Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Headlight ECU) › from 2022.11
RM38G0E _59 Vehicle Exterior _100649 LIGHTING (EXT) _0468731 LIGHTING SYSTEM(w/ Headlight ECU) C

LIGHTING (EXT)  LIGHTING SYSTEM(w/ Headlight ECU)  B242E14  IG Circuit Short to Ground or Open  


DESCRIPTION

The headlight ECU sub-assembly operates using the power source voltage input from the IGR terminal and ECUB terminal.

The IGR terminal power source voltage is supplied by turning the IGR NO. 1 relay to ON.

The headlight ECU sub-assembly receives ignition switch ON signals from the main body ECU (multiplex network body ECU) via CAN communication, compares the ignition switch ON signal and the power source voltage supply condition of the IGR terminal and monitors the result.

Headlight Control
DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B242E14 IG Circuit Short to Ground or Open
Detection condition:

The ignition switch is ON.


Malfunction status:

When the IGR terminal power source voltage is 0 V (ignition switch off), ignition switch ON signals from the main body ECU (multiplex network body ECU) via CAN communication are continuously received


Malfunction duration:

10 seconds or more


for LHD
·

Headlight ECU sub-assembly LH

·

Harness or connector


for RHD
·

Headlight ECU sub-assembly LH

·

Headlight cord LH

·

Harness or connector


Headlight Control A

Headlight Control (Sub)
DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B242E14 IG Circuit Short to Ground or Open
Detection condition:

The ignition switch is ON.


Malfunction status:

When the IGR terminal power source voltage is 0 V (ignition switch off), ignition switch ON signals from the main body ECU (multiplex network body ECU) via CAN communication are continuously received


Malfunction duration:

10 seconds or more


for LHD
·

Headlight ECU sub-assembly RH

·

Harness or connector


for RHD
·

Headlight ECU sub-assembly RH

·

Headlight cord RH

·

Harness or connector


Headlight Control (Sub) A

WIRING DIAGRAM

for LHD


E370857E42
0.229,0.708 2.219,0.906 1.99,0.198 10 false from IGR NO. 3 Relay 2.438,0.885 3.5,1.167 1.063,0.281 10 false ENG-IGR NO. 3 4.667,1.885 5.104,2.125 0.438,0.24 10 false B4 4.656,4.073 5.063,4.313 0.406,0.24 10 false B7 4.667,2.052 7.073,2.406 2.406,0.354 10 false Headlight ECU Sub-assembly LH 4.656,4.24 7.115,4.479 2.458,0.24 10 false Headlight ECU Sub-assembly RH 4.99,0.604 5.198,0.854 0.208,0.25 10 false 6 5,2.833 5.208,3.083 0.208,0.25 10 false 6 5.188,0.729 5.51,0.969 0.323,0.24 10 false IGR 5.188,2.948 5.51,3.177 0.323,0.229 10 false IGR 4.948,1.25 5.156,1.5 0.208,0.25 10 false 12 4.938,3.469 5.146,3.719 0.208,0.25 10 false 12 5.177,1.354 5.552,1.615 0.375,0.26 10 false GND 5.177,3.563 5.552,3.823 0.375,0.26 10 false GND


for RHD


E483597E02
0.26,0.469 2.094,1.188 1.833,0.719 10 false from IGR NO.3 Relay 2.24,0.604 3.302,0.885 1.063,0.281 10 false ENG-IGR NO.3 5.625,1.771 6.823,2.406 1.198,0.635 10 false Headlight ECU Sub-assembly LH 5.573,4.135 6.781,4.74 1.208,0.604 10 false Headlight ECU Sub-assembly RH 5.5,0.26 5.698,0.521 0.198,0.26 10 false 6 5.5,2.615 5.708,2.865 0.208,0.25 10 false 6 4.531,0.333 4.938,0.542 0.406,0.208 10 false IGR 5.833,2.792 6.281,3.021 0.448,0.229 10 false IGR 5.448,0.865 5.656,1.115 0.208,0.25 10 false 12 5.458,3.229 5.667,3.479 0.208,0.25 10 false 12 4.49,0.958 4.865,1.219 0.375,0.26 10 false GND 5.792,3.417 6.167,3.677 0.375,0.26 10 false GND 5.833,1.063 6.208,1.323 0.375,0.26 10 false GND 5.833,0.448 6.24,0.656 0.406,0.208 10 false IGR 4.146,0.24 4.354,0.49 0.208,0.25 10 false 2 4.146,0.865 4.354,1.115 0.208,0.25 10 false 1 4.063,1.083 4.5,1.323 0.438,0.24 10 false BB7 4.052,0.448 4.49,0.688 0.438,0.24 10 false BB6 4.073,2.802 4.51,3.042 0.438,0.24 10 false BB8 4.052,3.427 4.49,3.667 0.438,0.24 10 false BB9 4.188,2.604 4.396,2.854 0.208,0.25 10 false 2 4.167,3.208 4.375,3.458 0.208,0.25 10 false 1 4.49,3.292 4.865,3.552 0.375,0.26 10 false GND 4.479,2.698 4.885,2.906 0.406,0.208 10 false IGR 5.406,0.448 5.844,0.688 0.438,0.24 10 false B88 5.417,1.073 5.854,1.313 0.438,0.24 10 false B88 5.396,2.802 5.833,3.042 0.438,0.24 10 false B89 5.406,3.427 5.844,3.667 0.438,0.24 10 false B89 4.417,1.479 5.688,2.063 1.271,0.583 10 false Headlight Cord LH 4.365,3.813 5.635,4.396 1.271,0.583 10 false Headlight Cord RH


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Headlight ECU)>REGISTRATION

·

When replacing the headlight ECU sub-assembly LH, always replace it with a new one. If a headlight ECU sub-assembly LH which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242E14 is not output A
B242E14 is output B



Post-procedure1

d.

None



A

3.CLEAR DTC

B

11.CHECK VEHICLE TYPE
3.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control (Sub) > Clear DTCs
50002 463

Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control (Sub) > Trouble Codes
50001 463
Result:
Result Proceed to
B242E14 is not output A
B242E14 is output B



Post-procedure1

d.

None



A

B

5.CHECK VEHICLE TYPE
5.CHECK VEHICLE TYPE
Result:
Result Proceed to
for LHD A
for RHD B



A

6.CHECK HARNESS AND CONNECTOR (IGR TERMINAL VOLTAGE)

B

8.INSPECT HEADLIGHT CORD RH
6.CHECK HARNESS AND CONNECTOR (IGR TERMINAL VOLTAGE)

Pre-procedure1

a.

Disconnect the B7 headlight ECU sub-assembly RH connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(B7)Location & Routing

Click Connector(B7)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly RH

B7-6 (IGR) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY RH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY RH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B7)Location & Routing

Click Connector(B7)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly RH

B7-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT HEADLIGHT CORD RH

Pre-procedure1

a.

Remove the headlight cord RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

E483590C09
6.01,0.594 6.427,0.917 0.417,0.323 4.333,0.427 4.75,0.75 0.417,0.323 1.698,0.333 2.115,0.656 0.417,0.323 1.167,2.156 1.115,1.635 true 6.292,2.01 6.271,1.448 true 2.573,2.208 2.208,1.542 true 5.031,2.094 4.813,1.281 true 0.26,0.188 0.573,0.385 0.313,0.198 10 false *a 3.729,0.229 4.042,0.427 0.313,0.198 10 false *a 5.813,0.26 6.125,0.458 0.313,0.198 10 false *a 1.802,0.427 2.115,0.625 0.313,0.198 10 false B89 6.104,0.667 6.604,1.01 0.5,0.344 10 false BB9 4.427,0.521 4.927,0.865 0.5,0.344 10 false BB8 0.938,2.188 1.813,2.542 0.875,0.354 10 false GND 6.167,2.031 7.042,2.385 0.875,0.354 10 false GND 2.531,2.26 3.406,2.615 0.875,0.354 10 false IGR 4.896,2.188 5.771,2.542 0.875,0.354 10 false IGR
*a Component without harness connected
(Headlight Cord RH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(BB8,B89,BB9)Location & Routing

Click Connector(BB8)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Engine Room Main Wire and Lamp Wire

Click Connector(B89)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly RH

Click Connector(BB9)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Engine Room Main Wire and Lamp Wire

BB8-2 (ECUB) - B89-6 (IGR) Always Below 1 Ω
BB9-1 (GND) - B89-12 (GND) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

9.CHECK HARNESS AND CONNECTOR (IGR TERMINAL VOLTAGE)

NG

9.CHECK HARNESS AND CONNECTOR (IGR TERMINAL VOLTAGE)

Pre-procedure1

a.

Connect the BB8 and BB9 headlight cord RH connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(B89)Location & Routing

Click Connector(B89)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly RH

B89-6 (IGR) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

10.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY RH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY RH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B89)Location & Routing

Click Connector(B89)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly RH

B89-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK VEHICLE TYPE
Result:
Result Proceed to
for LHD A
for RHD B



A

12.CHECK HARNESS AND CONNECTOR (IGR TERMINAL VOLTAGE)

B

14.INSPECT HEADLIGHT CORD LH
12.CHECK HARNESS AND CONNECTOR (IGR TERMINAL VOLTAGE)

Pre-procedure1

a.

Disconnect the B4 headlight ECU sub-assembly LH connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(B4)Location & Routing

Click Connector(B4)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly LH

B4-6 (IGR) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

13.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B4)Location & Routing

Click Connector(B4)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly LH

B4-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT HEADLIGHT CORD LH

Pre-procedure1

a.

Remove the headlight cord LH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

E483590C10
6.021,0.594 6.438,0.917 0.417,0.323 4.344,0.427 4.76,0.75 0.417,0.323 1.698,0.333 2.115,0.656 0.417,0.323 1.115,2.125 1.094,1.604 true 6.292,2.01 6.271,1.448 true 2.563,2.188 2.198,1.521 true 5,2.052 4.792,1.302 true 0.26,0.188 0.573,0.385 0.313,0.198 10 false *a 3.729,0.229 4.042,0.427 0.313,0.198 10 false *a 5.813,0.26 6.125,0.458 0.313,0.198 10 false *a 1.781,0.427 2.094,0.625 0.313,0.198 10 false B88 4.427,0.5 4.927,0.844 0.5,0.344 10 false BB6 6.115,0.677 6.615,1.021 0.5,0.344 10 false BB7 0.938,2.188 1.813,2.542 0.875,0.354 10 false GND 6.167,2.031 7.042,2.385 0.875,0.354 10 false GND 2.625,2.219 3.5,2.573 0.875,0.354 10 false IGR 4.948,2.125 5.823,2.479 0.875,0.354 10 false IGR
*a Component without harness connected
(Headlight Cord LH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(BB6,B88,BB7)Location & Routing

Click Connector(BB6)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Engine Room Main Wire and No. 2 Lamp Wire

Click Connector(B88)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly LH

Click Connector(BB7)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Engine Room Main Wire and No. 2 Lamp Wire

BB6-2 (IGR) - B88-6 (IGR) Always Below 1 Ω
BB7-1 (GND) - B88-12 (GND) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

15.CHECK HARNESS AND CONNECTOR (IGR TERMINAL VOLTAGE)

NG

15.CHECK HARNESS AND CONNECTOR (IGR TERMINAL VOLTAGE)

Pre-procedure1

a.

Connect the BB6 and BB7 headlight cord LH connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(B88)Location & Routing

Click Connector(B88)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly LH

B88-6 (IGR) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

16.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B88)Location & Routing

Click Connector(B88)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly LH

B88-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR