The headlight ECU sub-assembly sends the control signal to the light control LED ECU via LIN communication to control the LED array.
The light control LED ECU supplies boosted voltage at a certain current to the LED array and turns on/off each LED according to the adaptive high beam system control.
By monitoring the LED power supply voltage, abnormal current malfunctions can be detected.
The light control LED ECU also detects malfunctions in the switching circuit for the adaptive high beam system.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B249200 | AHS Driver LH Malfunction |
Detection condition:
All of the following conditions are met:
-
Ignition switch ON
-
High beam headlights on
Malfunction status:
Adaptive high beam system circuit malfunction signals are received from the light control LED ECU LH
-
LED array malfunctioning
-
Light control LED ECU LH malfunctioning
-
Open circuit or short circuit in adaptive high beam system
Malfunction duration:
- |
·
Headlight unit assembly LH
·
Headlight unit LH
·
Light control LED ECU LH |
Headlight Control | A |
| B249300 | AHS Driver RH Malfunction |
Detection condition:
All of the following conditions are met:
-
Ignition switch ON
-
High beam headlights on
Malfunction status:
Adaptive high beam system circuit malfunction signals are received from the light control LED ECU RH
-
LED array malfunctioning
-
Light control LED ECU RH malfunctioning
-
Open circuit or short circuit in adaptive high beam system
Malfunction duration:
- |
·
Headlight unit assembly RH
·
Headlight unit RH
·
Light control LED ECU RH |
Headlight Control | A |
for LHD
for RHD
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON.
Operate the light control switch to turn on the high beam headlights.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B249200 and B249300 are not output | A |
| B249200 is output | B |
| B249300 is output | C |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Pre-procedure1
Remove the headlight unit assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY
Procedure1
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected (to Light Control LED ECU LH) |
*b | Component without harness connected (to Headlight Unit LH) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D-15 (LED11) - E-12 | Always | Below 1 Ω |
| D-3 (LED10) - E-1 | Always | Below 1 Ω |
| D-16 (LED9) - E-13 | Always | Below 1 Ω |
| D-4 (LED8) - E-2 | Always | Below 1 Ω |
| D-17 (LED7) - E-14 | Always | Below 1 Ω |
| D-5 (LED6) - E-3 | Always | Below 1 Ω |
| D-18 (LED5) - E-15 | Always | Below 1 Ω |
| D-6 (LED4) - E-4 | Always | Below 1 Ω |
| D-19 (LED3) - E-16 | Always | Below 1 Ω |
| D-7 (LED2) - E-5 | Always | Below 1 Ω |
| D-20 (LED1) - E-17 | Always | Below 1 Ω |
| D-8 (LED0) - E-6 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Set the Toyota Electrical Tester to diode check mode.
If the tester display is below 3 V, replace the dry cell batteries inside the tester.
Procedure1
Add 1 dry cell battery (about 1.5 V) between the Toyota Electrical Tester and inspection terminal and check if the LED illuminates.
| *1 | Dry Cell Battery | - | - |
| *a | Component without harness connected (to Light Control LED ECU LH) |
- | - |
| Tester Connection | Specified Condition |
|---|---|
| Tester positive (+) - D-15 (LED11) Tester negative (-) - D-3 (LED10) |
LED illuminates |
| Tester positive (+) - D-3 (LED10) Tester negative (-) - D-16 (LED9) |
LED illuminates |
| Tester positive (+) - D-16 (LED9) Tester negative (-) - D-4 (LED8) |
LED illuminates |
| Tester positive (+) - D-4 (LED8) Tester negative (-) - D-17 (LED7) |
LED illuminates |
| Tester positive (+) - D-17 (LED7) Tester negative (-) - D-5 (LED6) |
LED illuminates |
| Tester positive (+) - D-5 (LED6) Tester negative (-) - D-18 (LED5) |
LED illuminates |
| Tester positive (+) - D-18 (LED5) Tester negative (-) - D-6 (LED4) |
LED illuminates |
| Tester positive (+) - D-6 (LED4) Tester negative (-) - D-19 (LED3) |
LED illuminates |
| Tester positive (+) - D-19 (LED3) Tester negative (-) - D-7 (LED2) |
LED illuminates |
| Tester positive (+) - D-7 (LED2) Tester negative (-) - D-20 (LED1) |
LED illuminates |
| Tester positive (+) - D-20 (LED1) Tester negative (-) - D-8 (LED0) |
LED illuminates |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Remove the headlight unit assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY
Procedure1
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected (to Light Control LED ECU RH) |
*b | Component without harness connected (to Headlight Unit RH) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D-15 (LED11) - E-12 | Always | Below 1 Ω |
| D-3 (LED10) - E-1 | Always | Below 1 Ω |
| D-16 (LED9) - E-13 | Always | Below 1 Ω |
| D-4 (LED8) - E-2 | Always | Below 1 Ω |
| D-17 (LED7) - E-14 | Always | Below 1 Ω |
| D-5 (LED6) - E-3 | Always | Below 1 Ω |
| D-18 (LED5) - E-15 | Always | Below 1 Ω |
| D-6 (LED4) - E-4 | Always | Below 1 Ω |
| D-19 (LED3) - E-16 | Always | Below 1 Ω |
| D-7 (LED2) - E-5 | Always | Below 1 Ω |
| D-20 (LED1) - E-17 | Always | Below 1 Ω |
| D-8 (LED0) - E-6 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Set the Toyota Electrical Tester to diode check mode.
If the tester display is below 3 V, replace the dry cell batteries inside the tester.
Procedure1
Add 1 dry cell battery (about 1.5 V) between the Toyota Electrical Tester and inspection terminal and check if the LED illuminates.
| *1 | Dry Cell Battery | - | - |
| *a | Component without harness connected (to Light Control LED ECU RH) |
- | - |
| Tester Connection | Specified Condition |
|---|---|
| Tester positive (+) - D-15 (LED11) Tester negative (-) - D-3 (LED10) |
LED illuminates |
| Tester positive (+) - D-3 (LED10) Tester negative (-) - D-16 (LED9) |
LED illuminates |
| Tester positive (+) - D-16 (LED9) Tester negative (-) - D-4 (LED8) |
LED illuminates |
| Tester positive (+) - D-4 (LED8) Tester negative (-) - D-17 (LED7) |
LED illuminates |
| Tester positive (+) - D-17 (LED7) Tester negative (-) - D-5 (LED6) |
LED illuminates |
| Tester positive (+) - D-5 (LED6) Tester negative (-) - D-18 (LED5) |
LED illuminates |
| Tester positive (+) - D-18 (LED5) Tester negative (-) - D-6 (LED4) |
LED illuminates |
| Tester positive (+) - D-6 (LED4) Tester negative (-) - D-19 (LED3) |
LED illuminates |
| Tester positive (+) - D-19 (LED3) Tester negative (-) - D-7 (LED2) |
LED illuminates |
| Tester positive (+) - D-7 (LED2) Tester negative (-) - D-20 (LED1) |
LED illuminates |
| Tester positive (+) - D-20 (LED1) Tester negative (-) - D-8 (LED0) |
LED illuminates |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG