C138-26 (VN2-) - B70-10 (E1) | |||
| C138-95 (VNVC) - C138-118 (VNE2) | Power source of nozzle vane position sensor (turbocharger nozzle vane control actuator bank1) | Ignition switch ON | 4.7 to 5.3 V |
| C138-72 (VNA) - C138-118 (VNE2) | Nozzle vane position sensor signal (turbocharger nozzle vane control actuator bank1) | Ignition switch ON | 2.3 to 2.7 V |
| C138-112 (VNC2) - C138-111 (VE2) | Power source of nozzle vane position sensor (turbocharger nozzle vane control actuator bank2) | Ignition switch ON | 4.7 to 5.3 V |
| C138-65 (VNA2) - C138-111 (VE2) | Nozzle vane position sensor signal (turbocharger nozzle vane control actuator bank2) | Ignition switch ON | 2.3 to 2.7 V |
| C138-116 (VCVL) - C138-115 (EVLU) | Power source of throttle position sensor | Ignition switch ON | 4.5 to 5.5 V |
| C138-69 (VLU) - C138-115 (EVLU) | Throttle position sensor signal | Ignition switch ON, throttle valve fully closed |
0.4 to 1.0 V |
| Ignition switch ON, throttle valve fully opened |
3.6 to 4.2 V | ||
| C138-5 (M+) - B70-10 (E1) | Diesel throttle duty signal | Engine warmed up, racing engine | Pulse generation (See waveform 6) |
| C138-24 (M-) - B70-10 (E1) | Diesel throttle duty signal | Engine warmed up, racing engine | Pulse generation (See waveform 7) |
| C138-114 (VCEG) - C138-113 (EEGL) | Power source of EGR valve position sensor | Ignition switch ON | 4.5 to 5.5 V |
| C138-67 (EGRA) - C138-113 (EEGL) | EGR valve position sensor | Ignition switch ON | 0.6 to 1.4 V |
| C138-3 (EGM+) - B70-10 (E1) | EGR valve duty signal | Engine warmed up, idling | Pulse generation (See waveform 8) |
| C138-22 (EGM-) - B70-10 (E1) | EGR valve duty signal | Engine warmed up, idling | Pulse generation (See waveform 9) |
| C138-91 (VCEC) - C138-90 (EECB) | Power source of No. 2 EGR valve assembly (EGR cooler bypass valve) | Ignition switch ON | 4.5 to 5.5 V |
| C138-68 (ECBA) - C138-90 (EECB) | No. 2 EGR valve assembly (EGR cooler bypass valve) position sensor | Ignition switch ON | 0.6 to 1.4 V |
| C138-4 (ECM+) - B70-10 (E1) | No. 2 EGR valve assembly (EGR cooler bypass valve) motor signal | Engine warmed up, idling | Pulse generation (See waveform 16) |
| C138-23 (ECM-) - B70-10 (E1) | No. 2 EGR valve assembly (EGR cooler bypass valve) motor signal | Engine warmed up, idling | Pulse generation (See waveform 17) |
| C138-104 (THGO) - C138-127 (ETGO) | EGR gas temperature sensor | Engine warmed up, idling | 0.2 to 4.95 V |
| C138-119 (VCPE) - C138-120 (EPEO) | Power source of oil pressure sensor | Ignition switch ON | 4.5 to 5.5 V |
| C138-74 (PEO) - C138-120 (EPEO) | Oil pressure sensor | Engine warmed up, engine idling | 0.8 to 1.1 V |
| B70-31 (NEO) - B70-10 (E1) | Crankshaft position sensor signal sent to certification ECU (smart key ECU assembly) | Engine warmed up, idling | Pulse generation (See waveform 10) |
| C139-2 (CFDS) - B70-10 (E1) | Fan control solenoid operation signal | Fan control solenoid operating | Pulse generation |
| C138-96 (VCF) - C138-97 (ECF) | Power source of fan speed sensor (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| C138-73 (NCF) - C138-97 (ECF) | fan speed sensor signal | Idling | Pulse generation |
| C138-49 (ACV) - B70-10 (E1) | No. 2 vacuum switching valve assembly (for intake air control valve) | No. 2 vacuum switching valve assembly (for intake air control valve) off | 11 to 14 V |
| No. 2 vacuum switching valve assembly (for intake air control valve) on | 0 to 1.5 V | ||
| C138-45 (ECV) - B70-10 (E1) | No. 1 vacuum switching valve assembly (for exhaust control valve) | No. 1 vacuum switching valve assembly (for exhaust control valve) off | 11 to 14 V |
| No. 1 vacuum switching valve assembly (for exhaust control valve) on | 0 to 1.5 V | ||
| C139-7 (ABV) - B70-10 (E1) | Air by-pass valve assembly operation signal | Air by-pass valve assembly not operating | 11 to 14 V |
| Air by-pass valve assembly operating | 0 to 1.5 V | ||
| B70-50 (THPT) - B70-49 (ETPT) | Fuel filter temperature sensor signal | Ignition switch ON | 0.12 to 4.88 V |
| B70-16 (FLH) - B70-10 (E1) | FUEL FIL relay operation signal | Fuel filter heater not operating | 0 to 1.5 V |
| Fuel filter heater operating | 11 to 14 V | ||
| B70-21 (ST1-) - B70-10 (E1) | Stop light switch assembly signal (opposite to STP) |
Ignition switch ON, brake pedal depressed | 0 to 1.5 V |
| Ignition switch ON, brake pedal released | 7.5 to 14 V | ||
| B70-22 (STP) - B70-10 (E1) | Stop light switch assembly signal | Brake pedal depressed | 7.5 to 14 V |
| Brake pedal released | 0 to 1.5 V | ||
| B70-30 (NSW) - B70-10 (E1) | Park/Neutral position switch assembly signal | Ignition switch ON, shift lever not in P or N | 11 to 14 V |
| Ignition switch ON, shift lever in P or N | Below 1.0 V | ||
| B70-25 (STA) - B70-10 (E1) | Starter signal | Cranking | 6.0 V or higher |
| B70-15 (SPD) - B70-10 (E1) | Speed signal from combination meter assembly | Driving at vehicle speed of 20 km/h (12 mph) | Pulse generation (See waveform 11) |
| B70-34 (AC1) - B70-53 (E01) | A/C signal | A/C switch on | 0 to 1.5 V |
| A/C switch off | 11 to 14 V | ||
| B70-33 (ACT) - B70-53 (E01) | A/C signal | Ignition switch ON | 11 to 14 V |
| A/C cut control on | 0 to 3 V | ||
| B70-37 (IWPO) - B70-10 (E1) | Electric water pump assembly signal | Electric water pump assembly operating | Pulse generation |
| B70-38 (IWPI) - B70-10 (E1) | Electric water pump assembly signal | Electric water pump assembly operating | Pulse generation |
| B70-5 (CANU) - B70-10 (E1) | CAN communication line | Ignition switch ON | Pulse generation (See waveform 12) |
| B70-6 (CAND) - B70-10 (E1) | CAN communication line | Ignition switch ON | Pulse generation (See waveform 13) |
| B70-7 (CANH) - B70-10 (E1) | CAN communication line | Ignition switch ON | Pulse generation (See waveform 12) |
| B70-8 (CANL) - B70-10 (E1) | CAN communication line | Ignition switch ON | Pulse generation (See waveform 13) |
| B70-17 (CACH) - B70-10 (E1) | CAN communication line | Ignition switch ON | Pulse generation (See waveform 12) |
| B70-18 (CACL) - B70-10 (E1) | CAN communication line | Ignition switch ON | Pulse generation (See waveform 13) |
| C139-17 (CAN+) - B70-10 (E1) | CAN communication line | Ignition switch ON | Pulse generation (See waveform 12) |
| C139-18 (CAN-) - B70-10 (E1) | CAN communication line | Ignition switch ON | Pulse generation (See waveform 13) |
| B70-13 (LIN) - B70-10 (E1) | LIN communication line | Ignition switch ON | Pulse generation (See waveform 14) |
| C139-23 (CINJ) - B70-10 (E1) | INJ communication line | Engine warmed up, idling | Pulse generation (See waveform 15) |
| B70-53 (E01) - Body ground | Ground circuit of ECM | Always | Below 1 Ω |
| B70-36 (E02) - Body ground | Ground circuit of ECM | Always | Below 1 Ω |
| B70-10 (E1) - Body ground | Ground circuit of ECM | Always | Below 1 Ω |
| B70-47 (EC) - Body ground | Ground circuit of ECM | Always | Below 1 Ω |
| B70-54 (E1D1) - Body ground | Ground circuit of ECM | Always | Below 1 Ω |
WAVEFORM 1
| ECM Terminal Name | Between VG and EVG |
| Tester Range | 1 V/DIV., 100 μsec./DIV. |
| Condition | Ignition switch ON |
WAVEFORM 2
| ECM Terminal Name | Between #1D+ and #1D- Between #2D+ and #2D- Between #3D+ and #3D- Between #4D+ and #4D- Between #5D+ and #5D- Between #6D+ and #6D- |
| Tester Range | 10 V/DIV., 1 ms./DIV. |
| Condition | Idling with warm engine |
The waveform varies depending on the injector injection.
WAVEFORM 3
| ECM Terminal Name | Between NE+ and NE- |
| Tester Range | 2 V/DIV., 10 ms./DIV. |
| Condition | Idling with warm engine |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 4
| ECM Terminal Name | Between G2+ and G2- |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine |
The waveform varies depending on the engine speed.
WAVEFORM 5
| ECM Terminal Name | Between PCV+ and PCV- Between PV2+ and PV2- |
| Tester Range | 10 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine |
The waveform varies depending on pre-stroke control valve operation.
WAVEFORM 6
| ECM Terminal Name | Between M+ and E1 |
| Tester Range | 5 V/DIV., 1 ms./DIV. |
| Condition | Idling with warm engine |
The duty ratio varies depending on the throttle actuator operation.
WAVEFORM 7
| ECM Terminal Name | Between M- and E1 |
| Tester Range | 5 V/DIV., 1 ms./DIV. |
| Condition | Idling with warm engine |
The duty ratio varies depending on the throttle actuator operation.
WAVEFORM 8
| ECM Terminal Name | Between EGM+ and E1 |
| Tester Range | 5 V/DIV., 1 ms./DIV. |
| Condition | Idling with warm engine |
The duty ratio varies depending on the EGR valve operation.
WAVEFORM 9
| ECM Terminal Name | Between EGM- and E1 |
| Tester Range | 5 V/DIV., 1 ms./DIV. |
| Condition | Idling with warm engine |
The duty ratio varies depending on the EGR valve operation.
WAVEFORM 10
| ECM Terminal Name | Between NEO and E1 |
| Tester Range | 1 V/DIV., 2 ms./DIV. |
| Condition | Idling with warm engine |
WAVEFORM 11
| ECM Terminal Name | Between SPD and E1 |
| Tester Range | 2 V/DIV., 20 ms./DIV. |
| Condition | Driving at vehicle speed of 20 km/h (12 mph) |
The wavelength becomes shorter as the vehicle speed increases.
WAVEFORM 12
| ECM Terminal Name | Between CANU and E1 Between CANH and E1 Between CACH and E1 Between CAN+ and E1 |
| Tester Range | 1 V/DIV., 10 ms./DIV. |
| Condition | Engine stopped, ignition switch ON |
The waveform varies depending on the CAN communication signal.
WAVEFORM 13
| ECM Terminal Name | Between CAND and E1 Between CANL and E1 Between CACL and E1 Between CAN- and E1 |
| Tester Range | 1 V/DIV., 10 ms./DIV. |
| Condition | Engine stopped, ignition switch ON |
The waveform varies depending on the CAN communication signal.
WAVEFORM 14
| ECM Terminal Name | Between LIN and E1 |
| Tester Range | 2 V/DIV., 10 ms./DIV. |
| Condition | Engine stopped, ignition switch ON |
The waveform varies depending on the LIN communication signal.
WAVEFORM 15
| ECM Terminal Name | Between CINJ and E1 |
| Tester Range | 2 V/DIV., 10 ms./DIV. |
| Condition | Idling with warm engine |
The waveform is output every 250 msec.
WAVEFORM 16
| ECM Terminal Name | Between ECM+ and E1 |
| Tester Range | 5 V/DIV., 1 ms./DIV. |
| Condition | Idling with warm engine |
The duty ratio varies depending on the EGR cooler bypass valve operation.
WAVEFORM 17
| ECM Terminal Name | Between ECM- and E1 |
| Tester Range | 5 V/DIV., 1 ms./DIV. |
| Condition | Idling with warm engine |
The duty ratio varies depending on the EGR cooler bypass valve operation.