Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Headlight ECU) › from 2022.11
RM38G0E _59 Vehicle Exterior _100649 LIGHTING (EXT) _0468731 LIGHTING SYSTEM(w/ Headlight ECU) C

LIGHTING (EXT)  LIGHTING SYSTEM(w/ Headlight ECU)  B242487  Leveling Motor LH Missing Message  B242587  Leveling Motor RH Missing Message  


DESCRIPTION

*: w/ Adaptive High Beam System


The headlight ECU sub-assembly sends the automatic headlight beam leveling control signal to the headlight leveling motor via LIN communication. The headlight leveling motor operates according to the power supply and automatic headlight beam leveling control signals received from the headlight ECU sub-assembly and sends its operating state to the headlight ECU sub-assembly via LIN communication.

The headlight ECU sub-assembly sends the adaptive high beam system control signal to the light control LED ECU via LIN communication.*

The light control LED ECU receives the power supply and control signals from the headlight ECU sub-assembly and controls the LED array and LED array fan, and sends its operating state to the headlight ECU sub-assembly via LIN communication.*

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B242487 Leveling Motor LH Missing Message
Detection condition:

The ignition switch is ON.


Malfunction status:

LIN communication is lost with headlight leveling motor LH


Malfunction duration:

10 seconds or more


·

Headlight unit assembly LH

·

Headlight leveling motor LH

·

Headlight ECU sub-assembly LH


Headlight Control A
B242587 Leveling Motor RH Missing Message
Detection condition:

The ignition switch is ON.


Malfunction status:

LIN communication is lost with headlight leveling motor RH


Malfunction duration:

10 seconds or more


for LHD
·

Harness or connector

·

Headlight unit assembly RH

·

Headlight leveling motor RH

·

headlight ECU sub-assembly RH

·

Headlight ECU sub-assembly LH


for RHD
·

Harness or connector

·

Headlight unit assembly RH

·

Headlight leveling motor RH

·

headlight ECU sub-assembly RH

·

Headlight ECU sub-assembly LH

·

Headlight cord LH

·

Headlight cord RH


Headlight Control A

w/ Adaptive High Beam System
Output DTC Suspected Area (Malfunction Status)
B242487 B242587 B244087 B244187

○: DTC is output

-: DTC is not output

○ ○ ○ ○ LIN communication circuit (short)
Headlight ECU sub-assembly LH (Internal malfunction)
Headlight ECU sub-assembly RH (Internal malfunction)
○ - ○ - Headlight ECU sub-assembly LH (Internal malfunction)
- ○ - ○ LIN communication circuit (open)
Headlight ECU sub-assembly RH (Internal malfunction)
Headlight ECU sub-assembly LH (Internal malfunction)
○ - - - Headlight leveling motor LH power supply system abnormal
Headlight leveling motor LH (Internal malfunction)
Harness open circuit (headlight ECU sub-assembly LH to headlight leveling motor LH)
Headlight ECU sub-assembly LH (Internal malfunction)
- ○ - - Headlight leveling motor RH power supply abnormal
Headlight leveling motor RH (Internal malfunction)
Harness open circuit (headlight ECU sub-assembly RH to headlight leveling motor RH)
Headlight ECU sub-assembly RH (Internal malfunction)
- - ○ - Light control LED ECU LH power supply system abnormal
Light control LED ECU LH (Internal malfunction)
Harness open circuit (headlight ECU sub-assembly LH to light control LED ECU LH)
Headlight ECU sub-assembly LH (Internal malfunction)
- - - ○ Light control LED ECU RH power supply system abnormal
Light control LED ECU RH (Internal malfunction)
Harness open circuit (headlight ECU sub-assembly RH to light control LED ECU RH)
Headlight ECU sub-assembly RH (Internal malfunction)

w/o Adaptive High Beam System
Output DTC Suspected Area (Malfunction Status)
B242487 B242587

○: DTC is output

-: DTC is not output

○ ○ LIN communication circuit (short)
Headlight ECU sub-assembly LH (Internal malfunction)
Headlight ECU sub-assembly RH (Internal malfunction)
○ - Headlight leveling motor LH power supply system abnormal
Headlight leveling motor LH (Internal malfunction)
Harness open circuit (headlight ECU sub-assembly LH to headlight leveling motor LH)
Headlight ECU sub-assembly LH (Internal malfunction)
- ○ Headlight leveling motor RH power supply abnormal
Headlight leveling motor RH (Internal malfunction)
LIN communication circuit (open)
Harness open circuit (headlight ECU sub-assembly RH to headlight leveling motor RH)
Headlight ECU sub-assembly RH (Internal malfunction)
Headlight ECU sub-assembly LH (Internal malfunction)

HINT:

If the DTCs are output simultaneously, the inspection area can be narrowed down.


WIRING DIAGRAM

for LHD


w/ Adaptive High Beam System
E442330E09
1.625,0.74 2.177,0.948 0.552,0.208 10 false LIN I/F 0.948,2.323 1.563,2.521 0.615,0.198 10 false LINL 2.271,1.063 2.885,1.26 0.615,0.198 10 false LIN1_1 2.344,1.635 3.115,1.833 0.771,0.198 10 false ACTB 2.333,2.146 3.104,2.344 0.771,0.198 10 false ACTG 2,3.99 2.313,4.188 0.313,0.198 10 false IG 2,1.396 2.313,1.594 0.313,0.198 10 false IG 2.146,4.24 2.76,4.438 0.615,0.198 10 false PSWH2+ 0.594,2.49 1.052,2.688 0.458,0.198 10 false B4 0.615,2.292 0.927,2.49 0.313,0.198 10 false 20 2.906,1.26 3.063,1.458 0.156,0.198 10 false C 2.917,2.271 3.073,2.469 0.156,0.198 10 false B 2.917,1.76 3.073,1.958 0.156,0.198 10 false B 2.917,4.969 3.073,5.167 0.156,0.198 10 false C 2.906,3.75 3.063,3.948 0.156,0.198 10 false C 2.917,4.365 3.073,4.563 0.156,0.198 10 false C 5.198,5.688 5.354,5.885 0.156,0.198 10 false D 5.531,3.75 5.99,3.948 0.458,0.198 10 false LIN 2.865,1.052 3.177,1.25 0.313,0.198 10 false 12 2.906,1.563 3.063,1.76 0.156,0.198 10 false 9 2.875,2.073 3.188,2.271 0.313,0.198 10 false 18 5.042,2.813 6.875,3.094 1.833,0.281 10 false Headlight Leveling Motor LH 2.875,3.552 3.104,3.76 0.229,0.208 10 false 13 2.917,4.167 3.073,4.365 0.156,0.198 10 false 1 2.927,4.771 3.083,4.969 0.156,0.198 10 false 2 5.229,3.583 5.615,3.823 0.385,0.24 10 false 13 5.229,4.25 5.594,4.521 0.365,0.271 10 false 12 5.25,4.854 5.438,5.042 0.188,0.188 10 false 21 5.51,4.375 6.219,4.646 0.708,0.271 10 false ADD+ 5.521,4.979 6.188,5.281 0.667,0.302 10 false ADD- 5.208,5.854 6.958,6.042 1.75,0.188 10 false Light Control LED ECU LH 3.969,6.521 6.573,6.719 2.604,0.198 10 false Headlight Unit Assembly LH 0.656,6.844 3.198,7.052 2.542,0.208 10 false Headlight ECU Sub-assembly LH 0.198,6.708 0.354,6.906 0.156,0.198 10 false A 0.813,7.458 2.625,7.677 1.813,0.219 10 false : LIN Communication Line 5.042,2.656 5.354,2.854 0.313,0.198 10 false F 5.292,1.083 5.448,1.281 0.156,0.198 10 false 3 5.302,1.635 5.458,1.833 0.156,0.198 10 false 1 5.313,2.146 5.469,2.344 0.156,0.198 10 false 4 2.25,3.563 2.865,3.76 0.615,0.198 10 false LIN1_2 2.177,4.813 2.792,5.01 0.615,0.198 10 false PSWH2-

