The door control receiver receives a signal from the electrical key transmitter sub-assembly and sends signals to the main body ECU (multiplex network body ECU) through the certification ECU (smart key ECU assembly) via CAN communication system. The certification ECU (smart key ECU assembly) sends door lock/unlock commands to the main body ECU (multiplex network body ECU).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B124296 | Wireless Door Lock Tuner Component Internal Failure | One of the following conditions is met:
·
Short in RDAM between the certification ECU (smart key ECU assembly) and door control receiver.
·
Short in RCO between the certification ECU (smart key ECU assembly) and door control receiver. |
·
Door control receiver
·
Certification ECU (smart key ECU assembly)
·
Harness or connector |
Entry&Start | A |
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Entry & Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
If the certification ECU (smart key ECU assembly) is replaced, refer to Service Bulletin.
When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, entry and start function and wireless control function performance may be affected.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
This DTC is not stored within 10 seconds of the ignition switch being turned from ON to off.
When replacing the door control receiver, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the GTS and write them down before removal.
It is necessary to perform initialization after registration of the transmitter IDs into the door control receiver if the door control receiver has been replaced. (for 12 Pin Type)
for initialization:
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION
for registration:
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION
Pre-Procedure 1
Disconnect the T21*1 or T12*2 door control receiver connector.
*1: for 12 Pin Type
*2: for 5 Pin Type
Procedure 1
Measure the voltage and resistance and check for pulses according to the value(s) in the table below.
| *a | Component with harness connected (Certification ECU (Smart Key ECU Assembly)) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I38,I39)Location & Routingewd_type=routing;type=c,c;code=I38,I39 |
||
| I38-11 (RDAM) - I39-29 (E) | Always | 11 to 14 V |
| I38-21 (RCO) - I39-29 (E) | Always | Pulse generation at regular intervals (Below 1 V ←→ 4.5 to 5.5 V) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I39)Location & Routingewd_type=routing;type=c;code=I39 |
||
| I39-29 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-Procedure 1
None
OK
NG
Pre-Procedure 1
Disconnect the I38 certification ECU (smart key ECU assembly) connector.
Disconnect the T21*1 or T12*2 door control receiver connector.
*1: for 12 Pin Type
*2: for 5 Pin Type
Procedure 1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I38,T21)Location & Routingewd_type=routing;type=c,c;code=I38,T21 Click Connector(T21)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Electrical Key & Tire Pressure Monitoring System Receiver Assemblyewd_type=component;type=c;code=T21;pinno=2,8,12 |
||
| I38-11 (RDAM) - T21-2 (DATA) | Always | Below 1 Ω |
| I38-21 (RCO) - T21-8 (+5) | Always | Below 1 Ω |
| T21-12 (GND) - Body ground | Always | Below 1 Ω |
| T21-2 (DATA) or I38-11 (RDAM) - Other terminals and body ground | Always | 10 kΩ or higher |
| T21-8 (+5) or I38-21 (RCO) - Other terminals and body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I38,T12)Location & Routingewd_type=routing;type=c,c;code=I38,T12 Click Connector(T12)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Smart Door Control Receiver Assemblyewd_type=component;type=c;code=T12;pinno=5,4,1 |
||
| I38-11 (RDAM) - T12-5 (DATA) | Always | Below 1 Ω |
| I38-21 (RCO) - T12-4 (+5) | Always | Below 1 Ω |
| T12-1 (GND) - Body ground | Always | Below 1 Ω |
| T12-5 (DATA) or I38-11 (RDAM) - Other terminals and body ground | Always | 10 kΩ or higher |
| T12-4 (+5) or I38-21 (RCO) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-Procedure 1
None
OK
NG