w/ Adaptive High Beam System
E442331E09
0.188,0.188 0.542,0.479 0.354,0.292 10 false A 0.594,2.49 1.052,2.688 0.458,0.198 10 false B7 0.615,2.302 0.927,2.5 0.313,0.198 10 false 20 2.01,1.406 2.323,1.604 0.313,0.198 10 false IG 2,4.01 2.313,4.208 0.313,0.198 10 false IG 2.271,1.063 3.042,1.26 0.771,0.198 10 false LIN1_1 2.333,2.125 3.104,2.323 0.771,0.198 10 false ACTG 2.344,1.615 3.115,1.813 0.771,0.198 10 false ACTB 2.917,1.25 3.073,1.448 0.156,0.198 10 false C 2.927,2.271 3.083,2.469 0.156,0.198 10 false B 2.927,1.76 3.083,1.958 0.156,0.198 10 false B 2.875,1.042 3.188,1.24 0.313,0.198 10 false 12 2.927,1.563 3.083,1.76 0.156,0.198 10 false 9 2.885,2.063 3.198,2.26 0.313,0.198 10 false 18 5.115,2.656 5.271,2.854 0.156,0.198 10 false F 5.302,2.146 5.458,2.344 0.156,0.198 10 false 4 5.292,1.094 5.448,1.292 0.156,0.198 10 false 3 5.292,1.646 5.448,1.844 0.156,0.198 10 false 1 5.125,2.802 6.896,3.146 1.771,0.344 10 false Headlight Leveling Motor RH 2.25,3.563 3.021,3.76 0.771,0.198 10 false LIN1_2 2.146,4.26 2.76,4.458 0.615,0.198 10 false PSWH2+ 2.177,4.833 2.792,5.031 0.615,0.198 10 false PSWH2- 2.917,4.969 3.073,5.167 0.156,0.198 10 false C 2.906,3.76 3.063,3.958 0.156,0.198 10 false C 2.906,4.385 3.063,4.583 0.156,0.198 10 false C 2.906,4.188 3.063,4.385 0.156,0.198 10 false 1 2.865,3.552 3.156,3.823 0.292,0.271 10 false 13 2.927,4.771 3.396,5.031 0.469,0.26 10 false 2 5.229,4.271 5.51,4.51 0.281,0.24 10 false 12 5.219,3.594 5.531,3.792 0.313,0.198 10 false 13 5.51,3.75 5.969,3.948 0.458,0.198 10 false LIN 5.25,4.854 5.563,5.052 0.313,0.198 10 false 21 5.521,4.365 6.052,4.594 0.531,0.229 10 false ADD+ 5.521,4.948 6.25,5.208 0.729,0.26 10 false ADD- 5.115,5.823 6.823,6.052 1.708,0.229 10 false Light Control LED ECU RH 3.875,6.521 6.479,6.719 2.604,0.198 10 false Headlight Unit Assembly RH 0.635,6.854 4.156,7.052 3.521,0.198 10 false Headlight ECU Sub-assembly RH 0.823,7.469 2.708,7.646 1.885,0.177 10 false : LIN Communication Line 0.927,2.333 1.26,2.51 0.333,0.177 10 false LINL 5.104,5.667 5.26,5.865 0.156,0.198 10 false D

w/o Adaptive High Beam System
E463613E02
5.073,6.76 6.99,7.281 1.917,0.521 10 false Headlight Leveling Motor RH 3.76,3.083 6.5,3.49 2.74,0.406 10 false Headlight Unit Assembly LH 3.823,7.25 6.563,7.656 2.74,0.406 10 false Headlight Unit Assembly RH 5.073,6.604 6.99,7.125 1.917,0.521 10 false F 2.875,5.083 4.792,5.604 1.917,0.521 10 false C 2.875,5.594 4.792,6.115 1.917,0.521 10 false B 2.875,6.104 4.792,6.625 1.917,0.521 10 false B 0.573,5.073 2.49,5.594 1.917,0.521 10 false B7 0.573,4.875 2.49,5.396 1.917,0.521 10 false 20 0.917,4.885 2.833,5.406 1.917,0.521 10 false LINL 0.938,0.813 2.854,1.333 1.917,0.521 10 false LINL 0.552,0.958 2.469,1.479 1.917,0.521 10 false B4 0.583,0.771 2.5,1.292 1.917,0.521 10 false 20 2.302,5.99 4.219,6.51 1.917,0.521 10 false ACTG 2.281,5.49 4.198,6.01 1.917,0.521 10 false ACTB 2.229,4.917 4.146,5.438 1.917,0.521 10 false LIN1_1 1.719,5.375 3.635,5.896 1.917,0.521 10 false IG 2.833,4.896 4.75,5.417 1.917,0.521 10 false 12 2.875,5.406 4.792,5.927 1.917,0.521 10 false 9 2.813,5.927 4.729,6.448 1.917,0.521 10 false 18 5.24,4.938 7.156,5.458 1.917,0.521 10 false 3 5.24,5.49 7.156,6.01 1.917,0.521 10 false 1 5.24,5.979 7.156,6.5 1.917,0.521 10 false 4 5.24,0.802 7.156,1.323 1.917,0.521 10 false 3 5.24,1.354 7.156,1.875 1.917,0.521 10 false 1 5.24,1.854 7.156,2.375 1.917,0.521 10 false 4 5.052,2.635 6.969,3.156 1.917,0.521 10 false Headlight Leveling Motor LH 5.063,2.469 6.979,2.99 1.917,0.521 10 false F 0.875,7.594 3.615,8 2.74,0.406 10 false Headlight ECU Sub-assembly RH 0.781,3.417 3.521,3.823 2.74,0.406 10 false Headlight ECU Sub-assembly LH 2.844,0.771 4.76,1.292 1.917,0.521 10 false 12 2.219,0.792 4.135,1.313 1.917,0.521 10 false LIN1_1 2.865,0.969 4.781,1.49 1.917,0.521 10 false C 2.26,1.365 4.177,1.885 1.917,0.521 10 false ACTB 2.875,1.281 4.792,1.802 1.917,0.521 10 false 9 2.885,1.469 4.802,1.99 1.917,0.521 10 false B 2.875,1.979 4.792,2.5 1.917,0.521 10 false B 2.24,1.906 4.156,2.427 1.917,0.521 10 false ACTG 1.771,1.271 3.688,1.792 1.917,0.521 10 false IG 2.823,1.802 4.74,2.323 1.917,0.521 10 false 18 0.823,8.313 3.563,8.719 2.74,0.406 10 false : LIN Communication Line 1.573,0.469 3.49,0.99 1.917,0.521 10 false LIN I/F


for RHD


w/ Adaptive High Beam System
E479675E05
2.74,0.781 3.292,0.99 0.552,0.208 10 false LIN I/F 0.844,2.365 1.458,2.563 0.615,0.198 10 false LINL 3.427,1.073 4.042,1.271 0.615,0.198 10 false LIN1_1 3.458,1.646 4.229,1.844 0.771,0.198 10 false ACTB 3.438,2.167 4.208,2.365 0.771,0.198 10 false ACTG 3.042,3.99 3.667,4.313 0.625,0.323 10 false ECUB 3.156,1.406 3.469,1.604 0.313,0.198 10 false IGR 3.271,4.292 3.885,4.49 0.615,0.198 10 false PSWH2+ 1.708,2.5 2.167,2.698 0.458,0.198 10 false B88 1.75,2.281 2.063,2.479 0.313,0.198 10 false 20 4.052,1.26 4.208,1.458 0.156,0.198 10 false C 4.052,2.271 4.208,2.469 0.156,0.198 10 false B 4.052,1.76 4.208,1.958 0.156,0.198 10 false B 4.052,4.969 4.208,5.167 0.156,0.198 10 false C 5.063,3.76 5.344,3.948 0.281,0.188 10 false D 4.052,4.365 4.208,4.563 0.156,0.198 10 false C 5.375,3.76 5.833,3.958 0.458,0.198 10 false LIN 4.021,1.073 4.333,1.271 0.313,0.198 10 false 12 4.052,1.563 4.208,1.76 0.156,0.198 10 false 9 4.021,2.073 4.333,2.271 0.313,0.198 10 false 18 5.042,2.813 6.875,3.094 1.833,0.281 10 false Headlight Leveling Motor LH 4.063,3.573 4.292,3.781 0.229,0.208 10 false 13 4.052,4.177 4.208,4.375 0.156,0.198 10 false 1 4.063,4.792 4.219,4.99 0.156,0.198 10 false 2 5.073,3.552 5.458,3.792 0.385,0.24 10 false 13 5.031,4.198 5.396,4.469 0.365,0.271 10 false 12 5.042,4.792 5.229,4.979 0.188,0.188 10 false 21 5.396,4.365 6.104,4.635 0.708,0.271 10 false AHSB 5.385,4.969 6.052,5.271 0.667,0.302 10 false AHSG 5.146,5.542 6.896,5.729 1.75,0.188 10 false Light Control LED ECU LH 4.552,6.24 7.156,6.438 2.604,0.198 10 false Headlight Assembly LH 1.927,6.583 4.417,7.385 2.49,0.802 10 false Headlight ECU Sub-assembly LH 0.198,6.708 0.354,6.906 0.156,0.198 10 false A 0.813,7.458 2.625,7.677 1.813,0.219 10 false : LIN Communication Line 5.042,2.656 5.354,2.854 0.313,0.198 10 false F 5.167,1.083 5.323,1.281 0.156,0.198 10 false 3 5.188,1.635 5.344,1.833 0.156,0.198 10 false 1 5.188,2.198 5.344,2.396 0.156,0.198 10 false 4 3.417,3.583 4.031,3.781 0.615,0.198 10 false LIN1_2 3.281,4.865 3.896,5.063 0.615,0.198 10 false PSWH2- 0.51,2.333 1.125,2.531 0.615,0.198 10 false 9 0.438,2.5 0.896,2.698 0.458,0.198 10 false BB6 5.063,4.365 5.344,4.552 0.281,0.188 10 false D 5.063,4.969 5.344,5.156 0.281,0.188 10 false D 4.052,3.76 4.208,3.958 0.156,0.198 10 false C 0.76,6.25 2.021,6.656 1.26,0.406 10 false Headlight Cord LH 2.083,2.354 2.698,2.552 0.615,0.198 10 false LINL

w/ Adaptive High Beam System
E479676E06
0.844,2.365 1.458,2.563 0.615,0.198 10 false LINL 3.427,1.073 4.042,1.271 0.615,0.198 10 false LIN1_1 3.458,1.646 4.229,1.844 0.771,0.198 10 false ACTB 3.479,2.167 4.25,2.365 0.771,0.198 10 false ACTG 3.052,4.01 3.698,4.281 0.646,0.271 10 false ECUB 3.156,1.406 3.469,1.604 0.313,0.198 10 false IGR 3.271,4.292 3.885,4.49 0.615,0.198 10 false PSWH2+ 1.708,2.5 2.167,2.698 0.458,0.198 10 false B89 1.75,2.281 2.063,2.479 0.313,0.198 10 false 20 4.052,1.26 4.208,1.458 0.156,0.198 10 false C 4.052,2.271 4.208,2.469 0.156,0.198 10 false B 4.052,1.76 4.208,1.958 0.156,0.198 10 false B 4.052,4.979 4.208,5.177 0.156,0.198 10 false C 5.063,3.76 5.344,3.948 0.281,0.188 10 false D 4.052,4.365 4.208,4.563 0.156,0.198 10 false C 5.375,3.76 5.833,3.958 0.458,0.198 10 false LIN 4.063,1.073 4.375,1.271 0.313,0.198 10 false 12 4.052,1.563 4.208,1.76 0.156,0.198 10 false 9 4.021,2.073 4.333,2.271 0.313,0.198 10 false 18 5.042,2.813 6.875,3.094 1.833,0.281 10 false Headlight Leveling Motor RH 4.042,3.573 4.271,3.781 0.229,0.208 10 false 13 4.052,4.177 4.208,4.375 0.156,0.198 10 false 1 4.073,4.792 4.229,4.99 0.156,0.198 10 false 2 5.073,3.583 5.458,3.823 0.385,0.24 10 false 13 5.031,4.198 5.396,4.469 0.365,0.271 10 false 12 5.042,4.792 5.229,4.979 0.188,0.188 10 false 21 5.406,4.385 6.115,4.656 0.708,0.271 10 false AHSB 5.406,4.99 6.073,5.292 0.667,0.302 10 false AHSG 5.104,5.75 6.854,5.938 1.75,0.188 10 false Light Control LED ECU RH 4.552,6.385 7.156,6.583 2.604,0.198 10 false Headlight Assembly RH 1.875,6.75 4.26,7.292 2.385,0.542 10 false Headlight ECU Sub-assembly RH 0.844,7.333 2.656,7.552 1.813,0.219 10 false : LIN Communication Line 5.042,2.656 5.354,2.854 0.313,0.198 10 false F 5.167,1.083 5.323,1.281 0.156,0.198 10 false 3 5.188,1.635 5.344,1.833 0.156,0.198 10 false 1 5.188,2.198 5.344,2.396 0.156,0.198 10 false 4 3.417,3.583 4.031,3.781 0.615,0.198 10 false LIN1_2 3.281,4.865 3.896,5.063 0.615,0.198 10 false PSWH2- 0.51,2.333 1.125,2.531 0.615,0.198 10 false 9 0.438,2.5 0.896,2.698 0.458,0.198 10 false BB8 5.063,4.365 5.344,4.552 0.281,0.188 10 false D 5.063,4.969 5.344,5.156 0.281,0.188 10 false D 4.052,3.76 4.208,3.958 0.156,0.198 10 false C 0.188,0.135 0.646,0.333 0.458,0.198 10 false A 0.719,6.375 1.948,6.76 1.229,0.385 10 false Headlight Cord RH 2.135,2.354 2.75,2.552 0.615,0.198 10 false LINL

w/o Adaptive High Beam System
E502872E01
5.073,6.76 6.99,7.281 1.917,0.521 10 false Headlight Leveling Motor RH 4.417,3.073 7.156,3.479 2.74,0.406 10 false Headlight Unit Assembly LH 4.417,7.333 7.156,7.74 2.74,0.406 10 false Headlight Unit Assembly RH 5.073,6.604 6.99,7.125 1.917,0.521 10 false F 4,5.229 5.917,5.75 1.917,0.521 10 false C 4,5.74 5.917,6.26 1.917,0.521 10 false B 4,6.25 5.917,6.771 1.917,0.521 10 false B 1.792,5.219 3.708,5.74 1.917,0.521 10 false B89 2.188,5.083 4.104,5.604 1.917,0.521 10 false LINL 2.177,0.813 4.094,1.333 1.917,0.521 10 false LINL 1.792,0.969 3.708,1.49 1.917,0.521 10 false B88 1.802,0.771 3.719,1.292 1.917,0.521 10 false 20 3.365,6.135 5.281,6.656 1.917,0.521 10 false ACTG 3.406,5.615 5.323,6.135 1.917,0.521 10 false ACTB 3.365,5.042 5.281,5.563 1.917,0.521 10 false LIN1_1 2.854,5.51 4.771,6.031 1.917,0.521 10 false IG 3.969,5.042 5.885,5.563 1.917,0.521 10 false 12 4,5.531 5.917,6.052 1.917,0.521 10 false 9 3.969,6.042 5.885,6.563 1.917,0.521 10 false 18 5.24,5.063 7.156,5.583 1.917,0.521 10 false 3 5.24,5.625 7.156,6.146 1.917,0.521 10 false 1 5.24,6.146 7.156,6.667 1.917,0.521 10 false 4 5.24,0.802 7.156,1.323 1.917,0.521 10 false 3 5.24,1.354 7.156,1.875 1.917,0.521 10 false 1 5.24,1.854 7.156,2.375 1.917,0.521 10 false 4 5.052,2.635 6.969,3.156 1.917,0.521 10 false Headlight Leveling Motor LH 5.063,2.469 6.979,2.99 1.917,0.521 10 false F 2.031,7.677 4.771,8.083 2.74,0.406 10 false Headlight ECU Sub-assembly RH 2.135,3.385 4.875,3.792 2.74,0.406 10 false Headlight ECU Sub-assembly LH 3.938,0.781 5.854,1.302 1.917,0.521 10 false 12 3.333,0.792 5.25,1.313 1.917,0.521 10 false LIN1_1 4.01,0.969 5.927,1.49 1.917,0.521 10 false C 3.417,1.365 5.333,1.885 1.917,0.521 10 false ACTB 4,1.281 5.917,1.802 1.917,0.521 10 false 9 4.01,1.469 5.927,1.99 1.917,0.521 10 false B 4.01,1.979 5.927,2.5 1.917,0.521 10 false B 3.396,1.906 5.313,2.427 1.917,0.521 10 false ACTG 2.781,1.271 4.698,1.792 1.917,0.521 10 false IG 3.99,1.813 5.906,2.333 1.917,0.521 10 false 18 0.823,8.313 3.563,8.719 2.74,0.406 10 false : LIN Communication Line 2.635,0.469 4.552,0.99 1.917,0.521 10 false LIN I/F 0.594,0.969 2.51,1.49 1.917,0.521 10 false BB6 0.604,5.229 2.521,5.75 1.917,0.521 10 false BB8 1.813,5.031 3.729,5.552 1.917,0.521 10 false 20 0.667,5.042 2.583,5.563 1.917,0.521 10 false 9 0.677,0.771 2.594,1.292 1.917,0.521 10 false 9 0.896,3.083 3.635,3.49 2.74,0.406 10 false Headlight Cord LH 0.896,7.354 3.635,7.76 2.74,0.406 10 false Headlight Cord RH 1.021,0.781 2.938,1.302 1.917,0.521 10 false LINL 0.979,5.063 2.896,5.583 1.917,0.521 10 false LINL


CAUTION / NOTICE / HINT

NOTICE:
·

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Headlight ECU)>REGISTRATION

·

When replacing the headlight ECU sub-assembly LH, always replace it with a new one. If a headlight ECU sub-assembly LH which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.CHECK VEHICLE TYPE
Result:
Result Proceed to
w/ Adaptive high beam system A
w/o Adaptive high beam system B



A

2.CLEAR DTC

B

60.CLEAR DTC
2.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are not output A
B242487, B242587, B244087 and B244187 are output B
B242487 and B244087 are output C
B242587 and B244187 are output D
B242487 is output E
B242587 is output F
B244087 is output G
B244187 is output H



Post-procedure1

d.

None



A

B

4.CHECK VEHICLE TYPE

C

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

D

49.CHECK VEHICLE TYPE

E

56.INSPECT HEADLIGHT UNIT ASSEMBLY LH

F

58.INSPECT HEADLIGHT UNIT ASSEMBLY RH

G

H

4.CHECK VEHICLE TYPE
Result:
Result Proceed to
for LHD A
for RHD B



A

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)

B

26.INSPECT HEADLIGHT CORD LH
5.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)

Pre-procedure1

a.

Disconnect the B4 headlight ECU sub-assembly LH connector.


b.

Disconnect the B7 headlight ECU sub-assembly RH connector.


Procedure1


Post-procedure1

d.

None



OK

6.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CLEAR DTC

Pre-procedure1

a.

Connect the B4 No. 1 headlight ECU sub-assembly LH connector.


Procedure1

b.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462
Result:
Proceed to
NEXT



Post-procedure1

c.

None



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B242587 and B244187 are output B



Post-procedure1

d.

None



A

8.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

B

17.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH
8.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH
a.

Remove the headlight ECU sub-assembly LH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



b.

Connect the B4 headlight ECU sub-assembly LH connector.


c.

Connect the B7 headlight ECU sub-assembly RH connector.


Result:
Proceed to
NEXT



NEXT

9.CLEAR DTC
9.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

10.CHECK FOR DTC
10.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B242487 and B244087 are output B



Post-procedure1

d.

None



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

B

11.CHECK HEADLIGHT LEVELING MOTOR LH
11.CHECK HEADLIGHT LEVELING MOTOR LH
a.

Connect all of the disconnected connectors.


b.

Disconnect the headlight leveling motor LH connector.


Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
12.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

13.CHECK FOR DTC
13.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B242487 is output B



Post-procedure1

d.

None



A

14.CHECK LIGHT CONTROL LED ECU LH

B

REPLACE HEADLIGHT LEVELING MOTOR LH

14.CHECK LIGHT CONTROL LED ECU LH
a.

Connect all of the disconnected connectors.


b.

Disconnect the light control LED ECU LH connector.


Result:
Proceed to
NEXT



NEXT

15.CLEAR DTC
15.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

16.CHECK FOR DTC
16.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B244087 is output B



Post-procedure1

d.

None



A

REPLACE HEADLIGHT UNIT ASSEMBLY LH

B

REPLACE LIGHT CONTROL LED ECU LH

17.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH
a.

Remove the headlight ECU sub-assembly RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



b.

Connect the B7 headlight ECU sub-assembly RH connector.


Result:
Proceed to
NEXT



NEXT

18.CLEAR DTC
18.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

19.CHECK FOR DTC
19.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B242587 and B244187 are output B



Post-procedure1

d.

None



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

B

20.CHECK HEADLIGHT LEVELING MOTOR RH
20.CHECK HEADLIGHT LEVELING MOTOR RH
a.

Connect all of the disconnected connectors.


b.

Disconnect the headlight leveling motor RH connector.


Result:
Proceed to
NEXT



NEXT

21.CLEAR DTC
21.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

22.CHECK FOR DTC
22.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B242587 is output B



Post-procedure1

d.

None



A

23.CHECK LIGHT CONTROL LED ECU RH

B

REPLACE HEADLIGHT LEVELING MOTOR RH

23.CHECK LIGHT CONTROL LED ECU RH
a.

Connect all of the disconnected connectors.


b.

Disconnect the light control LED ECU RH connector.


Result:
Proceed to
NEXT



NEXT

24.CLEAR DTC
24.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

25.CHECK FOR DTC
25.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B244187 is output B



Post-procedure1

d.

None



A

REPLACE HEADLIGHT UNIT ASSEMBLY RH

B

REPLACE LIGHT CONTROL LED ECU RH

26.INSPECT HEADLIGHT CORD LH

Pre-procedure1

a.

Remove the headlight cord LH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY



Procedure1

b.
E483588C20
1.563,0.365 1.969,0.615 0.406,0.25 1.479,2.323 1.885,2.573 0.406,0.25 2.24,3.958 1.927,3.5 true 2.292,2.01 2.083,1.552 true 1.646,0.417 2.042,0.771 0.396,0.354 10 false B88 1.563,2.375 2.177,2.906 0.615,0.531 10 false BB6 0.344,0.188 0.646,0.469 0.302,0.281 10 false *a 2.229,2.052 2.844,2.583 0.615,0.531 10 false LINL 2.323,3.896 2.938,4.427 0.615,0.531 10 false LINL
*a Component without harness connected
(Headlight Cord LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(BB6,B88)Location & Routing

Click Connector(BB6)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Engine Room Main Wire and No. 2 Lamp Wire

Click Connector(B88)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly LH

BB6-9 (LINL) or B88-20 (LINL) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

27.INSPECT HEADLIGHT CORD RH

NG

27.INSPECT HEADLIGHT CORD RH

Pre-procedure1

a.

Remove the headlight cord RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY



Procedure1

b.
E483588C21
1.563,0.365 1.969,0.615 0.406,0.25 1.479,2.323 1.885,2.573 0.406,0.25 2.24,3.958 1.927,3.5 true 2.292,2.01 2.083,1.552 true 1.646,0.417 1.958,0.76 0.313,0.344 10 false B89 1.563,2.375 2.177,2.906 0.615,0.531 10 false BB8 0.344,0.188 0.646,0.469 0.302,0.281 10 false *a 2.229,2.052 2.844,2.583 0.615,0.531 10 false LINL 2.323,3.896 2.938,4.427 0.615,0.531 10 false LINL
*a Component without harness connected
(Headlight Cord RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(BB8,B89)Location & Routing

Click Connector(BB8)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Engine Room Main Wire and Lamp Wire

Click Connector(B89)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly RH

BB8-9 (LINL) or B89-20 (LINL) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

28.CHECK HARNESS AND CONNECTOR (HEADLIGHT CORD LH - HEADLIGHT CORD RH)

NG

28.CHECK HARNESS AND CONNECTOR (HEADLIGHT CORD LH - HEADLIGHT CORD RH)

OK

29.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.CLEAR DTC

Pre-procedure1

a.

Connect the B88 No. 1 headlight ECU sub-assembly LH connector.


b.

Connect the BB6 headlight cord LH connector.


Procedure1

c.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462
Result:
Proceed to
NEXT



Post-procedure1

d.

None



NEXT

30.CHECK FOR DTC
30.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B242587 and B244187 are output B



Post-procedure1

d.

None



A

31.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

B

40.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH
31.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH
a.

Remove the headlight ECU sub-assembly LH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



b.

Connect the B88 headlight ECU sub-assembly LH connector.


c.

Connect the B89 headlight ECU sub-assembly RH connector.


d.

Connect the BB8 headlight cord RH connector.


Result:
Proceed to
NEXT



NEXT

32.CLEAR DTC
32.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

33.CHECK FOR DTC
33.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B242487 and B244087 are output B



Post-procedure1

d.

None



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

B

34.CHECK HEADLIGHT LEVELING MOTOR LH
34.CHECK HEADLIGHT LEVELING MOTOR LH
a.

Connect all of the disconnected connectors.


b.

Disconnect the headlight leveling motor LH connector.


Result:
Proceed to
NEXT



NEXT

35.CLEAR DTC
35.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

36.CHECK FOR DTC
36.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B242487 is output B



Post-procedure1

d.

None



A

37.CHECK LIGHT CONTROL LED ECU LH

B

REPLACE HEADLIGHT LEVELING MOTOR LH

37.CHECK LIGHT CONTROL LED ECU LH
a.

Connect all of the disconnected connectors.


b.

Disconnect the light control LED ECU LH connector.


Result:
Proceed to
NEXT



NEXT

38.CLEAR DTC
38.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

39.CHECK FOR DTC
39.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B244087 is output B



Post-procedure1

d.

None



A

REPLACE HEADLIGHT UNIT ASSEMBLY LH

B

REPLACE LIGHT CONTROL LED ECU LH

40.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH
a.

Remove the headlight ECU sub-assembly RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



b.

Connect the B89 headlight ECU sub-assembly RH connector.


c.

Connect the BB8 headlight cord RH connector.


Result:
Proceed to
NEXT



NEXT

41.CLEAR DTC
41.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

42.CHECK FOR DTC
42.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B242587 and B244187 are output B



Post-procedure1

d.

None



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

B

43.CHECK HEADLIGHT LEVELING MOTOR RH
43.CHECK HEADLIGHT LEVELING MOTOR RH
a.

Connect all of the disconnected connectors.


b.

Disconnect the headlight leveling motor RH connector.


Result:
Proceed to
NEXT



NEXT

44.CLEAR DTC
44.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

45.CHECK FOR DTC
45.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B242587 is output B



Post-procedure1

d.

None



A

46.CHECK LIGHT CONTROL LED ECU RH

B

REPLACE HEADLIGHT LEVELING MOTOR RH

46.CHECK LIGHT CONTROL LED ECU RH
a.

Connect all of the disconnected connectors.


b.

Disconnect the light control LED ECU RH connector.


Result:
Proceed to
NEXT



NEXT

47.CLEAR DTC
47.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

48.CHECK FOR DTC
48.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B244187 is output B



Post-procedure1

d.

None



A

REPLACE HEADLIGHT UNIT ASSEMBLY RH

B

REPLACE LIGHT CONTROL LED ECU RH

49.CHECK VEHICLE TYPE
Result:
Result Proceed to
for LHD A
for RHD B



A

50.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)

B

52.INSPECT HEADLIGHT CORD LH
50.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)

Pre-procedure1

a.

Disconnect the B4 headlight ECU sub-assembly LH connector.


b.

Disconnect the B7 headlight ECU sub-assembly RH connector.


Procedure1


Post-procedure1

d.

None



OK

51.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

51.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH

Pre-procedure1

a.

Remove the headlight ECU sub-assembly RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

E465495C01
2.104,0.302 2.573,0.552 0.469,0.25 5.771,0.563 6.24,0.813 0.469,0.25 2.49,2.083 2.333,2.083 2.333,2.083 2.125,1.26 true 6.167,2.083 6,2.083 6,2.083 5.854,1.479 true 5.406,2.094 5.573,2.094 5.573,2.094 5.75,1.479 true 0.188,0.115 0.5,0.313 0.313,0.198 10 false *a 2.271,0.333 2.583,0.531 0.313,0.198 10 false B7 2.542,1.99 2.906,2.219 0.365,0.229 10 false LINL 4.917,2 5.458,2.229 0.542,0.229 10 false LIN1_2 5.948,0.604 6.313,0.833 0.365,0.229 10 false C 6.25,2 6.792,2.229 0.542,0.229 10 false LIN1_1
*a Component without harness connected
(Headlight ECU Sub-assembly RH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B7)Location & Routing

Click Connector(B7)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly RH

B7-20 (LINL) - C-12 (LIN1_1) Always Below 1 Ω
B7-20 (LINL) - C-13 (LIN1_2) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

52.INSPECT HEADLIGHT CORD LH

Pre-procedure1

a.

Remove the headlight cord LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


Procedure1

b.
E483588C20
1.563,0.365 1.969,0.615 0.406,0.25 1.479,2.323 1.885,2.573 0.406,0.25 2.24,3.958 1.927,3.5 true 2.292,2.01 2.083,1.552 true 1.646,0.417 2.042,0.771 0.396,0.354 10 false B88 1.563,2.375 2.177,2.906 0.615,0.531 10 false BB6 0.344,0.188 0.646,0.469 0.302,0.281 10 false *a 2.229,2.052 2.844,2.583 0.615,0.531 10 false LINL 2.323,3.896 2.938,4.427 0.615,0.531 10 false LINL
*a Component without harness connected
(Headlight Cord LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(BB6,B88)Location & Routing

Click Connector(BB6)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Engine Room Main Wire and No. 2 Lamp Wire

Click Connector(B88)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly LH

BB6-9 (LINL) - B88-20 (LINL) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

53.INSPECT HEADLIGHT CORD RH

NG

53.INSPECT HEADLIGHT CORD RH

Pre-procedure1

a.

Remove the headlight cord RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


Procedure1

b.
E483588C21
1.563,0.365 1.969,0.615 0.406,0.25 1.479,2.323 1.885,2.573 0.406,0.25 2.24,3.958 1.927,3.5 true 2.292,2.01 2.083,1.552 true 1.646,0.417 1.958,0.76 0.313,0.344 10 false B89 1.563,2.375 2.177,2.906 0.615,0.531 10 false BB8 0.344,0.188 0.646,0.469 0.302,0.281 10 false *a 2.229,2.052 2.844,2.583 0.615,0.531 10 false LINL 2.323,3.896 2.938,4.427 0.615,0.531 10 false LINL
*a Component without harness connected
(Headlight Cord RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(BB8,B89)Location & Routing

Click Connector(BB8)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Engine Room Main Wire and Lamp Wire

Click Connector(B89)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly RH

BB8-9 (LINL) - B89-20 (LINL) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

54.CHECK HARNESS AND CONNECTOR (HEADLIGHT CORD LH - HEADLIGHT CORD RH)

NG

54.CHECK HARNESS AND CONNECTOR (HEADLIGHT CORD LH - HEADLIGHT CORD RH)

OK

55.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

55.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH

Pre-procedure1

a.

Remove the headlight ECU sub-assembly RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

E465495C05
2.104,0.302 2.573,0.552 0.469,0.25 5.771,0.563 6.24,0.813 0.469,0.25 2.49,2.083 2.333,2.083 2.333,2.083 2.125,1.26 true 6.167,2.083 6,2.083 6,2.083 5.854,1.479 true 5.406,2.094 5.573,2.094 5.573,2.094 5.75,1.479 true 0.188,0.115 0.5,0.313 0.313,0.198 10 false *a 2.24,0.344 2.552,0.542 0.313,0.198 10 false B89 2.542,1.99 2.906,2.219 0.365,0.229 10 false LINL 4.917,2 5.458,2.229 0.542,0.229 10 false LIN1_2 5.948,0.604 6.313,0.833 0.365,0.229 10 false C 6.25,2 6.792,2.229 0.542,0.229 10 false LIN1_1
*a Component without harness connected
(Headlight ECU Sub-assembly RH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B89)Location & Routing

Click Connector(B89)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly RH

B89-20 (LINL) - C-12 (LIN1_1) Always Below 1 Ω
B89-20 (LINL) - C-13 (LIN1_2) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

56.INSPECT HEADLIGHT UNIT ASSEMBLY LH

Pre-procedure1

a.

Remove the headlight unit assembly LH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

E401599C07
1.156,0.677 1.51,0.906 0.354,0.229 3.417,0.677 3.771,0.906 0.354,0.229 5.719,0.677 6.073,0.906 0.354,0.229 3.938,2.26 3.781,1.885 false 1.938,2.198 1.833,1.677 false 1.385,2.177 1.677,1.844 false 0.354,0.698 0.667,0.896 0.313,0.198 10 false *a 2.667,0.635 2.979,0.833 0.313,0.198 10 false *a 4.802,0.635 5.115,0.833 0.313,0.198 10 false *b 1.292,0.708 1.604,0.906 0.313,0.198 10 false B 3.552,0.708 3.865,0.906 0.313,0.198 10 false C 5.885,0.708 6.198,0.906 0.313,0.198 10 false F 3.813,2.292 4.583,2.49 0.771,0.198 10 false LIN1_1 1.802,2.229 2.573,2.427 0.771,0.198 10 false ACTB 1.198,2.208 1.969,2.406 0.771,0.198 10 false ACTG
*a Component without harness connected
(to Headlight ECU Sub-assembly LH)
*b Component without harness connected
(to Headlight Leveling Motor LH)


Standard Resistance:
Tester Connection Condition Specified Condition
C-12 (LIN1_1) - F-3 Always Below 1 Ω
B-9 (ACTB) - F-1 Always Below 1 Ω
B-18 (ACTG) - F-4 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

57.INSPECT HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPLACE HEADLIGHT UNIT ASSEMBLY LH

57.INSPECT HEADLIGHT ECU SUB-ASSEMBLY LH

Pre-procedure1

a.

Connect all of the disconnected connectors.


b.

Disconnect the headlight leveling motor LH connector.


Procedure1

c.
E378482C13
1.458,0.417 1.938,0.635 0.479,0.219 0.115,0.104 0.427,0.26 0.313,0.156 10 false *a 1.677,0.458 1.99,0.615 0.313,0.156 10 false F
*a Component without harness connected
(to Headlight Leveling Motor LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F-1 - F-4 Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE HEADLIGHT LEVELING MOTOR LH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

58.INSPECT HEADLIGHT UNIT ASSEMBLY RH

Pre-procedure1

a.

Remove the headlight unit assembly RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

E401599C07
1.156,0.677 1.51,0.906 0.354,0.229 3.417,0.677 3.771,0.906 0.354,0.229 5.719,0.677 6.073,0.906 0.354,0.229 3.938,2.26 3.781,1.885 false 1.938,2.198 1.833,1.677 false 1.385,2.177 1.677,1.844 false 0.354,0.698 0.667,0.896 0.313,0.198 10 false *a 2.667,0.635 2.979,0.833 0.313,0.198 10 false *a 4.802,0.635 5.115,0.833 0.313,0.198 10 false *b 1.292,0.708 1.604,0.906 0.313,0.198 10 false B 3.552,0.708 3.865,0.906 0.313,0.198 10 false C 5.885,0.708 6.198,0.906 0.313,0.198 10 false F 3.813,2.292 4.583,2.49 0.771,0.198 10 false LIN1_1 1.802,2.229 2.573,2.427 0.771,0.198 10 false ACTB 1.198,2.208 1.969,2.406 0.771,0.198 10 false ACTG
*a Component without harness connected
(to Headlight ECU Sub-assembly RH)
*b Component without harness connected
(to Headlight Leveling Motor RH)


Standard Resistance:
Tester Connection Condition Specified Condition
C-12 (LIN1_1) - F-3 Always Below 1 Ω
B-9 (ACTB) - F-1 Always Below 1 Ω
B-18 (ACTG) - F-4 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

59.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPLACE HEADLIGHT UNIT ASSEMBLY RH

59.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH

Pre-procedure1

a.

Connect all of the disconnected connectors.


b.

Disconnect the headlight leveling motor RH connector.


Procedure1

c.
E378482C13
1.458,0.417 1.938,0.635 0.479,0.219 0.115,0.104 0.427,0.26 0.313,0.156 10 false *a 1.677,0.458 1.99,0.615 0.313,0.156 10 false F
*a Component without harness connected
(to Headlight Leveling Motor RH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F-1 - F-4 Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE HEADLIGHT LEVELING MOTOR RH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

60.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

61.CHECK FOR DTC
61.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487 and B242587 are not output A
B242487 and B24258 are output B
B242487 is output C
B242587 is output D



Post-procedure1

d.

None



A

B

62.CHECK VEHICLE TYPE

C

56.INSPECT HEADLIGHT UNIT ASSEMBLY LH

D

95.CHECK VEHICLE TYPE
62.CHECK VEHICLE TYPE
Result:
Result Proceed to
for LHD A
for RHD B



A

63.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)

B

78.INSPECT HEADLIGHT CORD LH
63.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)

Pre-procedure1

a.

Disconnect the B4 headlight ECU sub-assembly LH connector.


b.

Disconnect the B7 headlight ECU sub-assembly RH connector.


Procedure1


Post-procedure1

d.

None



OK

64.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

64.CLEAR DTC

Pre-procedure1

a.

Connect the B4 headlight ECU sub-assembly LH connector.


Procedure1

b.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462
Result:
Proceed to
NEXT



Post-procedure1

c.

None



NEXT

65.CHECK FOR DTC
65.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487 and B242587 are output A
B242587 is output B



Post-procedure1

d.

None



A

66.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

B

72.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH
66.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH
a.

Remove the headlight ECU sub-assembly LH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



b.

Connect the B4 headlight ECU sub-assembly LH connector.


c.

Connect the B7 headlight ECU sub-assembly RH connector.


Result:
Proceed to
NEXT



NEXT

67.CLEAR DTC
67.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

68.CHECK FOR DTC
68.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487 and B242587 are output A
B242487 are output B



Post-procedure1

d.

None



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

B

69.CHECK HEADLIGHT LEVELING MOTOR LH
69.CHECK HEADLIGHT LEVELING MOTOR LH
a.

Connect all of the disconnected connectors.


b.

Disconnect the headlight leveling motor LH connector.


Result:
Proceed to
NEXT



NEXT

70.CLEAR DTC
70.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

71.CHECK FOR DTC
71.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487 and B242587 are output A
B242487 is output B



Post-procedure1

d.

None



A

REPLACE HEADLIGHT UNIT ASSEMBLY LH

B

REPLACE HEADLIGHT LEVELING MOTOR LH

72.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH
a.

Remove the headlight ECU sub-assembly RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



b.

Connect the B7 headlight ECU sub-assembly RH connector.


Result:
Proceed to
NEXT



NEXT

73.CLEAR DTC
73.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

74.CHECK FOR DTC
74.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487 and B242587 are output A
B242587 is output B



Post-procedure1

d.

None



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

B

75.CHECK HEADLIGHT LEVELING MOTOR RH
75.CHECK HEADLIGHT LEVELING MOTOR RH
a.

Connect all of the disconnected connectors.


b.

Disconnect the headlight leveling motor RH connector.


Result:
Proceed to
NEXT



NEXT

76.CLEAR DTC
76.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

77.CHECK FOR DTC
77.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487 and B242587 are output A
B242587 is output B



Post-procedure1

d.

None



A

REPLACE HEADLIGHT UNIT ASSEMBLY RH

B

REPLACE HEADLIGHT LEVELING MOTOR RH

78.INSPECT HEADLIGHT CORD LH

Pre-procedure1

a.

Remove the headlight cord LH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY



Procedure1

b.
E483588C20
1.563,0.365 1.969,0.615 0.406,0.25 1.479,2.323 1.885,2.573 0.406,0.25 2.24,3.958 1.927,3.5 true 2.292,2.01 2.083,1.552 true 1.646,0.417 2.042,0.771 0.396,0.354 10 false B88 1.563,2.375 2.177,2.906 0.615,0.531 10 false BB6 0.344,0.188 0.646,0.469 0.302,0.281 10 false *a 2.229,2.052 2.844,2.583 0.615,0.531 10 false LINL 2.323,3.896 2.938,4.427 0.615,0.531 10 false LINL
*a Component without harness connected
(Headlight Cord LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(BB6,B88)Location & Routing

Click Connector(BB6)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Engine Room Main Wire and No. 2 Lamp Wire

Click Connector(B88)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly LH

BB6-9 (LINL) or B88-20 (LINL) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

79.INSPECT HEADLIGHT CORD RH

NG

79.INSPECT HEADLIGHT CORD RH

Pre-procedure1

a.

Remove the headlight cord RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY



Procedure1

b.
E483588C21
1.563,0.365 1.969,0.615 0.406,0.25 1.479,2.323 1.885,2.573 0.406,0.25 2.24,3.958 1.927,3.5 true 2.292,2.01 2.083,1.552 true 1.646,0.417 1.958,0.76 0.313,0.344 10 false B89 1.563,2.375 2.177,2.906 0.615,0.531 10 false BB8 0.344,0.188 0.646,0.469 0.302,0.281 10 false *a 2.229,2.052 2.844,2.583 0.615,0.531 10 false LINL 2.323,3.896 2.938,4.427 0.615,0.531 10 false LINL
*a Component without harness connected
(Headlight Cord RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(BB8,B89)Location & Routing

Click Connector(BB8)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Engine Room Main Wire and Lamp Wire

Click Connector(B89)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly RH

BB8-9 (LINL) or B89-20 (LINL) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

80.CHECK HARNESS AND CONNECTOR (HEADLIGHT CORD LH - HEADLIGHT CORD RH)

NG

80.CHECK HARNESS AND CONNECTOR (HEADLIGHT CORD LH - HEADLIGHT CORD RH)

OK

81.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

81.CLEAR DTC

Pre-procedure1

a.

Connect the B88 headlight ECU sub-assembly LH connector.


b.

Connect the BB6 headlight cord LH connector.


Procedure1

c.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462
Result:
Proceed to
NEXT



Post-procedure1

d.

None



NEXT

82.CHECK FOR DTC
82.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487 and B242587 are output A
B242587 is output B



Post-procedure1

d.

None



A

83.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

B

89.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH
83.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH
a.

Remove the headlight ECU sub-assembly LH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



b.

Connect the B88 headlight ECU sub-assembly LH connector.


c.

Connect the B89 headlight ECU sub-assembly RH connector.


d.

Connect the BB8 headlight cord RH connector.


Result:
Proceed to
NEXT



NEXT

84.CLEAR DTC
84.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

85.CHECK FOR DTC
85.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487 and B242587 are output A
B242487 are output B



Post-procedure1

d.

None



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

B

86.CHECK HEADLIGHT LEVELING MOTOR LH
86.CHECK HEADLIGHT LEVELING MOTOR LH
a.

Connect all of the disconnected connectors.


b.

Disconnect the headlight leveling motor LH connector.


Result:
Proceed to
NEXT



NEXT

87.CLEAR DTC
87.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

88.CHECK FOR DTC
88.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487 and B242587 are output A
B242487 is output B



Post-procedure1

d.

None



A

REPLACE HEADLIGHT UNIT ASSEMBLY LH

B

REPLACE HEADLIGHT LEVELING MOTOR LH

89.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH
a.

Remove the headlight ECU sub-assembly RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



b.

Connect the B89 headlight ECU sub-assembly RH connector.


c.

Connect the BB8 headlight cord RH connector.


Result:
Proceed to
NEXT



NEXT

90.CLEAR DTC
90.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

91.CHECK FOR DTC
91.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487 and B242587 are output A
B242587 is output B



Post-procedure1

d.

None



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

B

92.CHECK HEADLIGHT LEVELING MOTOR RH
92.CHECK HEADLIGHT LEVELING MOTOR RH
a.

Connect all of the disconnected connectors.


b.

Disconnect the headlight leveling motor RH connector.


Result:
Proceed to
NEXT



NEXT

93.CLEAR DTC
93.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

94.CHECK FOR DTC
94.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

c.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487 and B242587 are output A
B242587 is output B



Post-procedure1

d.

None



A

REPLACE HEADLIGHT UNIT ASSEMBLY RH

B

REPLACE HEADLIGHT LEVELING MOTOR RH

95.CHECK VEHICLE TYPE
Result:
Result Proceed to
for LHD A
for RHD B



A

96.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)

B

101.INSPECT HEADLIGHT CORD LH
96.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)

Pre-procedure1

a.

Disconnect the B4 headlight ECU sub-assembly LH connector.


b.

Disconnect the B7 headlight ECU sub-assembly RH connector.


Procedure1


Post-procedure1

d.

None



OK

97.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

97.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

Pre-procedure1

a.

Connect the B4 headlight ECU sub-assembly LH connector.


b.

Disconnect the C headlight unit assembly LH connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

E401599C09
1.156,0.677 1.51,0.906 0.354,0.229 3.417,0.677 3.771,0.906 0.354,0.229 5.719,0.677 6.073,0.906 0.354,0.229 3.938,2.26 3.781,1.885 false 2.083,2.354 1.979,1.833 false 0.354,0.698 0.667,0.896 0.313,0.198 10 false *a 2.667,0.635 2.979,0.833 0.313,0.198 10 false *a 4.802,0.635 5.115,0.833 0.313,0.198 10 false *b 1.292,0.708 1.604,0.906 0.313,0.198 10 false B 3.552,0.708 3.865,0.906 0.313,0.198 10 false C 5.885,0.708 6.198,0.906 0.313,0.198 10 false F 3.813,2.292 4.583,2.49 0.771,0.198 10 false LIN1_1 2.042,2.375 2.813,2.573 0.771,0.198 10 false LINL
*a Component without harness connected
(to Headlight ECU Sub-assembly LH)
*b Component without harness connected
(to Headlight Leveling Motor LH)


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B7)Location & Routing

Click Connector(B7)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly RH

C-12 (LIN1_1) - B7-20 (LINL) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

98.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

98.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH

Pre-procedure1

a.

Disconnect the B4 headlight ECU sub-assembly LH connector.


b.

Connect the B7 headlight ECU sub-assembly RH connector.


c.

Disconnect the C headlight unit assembly RH connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

E401599C09
1.156,0.677 1.51,0.906 0.354,0.229 3.417,0.677 3.771,0.906 0.354,0.229 5.719,0.677 6.073,0.906 0.354,0.229 3.938,2.26 3.781,1.885 false 2.083,2.354 1.979,1.833 false 0.354,0.698 0.667,0.896 0.313,0.198 10 false *a 2.667,0.635 2.979,0.833 0.313,0.198 10 false *a 4.802,0.635 5.115,0.833 0.313,0.198 10 false *b 1.292,0.708 1.604,0.906 0.313,0.198 10 false B 3.552,0.708 3.865,0.906 0.313,0.198 10 false C 5.885,0.708 6.198,0.906 0.313,0.198 10 false F 3.813,2.292 4.583,2.49 0.771,0.198 10 false LIN1_1 2.042,2.375 2.813,2.573 0.771,0.198 10 false LINL
*a Component without harness connected
(to Headlight ECU Sub-assembly RH)
*b Component without harness connected
(to Headlight Leveling Motor RH)


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B4)Location & Routing

Click Connector(B4)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly LH

C-12 (LIN1_1) - B4-20 (LINL) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

e.

None



OK

99.INSPECT HEADLIGHT UNIT ASSEMBLY RH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

99.INSPECT HEADLIGHT UNIT ASSEMBLY RH

Pre-procedure1

a.

Remove the headlight unit assembly RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

E401599C07
1.156,0.677 1.51,0.906 0.354,0.229 3.417,0.677 3.771,0.906 0.354,0.229 5.719,0.677 6.073,0.906 0.354,0.229 3.938,2.26 3.781,1.885 false 1.938,2.198 1.833,1.677 false 1.385,2.177 1.677,1.844 false 0.354,0.698 0.667,0.896 0.313,0.198 10 false *a 2.667,0.635 2.979,0.833 0.313,0.198 10 false *a 4.802,0.635 5.115,0.833 0.313,0.198 10 false *b 1.292,0.708 1.604,0.906 0.313,0.198 10 false B 3.552,0.708 3.865,0.906 0.313,0.198 10 false C 5.885,0.708 6.198,0.906 0.313,0.198 10 false F 3.813,2.292 4.583,2.49 0.771,0.198 10 false LIN1_1 1.802,2.229 2.573,2.427 0.771,0.198 10 false ACTB 1.198,2.208 1.969,2.406 0.771,0.198 10 false ACTG
*a Component without harness connected
(to Headlight ECU Sub-assembly RH)
*b Component without harness connected
(to Headlight Leveling Motor RH)


Standard Resistance:
Tester Connection Condition Specified Condition
C-12 (LIN1_1) - F-3 Always Below 1 Ω
B-9 (ACTB) - F-1 Always Below 1 Ω
B-18 (ACTG) - F-4 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

100.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPLACE HEADLIGHT UNIT ASSEMBLY RH

100.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH

Pre-procedure1

a.

Connect all of the disconnected connectors.


b.

Disconnect the headlight leveling motor RH connector.


Procedure1

c.
E378482C13
1.458,0.417 1.938,0.635 0.479,0.219 0.115,0.104 0.427,0.26 0.313,0.156 10 false *a 1.677,0.458 1.99,0.615 0.313,0.156 10 false F
*a Component without harness connected
(to Headlight Leveling Motor RH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F-1 - F-4 Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE HEADLIGHT LEVELING MOTOR RH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

101.INSPECT HEADLIGHT CORD LH

Pre-procedure1

a.

Remove the headlight cord LH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY



Procedure1

b.
E483588C20
1.563,0.365 1.969,0.615 0.406,0.25 1.479,2.323 1.885,2.573 0.406,0.25 2.24,3.958 1.927,3.5 true 2.292,2.01 2.083,1.552 true 1.646,0.417 2.042,0.771 0.396,0.354 10 false B88 1.563,2.375 2.177,2.906 0.615,0.531 10 false BB6 0.344,0.188 0.646,0.469 0.302,0.281 10 false *a 2.229,2.052 2.844,2.583 0.615,0.531 10 false LINL 2.323,3.896 2.938,4.427 0.615,0.531 10 false LINL
*a Component without harness connected
(Headlight Cord LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(BB6,B88)Location & Routing

Click Connector(BB6)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Engine Room Main Wire and No. 2 Lamp Wire

Click Connector(B88)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly LH

BB6-9 (LINL) - B88-20 (LINL) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

102.INSPECT HEADLIGHT CORD RH

NG

102.INSPECT HEADLIGHT CORD RH

Pre-procedure1

a.

Remove the headlight cord RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY



Procedure1

b.
E483588C21
1.563,0.365 1.969,0.615 0.406,0.25 1.479,2.323 1.885,2.573 0.406,0.25 2.24,3.958 1.927,3.5 true 2.292,2.01 2.083,1.552 true 1.646,0.417 1.958,0.76 0.313,0.344 10 false B89 1.563,2.375 2.177,2.906 0.615,0.531 10 false BB8 0.344,0.188 0.646,0.469 0.302,0.281 10 false *a 2.229,2.052 2.844,2.583 0.615,0.531 10 false LINL 2.323,3.896 2.938,4.427 0.615,0.531 10 false LINL
*a Component without harness connected
(Headlight Cord RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(BB8,B89)Location & Routing

Click Connector(BB8)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Engine Room Main Wire and Lamp Wire

Click Connector(B89)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly RH

BB8-9 (LINL) - B89-20 (LINL) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

103.CHECK HARNESS AND CONNECTOR (HEADLIGHT CORD LH - HEADLIGHT CORD RH)

NG

103.CHECK HARNESS AND CONNECTOR (HEADLIGHT CORD LH - HEADLIGHT CORD RH)

OK

104.INSPECT HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

104.INSPECT HEADLIGHT ECU SUB-ASSEMBLY LH

Pre-procedure1

a.

Remove the headlight ECU sub-assembly LH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

E465495C06
2.104,0.302 2.573,0.552 0.469,0.25 5.771,0.563 6.24,0.813 0.469,0.25 2.49,2.083 2.333,2.083 2.333,2.083 2.125,1.26 true 6.156,2.104 5.99,2.104 5.99,2.104 5.844,1.5 true 0.188,0.115 0.5,0.313 0.313,0.198 10 false *a 2.24,0.333 2.552,0.531 0.313,0.198 10 false B88 2.542,1.99 2.906,2.219 0.365,0.229 10 false LINL 5.948,0.604 6.313,0.833 0.365,0.229 10 false C 6.208,2.031 6.75,2.26 0.542,0.229 10 false LIN1_1
*a Component without harness connected
(Headlight ECU Sub-assembly LH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B88)Location & Routing

Click Connector(B88)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly LH

B88-20 (LINL) - C-12 (LIN1_1) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

105.INSPECT HEADLIGHT ASSEMBLY RH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

105.INSPECT HEADLIGHT ASSEMBLY RH

Pre-procedure1

a.

Remove the headlight ECU sub-assembly RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

E465495C07
2.104,0.302 2.573,0.552 0.469,0.25 5.771,0.563 6.24,0.813 0.469,0.25 2.49,2.083 2.333,2.083 2.333,2.083 2.125,1.26 true 6.167,2.063 6,2.063 6,2.063 5.854,1.458 true 0.188,0.115 0.5,0.313 0.313,0.198 10 false *a 2.229,0.344 2.542,0.542 0.313,0.198 10 false B89 2.542,1.99 2.906,2.219 0.365,0.229 10 false LINL 5.948,0.604 6.313,0.833 0.365,0.229 10 false C 6.229,1.979 6.771,2.208 0.542,0.229 10 false LIN1_1
*a Component without harness connected
(Headlight ECU Sub-assembly RH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B89)Location & Routing

Click Connector(B89)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly RH

B89-20 (LINL) - C-12 (LIN1_1) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

106.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

106.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

Pre-procedure1

a.

Connect the B88 headlight ECU sub-assembly LH connector.


b.

Connect the BB6 headlight cord LH connector.


c.

Connect the BB8 headlight cord RH connector.


d.

Disconnect the C headlight unit assembly LH connector.


Procedure1

e.

Measure the resistance according to the value(s) in the table below.

E401599C09
1.156,0.677 1.51,0.906 0.354,0.229 3.417,0.677 3.771,0.906 0.354,0.229 5.719,0.677 6.073,0.906 0.354,0.229 3.938,2.26 3.781,1.885 false 2.083,2.354 1.979,1.833 false 0.354,0.698 0.667,0.896 0.313,0.198 10 false *a 2.667,0.635 2.979,0.833 0.313,0.198 10 false *a 4.802,0.635 5.115,0.833 0.313,0.198 10 false *b 1.292,0.708 1.604,0.906 0.313,0.198 10 false B 3.552,0.708 3.865,0.906 0.313,0.198 10 false C 5.885,0.708 6.198,0.906 0.313,0.198 10 false F 3.813,2.292 4.583,2.49 0.771,0.198 10 false LIN1_1 2.042,2.375 2.813,2.573 0.771,0.198 10 false LINL
*a Component without harness connected
(to Headlight ECU Sub-assembly LH)
*b Component without harness connected
(to Headlight Leveling Motor LH)


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B89)Location & Routing

Click Connector(B89)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly RH

C-12 (LIN1_1) - B89-20 (LINL) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

f.

None



OK

107.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

107.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH

Pre-procedure1

a.

Disconnect the B88 headlight ECU sub-assembly LH connector.


b.

Connect the B89 headlight ECU sub-assembly RH connector.


c.

Disconnect the C headlight unit assembly RH connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

E401599C09
1.156,0.677 1.51,0.906 0.354,0.229 3.417,0.677 3.771,0.906 0.354,0.229 5.719,0.677 6.073,0.906 0.354,0.229 3.938,2.26 3.781,1.885 false 2.083,2.354 1.979,1.833 false 0.354,0.698 0.667,0.896 0.313,0.198 10 false *a 2.667,0.635 2.979,0.833 0.313,0.198 10 false *a 4.802,0.635 5.115,0.833 0.313,0.198 10 false *b 1.292,0.708 1.604,0.906 0.313,0.198 10 false B 3.552,0.708 3.865,0.906 0.313,0.198 10 false C 5.885,0.708 6.198,0.906 0.313,0.198 10 false F 3.813,2.292 4.583,2.49 0.771,0.198 10 false LIN1_1 2.042,2.375 2.813,2.573 0.771,0.198 10 false LINL
*a Component without harness connected
(to Headlight ECU Sub-assembly RH)
*b Component without harness connected
(to Headlight Leveling Motor RH)


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B89)Location & Routing

Click Connector(B89)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Headlight ECU Sub-Assembly RH

C-12 (LIN1_1) - B89-20 (LINL) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

e.

None



OK

108.INSPECT HEADLIGHT UNIT ASSEMBLY RH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

108.INSPECT HEADLIGHT UNIT ASSEMBLY RH

Pre-procedure1

a.

Remove the headlight unit assembly RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

E401599C07
1.156,0.677 1.51,0.906 0.354,0.229 3.417,0.677 3.771,0.906 0.354,0.229 5.719,0.677 6.073,0.906 0.354,0.229 3.938,2.26 3.781,1.885 false 1.938,2.198 1.833,1.677 false 1.385,2.177 1.677,1.844 false 0.354,0.698 0.667,0.896 0.313,0.198 10 false *a 2.667,0.635 2.979,0.833 0.313,0.198 10 false *a 4.802,0.635 5.115,0.833 0.313,0.198 10 false *b 1.292,0.708 1.604,0.906 0.313,0.198 10 false B 3.552,0.708 3.865,0.906 0.313,0.198 10 false C 5.885,0.708 6.198,0.906 0.313,0.198 10 false F 3.813,2.292 4.583,2.49 0.771,0.198 10 false LIN1_1 1.802,2.229 2.573,2.427 0.771,0.198 10 false ACTB 1.198,2.208 1.969,2.406 0.771,0.198 10 false ACTG
*a Component without harness connected
(to Headlight ECU Sub-assembly RH)
*b Component without harness connected
(to Headlight Leveling Motor RH)


Standard Resistance:
Tester Connection Condition Specified Condition
C-12 (LIN1_1) - F-3 Always Below 1 Ω
B-9 (ACTB) - F-1 Always Below 1 Ω
B-18 (ACTG) - F-4 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

109.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPLACE HEADLIGHT UNIT ASSEMBLY RH

109.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH

Pre-procedure1

a.

Connect all of the disconnected connectors.


b.

Disconnect the headlight leveling motor RH connector.


Procedure1

c.
E378482C13
1.458,0.417 1.938,0.635 0.479,0.219 0.115,0.104 0.427,0.26 0.313,0.156 10 false *a 1.677,0.458 1.99,0.615 0.313,0.156 10 false F
*a Component without harness connected
(to Headlight Leveling Motor RH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F-1 - F-4 Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE HEADLIGHT LEVELING MOTOR RH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH