Description of "Communication Bus Check" Screen
The following communication bus check screen is provided only as an example. This screen differs from the actual screen for this vehicle.
The ECUs and sensors that are normally connected to the CAN communication system are displayed on the GTS.
Select "Communication Bus Check" on the menu screen of the GTS.
If items are not selected correctly in the vehicle specification pop up screen, the name of the CAN junction connector to which the ECUs or sensors are connected may not be displayed on the "Communication Bus Check" screen.
Confirm that the "Communication Bus Check" screen is displayed and the ECUs and sensors that are normally connected to the CAN communication system are displayed.
Even if an ECU or sensor that is connected to a bus that is monitored by a bus monitoring ECU (gateway function equipped ECU) is not communicating, it will remain displayed on the "Communication Bus Check" screen.
When an ECU or sensor that is connected to a bus that is not monitored by a bus monitoring ECU (gateway function equipped ECU) is not displayed on the "Communication Bus Check" screen, it means that it is not communicating.
The default display setting selected on the combo box is ALL. When checking for ECUs or sensors for a specific bus, choose the bus from the drop down list. ALL, each bus, each sub bus and Central Gateway are listed in the drop down list.
| *a | Combo box | *b | Background color is red or yellow |
| Item | Detail |
|---|---|
| Combo box: ALL | Displays all ECUs and sensors connected to the central bus and sub buses. |
| Combo box: Bus | Displays ECUs and sensors connected to the selected bus. |
| Combo box: Sub bus | Displays ECUs and sensors connected to the selected sub bus. |
| Combo box: Central Gateway | Displays all ECUs and sensors connected to the central bus. |
When using the combo box, it may be possible to select a sub bus from the drop down list that does not have any connected ECUs or sensors. This is not a malfunction and occurs when there is no optional device connected to a sub bus which is monitored by a sub bus monitoring ECU (gateway function equipped ECU).
In the drop down list, all sub buses applicable to the model are displayed (e.g. LIN communication sub buses are also displayed). For information on sub buses necessary to diagnose the CAN communication system, refer to System Diagram.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>SYSTEM DIAGRAM
The background color of an ECU or sensor changes according to its connection status as indicated in the following table.
| Bus Type | Background Color | Connection Status |
|---|---|---|
| Bus | White | Communication has been normal. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Currently not communicating (either of the following):
·
Not communicating since the start of the CAN bus check
·
Communication occurred at least once since the start of the CAN bus check, but is currently not occurring. |
|
| Not displayed | Either of the following:
·
The central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS.*4
·
No ECUs or sensors are connected to the bus.*5 |
|
| Sub bus with a gateway function equipped ECU that does not memorize connected ECUs or sensors*2 | White | Communication has been normal since the start of the CAN bus check. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Communication occurred at least once since the start of the CAN bus check, but is currently not occurring. | |
| Not displayed | Communication stop has continued since the start of the CAN bus check.*1 | |
| Sub bus with a gateway function equipped ECU that memorizes connected ECUs and sensors*3 | White | Communication has been normal. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Currently not communicating (either of the following):
·
Not communicating since the start of the CAN bus check
·
Communication occurred at least once since the start of the CAN bus check, but is currently not occurring. |
|
| Not displayed | Either of the following:
·
The gateway function equipped ECU cannot communicate with the central gateway ECU.*6
·
No ECUs or sensors are connected to the sub bus.*7 |
Gateway function equipped ECUs relay signals between ECUs and sensors connected to different buses.
*1: An ECU or sensor is installed to the vehicle but is not displayed on the "Communication Bus Check" screen.
*2: the gateway function equipped ECU does not memorize ECUs and sensors connected to its respective sub bus.
*3: the gateway function equipped ECU memorizes ECUs and sensors connected to its respective sub bus.
*4: When the central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS, the name of buses, sub buses, ECUs and sensors will not be displayed.
*5: When no ECUs or sensors are connected to a bus, the message "There is no system found on the communication Bus." will be displayed.
*6: When a gateway function equipped ECU cannot communicate with the central gateway ECU (network gateway ECU), the name of sub buses and ECUs or sensors connected to the sub bus will not be displayed.
*7: When no ECUs or sensors are connected to the sub bus, the message "There is no system found on the communication Bus." will be displayed.
If there is no communication between the GTS and the vehicle, or no ECUs or sensors are displayed as connected, check the central gateway ECU (network gateway ECU) and diagnosis bus (The bus that connects the DLC3 to the central gateway ECU (network gateway ECU)) for malfunctions.
Monitor the screen for any ECU or sensor connection status changes for a period of 2 minutes.
If an open occurs in one of the wires of a CAN branch line, it may interfere with the communication of other ECUs or sensors resulting in an incorrect state being displayed.
If the connection status changes intermittently during the inspection, repair the open in the branch line of the ECU or sensor that is not communicating, and then perform Communication Bus Check again.
Description of "Communication Bus Check (Detail)" Screen
The following communication bus check screen is provided only as an example. This screen differs from the actual screen for this vehicle.
The communication error history of ECUs or sensors which have communication error history can be displayed on the "Communication Bus Check (Detail)" screen.
Select "Communication Bus Check" on the menu screen of the GTS.
If items are not selected correctly in the vehicle specification pop up screen, the name of the CAN junction connector to which the ECUs or sensors are connected may not be displayed on the "Communication Bus Check" screen.
Select "Detail" on the "Communication Bus Check" screen.
| *a | Communication Bus Check (Detail) | - | - |
Confirm that the "Communication Bus Check (Detail)" screen is displayed and the communication error history of the ECUs or sensors up to present is displayed.
Lost Communication Time and Lost Communication Trip are only displayed for the central bus.
Lost Communication Time and Lost Communication Trip are not displayed for sub buses.
The default display setting selected on the combo box is ALL. When checking for ECUs or sensors for a specific bus, choose the bus from the drop down list. ALL, each bus, each sub bus and Central Gateway are listed in the drop down list.
| *a | Combo box | *b | Background color is red |
| Item | Detail |
|---|---|
| Combo box: ALL | Displays all ECUs and sensors connected to the central bus and sub buses. |
| Combo box: Bus | Displays ECUs and sensors connected to the selected bus. |
| Combo box: Sub bus | Displays ECUs and sensors connected to the selected sub bus. |
| Combo box: Central Gateway | Displays all ECUs and sensors connected to the central bus. |
| Bus Monitoring ECU | Displays the gateway function equipped ECU which monitors the selected bus or sub bus. |
| Current Trip | Displays the total number of trips up to now* |
| Lost Communication Time(s) | Displays the longest period of time in seconds that the ECU or sensor connected to the central bus was not communicating. |
| Lost Communication Trip | Displays the trip in which the longest period of time that the ECU or sensor connected to the central bus was not communicating occurred. |
*: If the component has been replaced with a new one, the total number of trips after the replacement is displayed.
The Lost Communication Time column displays the longest period of time in seconds that the central gateway ECU (network gateway ECU) detected a communication stop in the respective ECU or sensor.
The Lost Communication Trip column displays the trip in which the central gateway ECU (network gateway ECU) detected the longest communication stop in the respective ECU or sensor.
When using the combo box, it may be possible to select a sub bus from the drop down list that does not have any connected ECUs or sensors. This is not a malfunction and occurs when there is no optional device connected to a sub bus which is monitored by a sub bus monitoring ECU (gateway function equipped ECU).
In the drop down list, all sub buses applicable to the model are displayed (e.g. LIN communication sub buses are also displayed). For information on sub buses necessary to diagnose CAN communication system, refer to the System Diagram.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>SYSTEM DIAGRAM
The background color of an ECU or sensor changes according to its connection status as indicated in the following table.
| Bus Type | Background Color | Connection Status |
|---|---|---|
| Bus | White | Either of the following:
·
Communication has been normal.
·
Lost Communication Time is below 6 seconds. |
| Red | Lost Communication Time is 6 seconds or more. | |
| Not displayed | Either of the following:
·
The central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS.*1
·
No ECUs or sensors are connected to the bus.*2 |
|
| Sub bus | White | Lost Communication Time is displayed as "-". |
| Not displayed | Either of the following:
·
The gateway function equipped ECU cannot communicate with the central gateway ECU.*3
·
No ECUs or sensors are connected to the sub bus.*4 |
If there is no communication between the GTS and the vehicle, or no ECUs or sensors are displayed as connected, check the central gateway ECU (network gateway ECU) and diagnosis bus (The bus that connects the DLC3 to the central gateway ECU (network gateway ECU)) for malfunctions.
Lost Communication Time and Lost Communication Trip are not displayed for sub buses.
*1: When the central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS, the name of buses, sub buses, ECUs and sensors will not be displayed.
*2: When no ECUs or sensors are connected to a bus, the message "There is no system found on the communication Bus." will be displayed.
*3: When a gateway function equipped ECU cannot communicate with the central gateway ECU (network gateway ECU), the name of sub buses and ECUs or sensors connected to the sub bus will not be displayed.
*4: When no ECUs or sensors are connected to the sub bus, the message "There is no system found on the communication Bus." will be displayed.
Communication Bus Check (Communication Malfunction Check)
DTCs related to CAN communication are displayed for each ECU on the GTS.
Select "Communication Bus Check" on the menu screen of the GTS.
Select "Communication Malfunction Check" on the "Communication Bus Check" screen.
| *a | Communication Malfunction Check | - | - |
Confirm that the "Communication Malfunction Check" screen is displayed and CAN communication DTCs for each ECU are displayed.
When there are no CAN communication DTCs stored, no DTCs will be displayed.
How to Use "Communication Bus Check" Screen in Inspection
The following CAN bus wiring diagram or communication bus check screen is provided only as an example. This wiring diagram or screen differs from the actual one for this vehicle.
If the CAN communication system is currently malfunctioning, it is recommended to use Communication Bus Check rather than Communication DTCs for determining the suspected area.
Turn the ignition switch to ON, or perform the necessary operations to reproduce the problem symptom, select "Communication Bus Check" and wait approximately 2 minutes. Check the communication status of each ECU or sensor on the screen while performing this operation.
If the CAN communication system is currently malfunctioning, determine the suspected area through Communication Bus Check as follows:
| Problem Symptom Pattern | Display on Communication Bus Check Screen | Suspected Area |
|---|---|---|
| A | Almost all of the ECUs and sensors connected to the malfunctioning CAN bus are displayed as not communicating on the "Communication Bus Check" screen. |
·
Short between CAN bus lines (CANH and CANL)
·
Short to +B in a CAN bus line (CANH or CANL)
·
Short to ground in a CAN bus line (CANH or CANL) |
| B | ECUs or sensors farther from the central gateway ECU (network gateway ECU) than the open in the wires are displayed as not communicating on the "Communication Bus Check" screen. | Open in both wires of a main bus line in the central bus |
| C | One ECU or sensor is displayed as not communicating on the "Communication Bus Check" screen. |
·
Open in both wires of a branch line connected to an ECU or sensor in the central bus
·
Internal malfunction of an ECU or sensor in the central bus
·
Malfunction in the power supplied to an ECU or sensor in the central bus |
| D | No ECUs or sensors are displayed on the "Communication Bus Check" screen. |
·
Internal malfunction of the central gateway ECU (network gateway ECU)
·
Malfunction in the power supplied to the central gateway ECU (network gateway ECU)
·
Open in both wires of the branch line in the diagnosis bus (DLC3 - Central gateway ECU (network gateway ECU))
·
Short between CAN bus lines (CANH and CANL) in the diagnosis bus (DLC3 - Central gateway ECU (network gateway ECU))
·
Short to +B in a CAN bus line (CANH or CANL) in the diagnosis bus (DLC3 - Central gateway ECU (network gateway ECU))
·
Short to ground in a CAN bus line (CANH or CANL) in the diagnosis bus (DLC3 - Central gateway ECU (network gateway ECU)) |
| E | One ECU or sensor is displayed as not communicating in multiple buses on the "Communication Bus Check" screen. |
·
Internal malfunction of an ECU or sensor connected to multiple buses
·
Malfunction in the power supplied to an ECU or sensor connected to multiple buses |
| F | Some ECUs or sensors are displayed as not communicating in the central bus and other ECUs or sensors are displayed as not communicating in a sub bus. |
·
Open in a wire of a branch line connected to an ECU or sensor in the central bus
·
Internal malfunction of an ECU or sensor in the central bus |
| G | A gateway function equipped ECU is displayed as not communicating in the central bus and ECUs and sensors connected to its respective sub bus are not displayed. |
·
Open in both wires of a branch line connected to a gateway function equipped ECU
·
Internal malfunction of a gateway function equipped ECU
·
Malfunction in the power supplied to a gateway function equipped ECU |
| H | One ECU or sensor is displayed as not communicating in a sub bus on the "Communication Bus Check" screen. |
·
Open in both wires of a branch line connected to an ECU or sensor in a sub bus
·
Internal malfunction of an ECU or sensor in a sub bus
·
Malfunction in the power supplied to an ECU or sensor in a sub bus |
| I | ECUs or sensors farther from the sub bus monitoring ECU (gateway function equipped ECU) than the open in the wires are displayed as not communicating on the "Communication Bus Check" screen. | Open in both wires of a main bus line in a sub bus |
Problem Symptom Pattern A
| Details of Malfunction |
·
Short between CAN bus lines (CANH and CANL) in Bus 2
·
Short to +B in a CAN bus line (CANH or CANL) in Bus 2
·
Short to ground in a CAN bus line (CANH or CANL) in Bus 2 |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
Due to the malfunction, almost all of the ECUs and sensors connected to Bus 2 will be displayed as not communicating and their background color will be red.
The malfunction in Bus 2 will not affect the other buses.
The malfunctioning part can be determined by inspecting for an open in the main bus line, a short between bus lines or a short to +B or ground.
Make sure to perform the inspection to measure resistances of buses to determine the cause of the malfunction.
| Details of Malfunction |
·
Short between CAN bus lines (CANH and CANL) in Bus 4
·
Short to +B in a CAN bus line (CANH or CANL) in Bus 4
·
Short to ground in a CAN bus line (CANH or CANL) in Bus 4 |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
| *g | Not displayed | - | - |
Due to the malfunction, almost all of the ECUs and sensors connected to Bus 4 will be displayed as not communicating and their background color will be red.
The malfunction will not affect the other buses of the central bus. However, the sub bus connected to Bus 4 is likely to be affected. the gateway function equipped ECU connected to Bus 4 will not communicate and consequently the sub bus and its respective ECUs or sensors monitored by the gateway function equipped ECU (sub bus monitoring ECU) will not be displayed, indicating that the gateway function equipped ECU is not communicating with the central gateway ECU (network gateway ECU).
The malfunctioning part can be determined by inspecting for an open in the main bus line, a short between bus lines or a short to +B or ground.
Make sure to perform the inspection to measure resistances of buses to determine the cause of the malfunction.
Problem Symptom Pattern B
| Details of Malfunction | Open in both wires of the main bus line between the CGW and No. 1 CAN junction connector in Bus 2 |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
Due to the malfunction, almost all of the ECUs and sensors connected to Bus 2 will be displayed as not communicating and their background color will be red.
The malfunction in Bus 2 will not affect the other buses.
The malfunctioning part can be determined by inspecting for an open in the main bus line.
Make sure to perform the inspection to measure resistances of buses to determine the cause of the malfunction.
| Details of Malfunction | Open in both wires of the main bus line between the No. 1 CAN junction connector and No. 2 CAN junction connector in Bus 2 |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
Due to the malfunction, ECUs or sensors farther from the CGW than the open in the wires will be displayed as not communicating and their background color will be red.
The malfunction in Bus 2 will not affect the other buses.
The malfunctioning part can be determined by inspecting for an open in the main bus line.
Make sure to perform the inspection to measure resistances of buses to determine the cause of the malfunction.
| Details of Malfunction | Open in both wires of the main bus line between the No. 2 CAN junction connector and ENG in Bus 2 |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
| *g | Pattern 1 | *h | Pattern 2 |
Even when the same part of the main bus line is open, depending on internal electrical noise which changes according to the position of the open in the line, the information displayed on the "Communication Bus Check" screen may differ.
In pattern 2, the information displayed may be the same as when there is an open in both wires in the main bus line between the No. 1 CAN junction connector and No. 2 CAN junction connector, which may make it difficult to determine the malfunctioning part.
The malfunction in Bus 2 will not affect the other buses.
Make sure to perform the inspection to measure resistances of buses to determine the cause of the malfunction.
Problem Symptom Pattern C
| Details of Malfunction | Open in both wires of the branch line connected to F-MGC in Bus 2 |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
The information displayed on the "Communication Bus Check" screen will be the same for an open in both wires of a branch line, an internal malfunction of an ECU or sensor or a malfunction in the power supplied to an ECU or sensor. In this example, the background color of the malfunctioning ECU or sensor will be red.
| Details of Malfunction |
·
Internal malfunction of F-MGC in Bus 2
·
Malfunction in the power supplied to F-MGC in Bus 2 |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
The information displayed on the "Communication Bus Check" screen will be the same for an open in both wires of a branch line, an internal malfunction of an ECU or sensor or a malfunction in the power supplied to an ECU or sensor. In this example, the background color of the malfunctioning ECU or sensor will be red.
| Details of Malfunction | Open in both wires of the branch line connected to ENG in Bus 4 |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
The malfunction in Bus 4 will not affect the other buses.
Due to the malfunction, although ENG is communicating normally with CGW via Bus 2, it is not communicating with CGW via Bus 4. Consequently, it will be displayed as not communicating in Bus 4.
Problem Symptom Pattern D
| Details of Malfunction |
·
Internal malfunction of the CGW
·
Malfunction in the power supplied to the CGW |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Not displayed |
When there is no communication between the GTS and the vehicle, no ECUs or sensors will be displayed.
| Details of Malfunction | Open in both wires of the branch lines in the diagnosis bus |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Not displayed |
When there is no communication between the GTS and the vehicle, no ECUs or sensors will be displayed.
Problem Symptom Pattern E
| Details of Malfunction |
·
Internal malfunction of BRK
·
Malfunction in the power supplied to BRK |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
The information displayed on the "Communication Bus Check" screen will be the same for an internal malfunction of an ECU or sensor, or a malfunction in the power supplied to an ECU or sensor.
Due to the malfunction, BRK is not communicating with the CGW via both Bus 2 and Bus 4. Consequently, the background color of BRK will be red for both Bus 2 and Bus 4.
Problem Symptom Pattern F
| Details of Malfunction |
·
Open in a wire of the branch line connected to HV in Bus 4
·
Internal malfunction of HV in Bus 4 |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
| *g | Background color intermittently becomes yellow or red | *h | Not displayed or background color is yellow or red |
In the "Communication Bus check" screen shown in the illustration, electrical noise in the CAN bus caused by an open in a wire in the branch line connected to HV interferes with the communication of MB causing unstable communication. Also, since MB is a gateway function equipped ECU, communication of ECUs connected to its respective sub bus will also be unstable.
In the "Communication Bus Check" screen shown in the illustration, because the background color of HV is red, it is suspected that HV is the most likely cause of the malfunction. Therefore, it is suspected that HV is not communicating.
Problem Symptom Pattern G
| Details of Malfunction |
·
Open in both wires of the branch line connected to MB in Bus 4
·
Internal malfunction of MB in Bus 4
·
Malfunction in the power supplied to MB in Bus 4 |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
| *g | Not displayed | - | - |
If there is a communication malfunction in a gateway function equipped ECU, ECUs connected to its respective sub bus will also be affected and will not be displayed.
In the "Communication Bus Check" screen shown in the illustration, MB is a gateway function equipped ECU. Therefore, MB is suspected as not communicating.
Problem Symptoms Pattern H
| Details of Malfunction |
·
Internal malfunction of MIR-L in the sub bus
·
Malfunction in the power supplied to MIR-L in the sub bus |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
The malfunction in the sub bus will not affect the other buses.
When a gateway function equipped ECU memorizes ECUs and sensors connected to its respective sub bus and there is a communication malfunction in one of the ECUs or sensors, the background color of the ECU or sensor will change to red and the ECU or sensor will remain displayed.
The information displayed on the "Communication Bus Check" screen will be the same for an open in both wires of a branch line, an internal malfunction of an ECU or sensor or a malfunction in the power supplied to an ECU or sensor.
| Details of Malfunction | Open in both wires of the branch line connected to MIR-L in the sub bus |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
The malfunction in the sub bus will not affect the other buses.
When a gateway function equipped ECU memorizes ECUs and sensors connected to its respective sub bus and there is a communication malfunction in one of the ECUs or sensors, the background color of the ECU or sensor will change to red and the ECU or sensor will remain displayed.
The information displayed on the "Communication Bus Check" screen will be the same for an open in both wires of a branch line, an internal malfunction of an ECU or sensor or a malfunction in the power supplied to an ECU or sensor.
Problem Symptom Pattern I
| Details of Malfunction | Open in both wires of the main bus line in the sub bus |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
Due to the malfunction, ECUs or sensors farther from the sub bus monitoring ECU (gateway function equipped ECU) than the open in the wires will be displayed as not communicating and their background color will be red.
How to Use "Communication Bus check (Detail)" Screen in Inspection
If the CAN communication system is currently normal but has communication stop history, determine the malfunctioning part using Communication Bus Check (Detail) as follows:
The following CAN bus wiring diagram or communication bus check screen is provided only as an example. This wiring diagram or screen differs from the actual one for this vehicle.
The Lost Communication Time column displays the longest period of time in seconds that the central gateway ECU (network gateway ECU) detected a communication stop in the respective ECU or sensor.
The Lost Communication Trip column displays the trip in which the central gateway ECU (network gateway ECU) detected the longest communication stop in the respective ECU or sensor.
When using the combo box, it may be possible to select a sub bus from the drop down list that does not have any connected ECUs or sensors. This is not a malfunction and occurs when there is no optional device connected to a sub bus which is monitored by a sub bus monitoring ECU (gateway function equipped ECU).
In the drop down list, all sub buses applicable to the model are displayed (e.g. LIN communication sub buses are also displayed). For information on sub buses necessary to diagnose CAN communication system, refer to the System Diagram.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>SYSTEM DIAGRAM
If the CAN communication system is currently malfunctioning, it is recommended to use Communication Bus Check rather than Communication Bus Check (Detail) for determining the suspected area.
The communication error history of ECUs or sensors which have communication error history can be displayed on the "Communication Bus Check (Detail)" screen.
Lost Communication Time and Lost Communication Trip are only displayed for the central bus.
Lost Communication Time and Lost Communication Trip are not displayed for sub buses.
If there is an ECU or sensor displayed with a red background on the "Communication Bus Check (Detail)" screen to indicate that it was not communicating, it is suspected that the ECU or sensor was not communicating.
| Details of Malfunction | Past malfunction in the wire harness or power supplied to F-MGC in Bus 2 |
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub bus | *d | Diagnosis bus |
| *e | Location of malfunction | *f | Background color is red |
| Bus Type | Background Color | Connection Status |
|---|---|---|
| Bus | White | Either of the following:
·
Communication has been normal.
·
Lost Communication Time is below 6 seconds. |
| Red | Lost Communication Time is 6 seconds or more. | |
| Not displayed | Either of the following:
·
The central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS.*1
·
No ECUs or sensors are connected to the bus.*2 |
|
| Sub bus | White | Lost Communication Time is displayed as "-". |
| Not displayed | Either of the following:
·
The gateway function equipped ECU cannot communicate with the central gateway ECU.*3
·
No ECUs or sensors are connected to the sub bus.*4 |
Check the values of Lost Communication Trip and Current Trip for the ECUs or sensors that have a red background color.
If the values of Lost Communication Trip and Current Trip are the same for an ECU or sensor, the ECU or sensor is currently not communicating. In this case, it is recommended to use Communication Bus Check rather than Communication Bus Check (Detail) for determining the suspected area.
In the "Communication Bus Check (Detail)" screen shown in the illustration, F-MGC had a communication malfunction in the 10th trip. Thus, it is suspected that F-MGC was not communicating.
*1: When the central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS, the name of buses, sub buses, ECUs and sensors will not be displayed.
*2: When no ECUs or sensors are connected to a bus, the message "There is no system found on the communication Bus." will be displayed.
*3: When a gateway function equipped ECU cannot communicate with the central gateway ECU (network gateway ECU), the name of sub buses and ECUs or sensors connected to the sub bus will not be displayed.
*4: When no ECUs or sensors are connected to the sub bus, the message "There is no system found on the communication Bus." will be displayed.
DTC TABLE BY ECU
In the CAN communication system, the CAN communication DTCs of each ECU can be displayed using the GTS.
If CAN communication system DTCs are output, the malfunction cannot be determined only by the DTCs. Perform troubleshooting according to How to Proceed with Troubleshooting.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
If there is a malfunction currently, DTCs can be checked by performing steps in the DTC check procedure.
ECM / GTS Display "Engine"
DTC communication uses the CAN communication system.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U010187 | Lost Communication with Drive Motor Control Module "A" Missing Message | Communication stop occurs between the ECM and TCM continuously for approximately 2 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 1 second or more.
·
The power source voltage of the ECM is 10 V or higher. |
Turn the ignition switch to ON and wait for at least approximately 4 seconds. | The MIL (Check engine warning light) illuminates. | - | DTC is stored until it is cleared using the GTS. |
| U012987 | Lost Communication between Hybrid Powertrain Control Module and Active Grille Air Shutter Missing Message | Communication stop occurs between the ECM and brake actuator assembly (No.2 skid control ECU) continuously for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 2 seconds or more.
·
The power source voltage of the ECM is 10 V or higher. |
Turn the ignition switch to ON and wait for at least approximately 7 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U110387 | Lost Communication with Stop and Start Control Module | Communication stop occurs between the ECM and the engine stop and start ECU continuously for 2 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 1 second or more.
·
The power source voltage of the ECM is 10 V or higher. |
Turn the ignition switch to ON and wait for at least approximately 3 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
TCM / GTS Display "Transmission" (w/ Automatic Transmission System [for AJA0F])
DTC communication uses the CAN communication system.
| DTC | Detection Item | DTC Detection Condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | ||
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U012987 | Lost Communication with Brake System Control Module Missing Message | Communication stop occurs between the TCM and brake actuator assembly (No.2 skid control ECU) continuously for approximately 3 seconds or more. | All conditions are met:
·
Approximately 3 seconds or more elapse after the ignition switch is turned to ON.
·
The power source voltage of the TCM is 10 V or more. |
Turn the ignition switch to ON and wait at least approximately 6 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U010087 | Lost Communication with ECM/PCM "A" Missing Message | Communication stop occurs between the TCM and ECM continuously for 2 seconds or more. | All conditions are met:
·
Approximately 1 second or more elapse after the ignition switch is turned to ON.
·
The power source voltage of the TCM is 10 V or more. |
Turn the ignition switch to ON and wait at least approximately 2 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U110387 | Lost Communication with Stop and Start Control Module Missing Message | Communication stop occurs between the TCM and the engine stop and start ECU continuously for 1 second or more. | All conditions are met:
·
Approximately 1 second or more elapse after the ignition switch is turned to ON.
·
The power source voltage of the TCM is 10 V or more. |
Turn the ignition switch to ON and wait at least 2 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
Engine Stop and Start ECU / GTS Display "Stop and Start" (w/ Stop and Start System)
DTC communication uses the CAN communication system.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U010087 | Lost Communication with ECM/PCM "A" Missing Message | Communication stop occurs between the engine stop and start ECU and ECM continuously for 1 second or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the engine stop and start ECU is 10 V or more. |
Turn the ignition switch to ON and wait at least 5 seconds. | The ECO RUN blinks. | - | DTC is stored until it is cleared using the GTS. |
| U010187 | Lost Communication with TCM Missing Message | Communication stop occurs between the engine stop and start ECU and TCM continuously for approximately 1 second or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the engine stop and start ECU is 10 V or more. |
Turn the ignition switch to ON and wait at least approximately 5 seconds. | The ECO RUN blinks. | - | DTC is stored until it is cleared using the GTS. |
| U012687 | Lost Communication with Steering Angle Sensor Module Missing Message | Communication stop occurs between the engine stop and start ECU and steering sensor continuously for 3 second or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the engine stop and start ECU is 10 V or more. |
Turn the ignition switch to ON and wait at least 9 seconds. | The ECO RUN blinks. | - | DTC is stored until it is cleared using the GTS. |
| U012987 | Lost Communication with Brake System Control Module Missing Message | Communication stop occurs between the engine stop and start ECU and brake actuator assembly (No.2 skid control ECU) continuously for approximately 3 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the engine stop and start ECU is 10 V or more. |
Turn the ignition switch to ON and wait at least approximately 8 seconds. | The ECO RUN blinks. | - | DTC is stored until it is cleared using the GTS. |
| U013187 | Lost Communication with Power Steering Control Module Missing Message | Communication stop occurs between the engine stop and start ECU and the power steering ECU assembly continuously for 3 second or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the engine stop and start ECU is 10 V or higher. |
Turn the ignition switch to ON and wait at least 9 seconds. | The ECO RUN blinks. | - | DTC is stored until it is cleared using the GTS. |
| U014087 | Lost Communication with Body Control Module Missing Message | Communication stop occurs between the engine stop and start ECU and the main body ECU (multiplex network body ECU) continuously for approximately 4 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the engine stop and start ECU is 10 V or more. |
Turn the ignition switch to ON and wait at least approximately 11 seconds. | The ECO RUN blinks. | - | DTC is stored until it is cleared using the GTS. |
| U015187 | Lost Communication with Restraints Control Module Missing Message | Communication stop occurs between the engine stop and start ECU and airbag ECU assembly continuously for approximately 11 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the engine stop and start ECU is 10 V or higher. |
Turn the ignition switch to ON and wait at least approximately 25 seconds. | The ECO RUN blinks. | - | DTC is stored until it is cleared using the GTS. |
| U016487 | Lost Communication with HVAC Control Module Missing Message | Communication stop occurs between the engine stop and start ECU and air conditioning amplifier assembly continuously for approximately 11 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the engine stop and start ECU is 10 V or higher. |
Turn the ignition switch to ON and wait at least approximately 25 seconds. | The ECO RUN blinks. | - | DTC is stored until it is cleared using the GTS. |
| U015587 | Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message | Communication stop occurs between the engine stop and start ECU and combination meter assembly continuously for 4 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the engine stop and start ECU is 10 V or higher. |
Turn the ignition switch to ON and wait at least approximately 11 seconds. | The ECO RUN blinks. | - | DTC is stored until it is cleared using the GTS. |
| U111087 | Lost Communication with Clearance Sonar Module Missing Message | Communication stop occurs between the engine stop and start ECU and clearance warning ECU assembly continuously for approximately 3 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the engine stop and start ECU is 10 V or higher. |
Turn the ignition switch to ON and wait at least 9 seconds. | The ECO RUN blinks. | - | DTC is stored until it is cleared using the GTS. |
| U117087 | Lost Communication with Brake System Control Module (ch2) Missing Message | Communication stop occurs between the engine stop and start ECU and brake actuator assembly (No.2 skid control ECU) continuously for approximately 3 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the engine stop and start ECU is 10 V or higher. |
Turn the ignition switch to ON and wait at least approximately 8 seconds. | The ECO RUN blinks. | - | DTC is stored until it is cleared using the GTS. |
Brake Actuator Assembly (Skid Control ECU) / GTS Display "Brake/EPB*"
DTC communication uses the CAN communication system.
EPB*: Electric Parking Brake
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U007488 | Control Module Communication Bus "B" Off Bus Off | The brake actuator assembly (No. 2 skid control ECU) cannot send and receive data (The bus is off) for approximately 1 second or more. | All conditions are met:
·
3 seconds or more elapse after the ignition switch is turned to ON.
·
The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.6 V or higher. |
Turn the ignition switch to ON and wait at least approximately 4 seconds. |
·
The ABS warning light illuminates.
·
The slip indicator light illuminates.
·
The brake hold operated indicator light blinks.
·
The brake warning light (red) illuminates. |
Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U010087 | Lost Communication with ECM/PCM "A" Missing Message | Communication stop occurs between the brake actuator assembly (No. 2 skid control ECU) and ECM continuously for 2 seconds or more. | All conditions are met:
·
3 seconds or more elapse after the ignition switch is turned to ON.
·
The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.6 V or higher.
·
The vehicle speed is 6 km/h (4 mph) or more. |
Drive the vehicle for 5 seconds or more at a speed of 6 km/h (4 mph) or more. |
·
The slip indicator light illuminates.
·
The brake hold operated indicator light blinks.
·
The electric parking brake auto off indicator light illuminates. |
Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U010187 | Lost Communication with TCM Missing Message | Communication stop occurs between the brake actuator assembly (No. 2 skid control ECU) and TCM continuously for 2 seconds or more. | All conditions are met:
·
3 seconds or more elapse after the ignition switch is turned to ON.
·
The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.6 V or higher.
·
The vehicle speed is 6 km/h (4 mph) or more. |
Drive the vehicle for 5 seconds or more at a speed of 6 km/h (4 mph) or more. |
·
The slip indicator light illuminates.
·
The brake hold operated indicator light blinks.
·
The electric parking brake auto off indicator light illuminates. |
Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U012587 | Lost Communication with Multi-axis Acceleration Sensor Module Missing Message | Communication stop occurs between the brake actuator assembly (No. 2 skid control ECU) and airbag ECU assembly continuously for 1 second or more. | All conditions are met:
·
3 seconds or more elapse after the ignition switch is turned to ON.
·
The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.6 V or higher.
·
The vehicle speed is 6 km/h (4 mph) or more. |
Drive the vehicle for 4 seconds or more at a speed of 6 km/h (4 mph) or more. |
·
The slip indicator light illuminates.
·
The brake hold operated indicator light blinks.
·
The electric parking brake auto off indicator light illuminates. |
Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U012687 | Lost Communication with Steering Angle Sensor Module Missing Message | Communication stop occurs between the brake actuator assembly (No. 2 skid control ECU) and steering sensor continuously for 1 second or more. | All conditions are met:
·
3 seconds or more elapse after the ignition switch is turned to ON.
·
The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.6 V or higher.
·
The vehicle speed is 6 km/h (4 mph) or more. |
Drive the vehicle for 4 seconds or more at a speed of 6 km/h (4 mph) or more. |
·
The slip indicator light illuminates.
·
The brake hold operated indicator light blinks. |
Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U014087 | Lost Communication with Body Control Module Missing Message | Communication stop occurs between the brake actuator assembly (No. 2 skid control ECU) and main body ECU (multiplex network body ECU) continuously for 2 seconds or more. | All conditions are met:
·
3 seconds or more elapse after the ignition switch is turned to ON.
·
The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.6 V or higher.
·
The vehicle speed is 6 km/h (4 mph) or more. |
Drive the vehicle for 5 seconds or more at a speed of 6 km/h (4 mph) or more. |
·
The electric parking brake auto off indicator light illuminates.
·
The brake hold operated indicator light blinks. |
- | DTC is stored until it is cleared using the GTS. |
| U015187 | Lost Communication with Restraints Control Module Missing Message | Communication stop occurs between the brake actuator assembly (No. 2 skid control ECU) and airbag ECU assembly continuously for 5 seconds or more. | All conditions are met:
·
3 seconds or more elapse after the ignition switch is turned to ON.
·
The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.6 V or higher.
·
The vehicle speed is 6 km/h (4 mph) or more. |
Drive the vehicle for 8 seconds or more at a speed of 6 km/h (4 mph) or more. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U110387 | Lost Communication with Stop and Start Control Module Missing Message | Communication stop occurs between the brake actuator assembly (No. 2 skid control ECU) and the engine stop and start ECU continuously for 2 seconds or more. | All conditions are met:
·
3 seconds or more elapse after the ignition switch is turned to ON.
·
The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.6 V or higher.
·
The vehicle speed is 6 km/h (4 mph) or more. |
Drive the vehicle for 5 seconds or more at a speed of 6 km/h (4 mph) or more. |
·
The electric parking brake auto off indicator light illuminates.
·
The brake hold operated indicator light blinks. |
- | DTC is stored until it is cleared using the GTS. |
Radio and Display Receiver Assembly / GTS Display "Navigation System" (w/ Audio and Visual System (for Radio and Display Type, except 12.3 Inch Display))
DTC communication uses the CAN communication system.
ECB*: Electronically Controlled Brake System
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U0073 | Sending Malfunction (Navigation to APGS) | The radio and display receiver assembly is unable to send or receive data 10 times consecutively. | All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the radio and display receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least 61 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0100 | Engine/EV ECU Communication | The radio and display receiver assembly does not receive data from the ECM for 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the radio and display receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| The radio and display receiver assembly does not receive data from the ECM for 11 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 11 seconds or more.
·
The power source voltage of the radio and display receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least 22 seconds. | - | - | DTC is stored until it is cleared using the GTS. | ||
| The radio and display receiver assembly does not receive data from the ECM for 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for 10 seconds or more.
·
The power source voltage of the radio and display receiver assembly is 9.5 V.
·
The vehicle speed is 20 km/h (12 mph) or more. |
Drive the vehicle for 20 seconds or more at a speed of 20 km/h (12 mph) or more. | - | - | DTC is stored until it is cleared using the GTS. | ||
| U0129 | VSC(ECB)ECU Communication | The radio and display receiver assembly does not receive data from the brake actuator assembly (No. 2 skid control ECU) for 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for 10 seconds or more.
·
The power source voltage of the radio and display receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| All conditions are met:
·
The ignition switch is ON for 10 seconds or more.
·
The power source voltage of the radio and display receiver assembly is 9.5 V.
·
The vehicle speed is 20 km/h (12 mph) or more. |
Drive the vehicle for 20 seconds or more at a speed of 20 km/h (12 mph) or more. | - | - | DTC is stored until it is cleared using the GTS. | |||
| The radio and display receiver assembly does not receive data from the brake actuator assembly (No. 2 skid control ECU) for 4 seconds or more. | All conditions are met:
·
The ignition switch is ON for 10 seconds or more.
·
The power source voltage of the radio and display receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. | ||
| U0132 | Air Suspension ECU Communication | The radio and display receiver assembly does not receive data from the absorber control ECU for 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for 10 seconds or more.
·
The power source voltage of the radio and display receiver assembly is 9.5 V.
·
The vehicle speed is 20 km/h (12 mph) or more. |
Drive the vehicle for 20 seconds or more at a speed of 20 km/h (12 mph) or more. | - | - | DTC is stored until it is cleared using the GTS. |
| U0140 | Lost Communication with Body Control Module | The radio and display receiver assembly does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for 10 seconds or more.
·
The power source voltage of the radio and display receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Meter ECU Communication | The radio and display receiver assembly does not receive data from the main body ECU (multiplex network body ECU) for 30 seconds or more. | All conditions are met:
·
The ignition switch is ON for 30 seconds or more.
·
The power source voltage of the radio and display receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least 60 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0164 | Air Conditioner ECU Communication | The radio and display receiver assembly does not receive data from the air conditioning amplifier assembly for 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for 10 seconds or more.
·
The power source voltage of the radio and display receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least 20 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0198 | Lost Communication with Telematic Control Module | The radio and display receiver assembly does not receive data from the telephone transceiver assembly for 3 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the radio and display receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least 6 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0208 | Lost Communication with "Seat Control Module A" | The radio and display receiver assembly does not receive data from the position control ECU assembly for 15 seconds or more. | All conditions are met:
·
The ignition switch is ON for 15 seconds or more.
·
The power source voltage of the radio and display receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least 30 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0209 | Lost Communication with "Seat Control Module B" | The radio and display receiver assembly does not receive data from the position control ECU assembly for 15 seconds or more. | All conditions are met:
·
The ignition switch is ON for 15 seconds or more.
·
The power source voltage of the radio and display receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least 30 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U023B | Lost Communication with Image Processing Module "B" | The radio and display receiver assembly does not receive data from the parking assist ECU for approximately 12 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 12 seconds or more.
·
The power source voltage of the radio and display receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least approximately 24 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0265 | Lost Communication with Image Processing Sensor A | The radio and display receiver assembly does not receive data from the rear television camera assembly for approximately 12 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 12 seconds or more.
·
The power source voltage of the radio and display receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least approximately 24 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U1110 | Clearance Sonar ECU Communication | The radio and display receiver assembly does not receive data from the clearance warning ECU assembly for 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for 10 seconds or more.
·
The power source voltage of the radio and display receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
Radio Receiver Assembly / GTS Display "Navigation System" (w/ Audio and Visual System (for Radio and Display Type, for 12.3 Inch Display))
DTC communication uses the CAN communication system.
ECB*: Electronically Controlled Brake System
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U0073 | Sending Malfunction (Navigation to APGS) | The radio receiver assembly is unable to send or receive data 10 times consecutively. | All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the radio receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least 61 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0100 | Engine/EV ECU Communication | The radio receiver assembly does not receive data from the ECM for 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the radio receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| The radio receiver assembly does not receive data from the ECM for 11 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 11 seconds or more.
·
The power source voltage of the radio receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least 22 seconds. | - | - | DTC is stored until it is cleared using the GTS. | ||
| The radio receiver assembly does not receive data from the ECM for 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for 10 seconds or more.
·
The power source voltage of the radio receiver assembly is 9.5 V.
·
The vehicle speed is 20 km/h (12 mph) or more. |
Drive the vehicle for 20 seconds or more at a speed of 20 km/h (12 mph) or more. | - | - | DTC is stored until it is cleared using the GTS. | ||
| U0129 | VSC(ECB)ECU Communication | The radio receiver assembly does not receive data from the brake actuator assembly (No. 2 skid control ECU) for 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for 10 seconds or more.
·
The power source voltage of the radio receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| All conditions are met:
·
The ignition switch is ON for 10 seconds or more.
·
The power source voltage of the radio receiver assembly is 9.5 V.
·
The vehicle speed is 20 km/h (12 mph) or more. |
Drive the vehicle for 20 seconds or more at a speed of 20 km/h (12 mph) or more. | - | - | DTC is stored until it is cleared using the GTS. | |||
| The radio receiver assembly does not receive data from the brake actuator assembly (No. 2 skid control ECU) for 4 seconds or more. | All conditions are met:
·
The ignition switch is ON for 10 seconds or more.
·
The power source voltage of the radio receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. | ||
| U0132 | Air Suspension ECU Communication | The radio receiver assembly does not receive data from the absorber control ECU for 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for 10 seconds or more.
·
The power source voltage of the radio receiver assembly is 9.5 V.
·
The vehicle speed is 20 km/h (12 mph) or more. |
Drive the vehicle for 20 seconds or more at a speed of 20 km/h (12 mph) or more. | - | - | DTC is stored until it is cleared using the GTS. |
| U0140 | Lost Communication with Body Control Module | The radio receiver assembly does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for 10 seconds or more.
·
The power source voltage of the radio receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Meter ECU Communication | The radio receiver assembly does not receive data from the main body ECU (multiplex network body ECU) for 30 seconds or more. | All conditions are met:
·
The ignition switch is ON for 30 seconds or more.
·
The power source voltage of the radio receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least 60 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0164 | Air Conditioner ECU Communication | The radio receiver assembly does not receive data from the air conditioning amplifier assembly for 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for 10 seconds or more.
·
The power source voltage of the radio receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least 20 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0198 | Lost Communication with Telematic Control Module | The radio receiver assembly does not receive data from the telephone transceiver assembly for 3 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the radio receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least 6 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0208 | Lost Communication with "Seat Control Module A" | The radio receiver assembly does not receive data from the position control ECU assembly for 15 seconds or more. | All conditions are met:
·
The ignition switch is ON for 15 seconds or more.
·
The power source voltage of the radio receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least 30 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0209 | Lost Communication with "Seat Control Module B" | The radio receiver assembly does not receive data from the position control ECU assembly for 15 seconds or more. | All conditions are met:
·
The ignition switch is ON for 15 seconds or more.
·
The power source voltage of the radio receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least 30 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U023B | Lost Communication with Image Processing Module "B" | The radio receiver assembly does not receive data from the parking assist ECU for approximately 12 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 12 seconds or more.
·
The power source voltage of the radio receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least approximately 24 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U0265 | Lost Communication with Image Processing Sensor A | The radio receiver assembly does not receive data from the rear television camera assembly for approximately 12 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 12 seconds or more.
·
The power source voltage of the radio receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least approximately 24 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U1110 | Clearance Sonar ECU Communication | The radio receiver assembly does not receive data from the clearance warning ECU assembly for 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for 10 seconds or more.
·
The power source voltage of the radio receiver assembly is 9.5 V. |
Turn the ignition switch to ON and wait for at least 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
Combination Meter Assembly / GTS Display "Combination Meter"
DTC communication uses the CAN communication system.
*1: w/ Audio and Visual System (for Radio and Display Type, for 12.3 Inch Display)
*2: w/ Audio and Visual System (for Radio and Display Type, except 12.3 Inch Display)
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U010087 | Lost Communication with ECM/PCM "A" Missing Message | The combination meter assembly does not receive data from the ECM for approximately 4 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the combination meter assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least approximately 7 seconds. | MIL (malfunction indicator lamp) illuminates | - | DTC is stored until it is cleared using the GTS. |
| U012687 | Lost Communication with Steering Angle Sensor Module Missing Message | The combination meter assembly does not receive data from the steering sensor for 4 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the combination meter assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least approximately 7 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U012787 | Lost Communication with Tire Pressure Monitor Module Missing Message | The combination meter assembly does not receive data from the tire pressure warning ECU and receiver for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the combination meter assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| The combination meter assembly does not receive data from the tire pressure warning ECU and receiver for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the combination meter assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. | ||
| U012987 | Lost Communication with Brake System Control Module Missing Message | The combination meter assembly does not receive data from the brake actuator assembly (No. 2 skid control ECU) for approximately 4 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the combination meter assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least approximately 7 seconds. |
·
ABS warning light illuminates
·
brake actuator assembly (No. 2 skid control ECU) warning light illuminates
·
BRAKE warning light illuminates |
- | DTC is stored until it is cleared using the GTS. |
| The combination meter assembly does not receive data from the brake actuator assembly (No. 2 skid control ECU) for 1 second or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the combination meter assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 4 seconds. |
·
ABS warning light illuminates
·
brake actuator assembly (No. 2 skid control ECU) warning light illuminates
·
BRAKE warning light illuminates |
- | DTC is stored until it is cleared using the GTS. | ||
| U013187 | Lost Communication with Power Steering Control Module Missing Message | The combination meter assembly does not receive data from the power steering ECU assembly for approximately 4 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the combination meter assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least approximately 7 seconds. | PPS warning light illuminates | - | DTC is stored until it is cleared using the GTS. |
| U013287 | Lost Communication with Suspension Control Module "A" Missing Message | The combination meter assembly does not receive data from the absorber control ECU for 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the combination meter assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 13 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U014087 | Lost Communication with Body Control Module Missing Message | The combination meter assembly does not receive data from the main body ECU (multiplex network body ECU) for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the combination meter assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U015187 | Lost Communication with Restraints Control Module Missing Message | The combination meter assembly does not receive data from the airbag ECU assembly for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the combination meter assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 8 seconds. | A/B warning light illuminates | - | DTC is stored until it is cleared using the GTS. |
| U016387 | Lost Communication with Navigation Control Module Missing Message | Either of the following conditions is met:
·
The combination meter assembly does not receive data from the radio receiver assembly for 5 seconds or more.*1
·
The combination meter assembly does not receive data from the radio and display receiver assembly for 5 seconds or more.*2 |
All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the combination meter assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U016487 | Lost Communication with HVAC Control Module Missing Message | The combination meter assembly does not receive data from the air conditioning amplifier assembly for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the combination meter assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U016887 | Lost Communication with Vehicle Security Control Module Missing Message | The combination meter assembly does not receive data from the certification ECU (smart key ECU assembly) for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the combination meter assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U018287 | Lost Communication with Lighting Control Module Front Missing Message | The combination meter assembly does not receive data from the headlight ECU sub-assembly LH for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the combination meter assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U023087 | Lost Communication with Rear Gate Module Missing Message | The combination meter assembly does not receive data from the multiplex network door ECU for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the combination meter assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U023387 | Lost Communication with Side Obstacle Detection Control Module "B" Missing Message | The combination meter assembly does not receive data from the blind spot monitor sensor LH for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the combination meter assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U023A87 | Lost Communication with Image Processing Module "A" Missing Message | The combination meter assembly does not receive data from the forward recognition camera for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the combination meter assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 8 seconds. | LDA indicator illuminates | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U032787 | Software Incompatibility with Vehicle Security Control Module Missing Message | The combination meter assembly does not receive data from the certification ECU (smart key ECU assembly) for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the combination meter assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U110387 | Lost Communication with Stop and Start Control Module Missing Message | The combination meter assembly does not receive data from the engine stop and start ECU for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the combination meter assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U110487 | Lost Communication with Driving Support ECU Missing Message | The combination meter assembly does not receive data from the forward recognition camera for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the combination meter assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 8 seconds. |
·
PCS warning light illuminates
·
LDA indicator light illuminates |
Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U110687 | Lost Communication with Electric Parking Brake Module Missing Message | The combination meter assembly does not receive data from the brake actuator assembly (No.2 skid control ECU) for approximately 4 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the combination meter assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least approximately 7 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U111087 | Lost Communication with Clearance Sonar Module Missing Message | The combination meter assembly does not receive data from the clearance warning ECU assembly for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the combination meter assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 8 seconds. | Clearance sonar-off indicator light illuminates | - | DTC is stored until it is cleared using the GTS. |
| U111287 | Lost Communication with Combination Switch Module Missing Message | The combination meter assembly does not receive data from the steering sensor for 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the combination meter assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 13 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
Meter Mirror Sub-assembly / GTS Display "Head Up Display" (w/ Headup Display System)
DTC communication uses the CAN communication system.
*1: w/ Audio and Visual System (for Radio and Display Type, for 12.3 Inch Display)
*2: w/ Audio and Visual System (for Radio and Display Type, except 12.3 Inch Display)
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U010087 | Lost Communication with ECM/PCM "A" Missing Message | The meter mirror sub-assembly does not receive data from the ECM for approximately 4 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the meter mirror sub-assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least approximately 7 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U012987 | Lost Communication with Brake System Control Module Missing Message | The meter mirror sub-assembly does not receive data from the brake actuator assembly (No. 2 skid control ECU) for approximately 4 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the meter mirror sub-assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least approximately 7 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U014287 | Lost Communication with Body Control Module "B" Missing Message | The meter mirror sub-assembly does not receive data from the main body ECU (multiplex network body ECU) for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the meter mirror sub-assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U015587 | Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message | The meter mirror sub-assembly does not receive data from the combination meter assembly for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the meter mirror sub-assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U016387 | Lost Communication with Navigation Control Module Missing Message | Either of the following conditions is met:
·
The meter mirror sub-assembly does not receive data from the radio receiver assembly for 5 seconds or more.*1
·
The meter mirror sub-assembly does not receive data from the radio and display receiver assembly for 5 seconds or more.*2 |
All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the meter mirror sub-assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U016487 | Lost Communication with HVAC Control Module Missing Message | The meter mirror sub-assembly does not receive data from the air conditioning amplifier assembly for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the meter mirror sub-assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U023587 | Lost Communication with Cruise Control Front Distance Range Sensor Missing Message | The meter mirror sub-assembly does not receive data from the forward recognition camera for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the meter mirror sub-assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U023A87 | Lost Communication with Image Processing Module "A" Missing Message | The meter mirror sub-assembly does not receive data from the forward recognition camera for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the meter mirror sub-assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U110387 | Lost Communication with Stop and Start Control Module Missing Message | The meter mirror sub-assembly does not receive data from the engine stop and start ECU for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the meter mirror sub-assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U110487 | Lost Communication with Driving Support ECU Missing Message | Either of the following conditions is met:
·
The meter mirror sub-assembly does not receive data from the forward recognition camera for approximately 4 seconds or more.
·
The meter mirror sub-assembly does not receive data from the forward recognition camera for 5 seconds or more. |
All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the meter mirror sub-assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U111087 | Lost Communication with Clearance Sonar Module Missing Message | The meter mirror sub-assembly does not receive data from the clearance warning ECU assembly for approximately 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the meter mirror sub-assembly is 10.5 V or higher. |
Turn the ignition switch to ON and wait at least 8 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
Telephone Transceiver Assembly / GTS Display "Telematics" (w/ Telematics System)
DTC communication uses the CAN communication system.
*1: w/ Audio and Visual System (for Radio and Display Type, for 12.3 Inch Display)
*2: w/ Audio and Visual System (for Radio and Display Type, except 12.3 Inch Display)
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U015587 | Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message | Communication stops between the telephone transceiver assembly and the combination meter assembly for aproximately 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the telephone transceiver assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U014087 | Lost Communication with Body Control Module Missing Message | Communication stops between the telephone transceiver assembly and the main body ECU (multiplex network body ECU) for aproximately 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the telephone transceiver assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U016387 | Lost Communication with Navigation Control Module Missing Message | Either of the following conditions is met:
·
Communication stops between the telephone transceiver assembly and the radio receiver assembly for aproximately 10 seconds or more.*1
·
Communication stops between the telephone transceiver assembly and the radio and display receiver assembly for aproximately 10 seconds or more.*2 |
All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the telephone transceiver assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
Airbag ECU Assembly / GTS Display "SRS Airbag"
DTC communication uses the CAN communication system.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U012987 | Lost Communication with Brake System Control Module "A" Missing Message | Communication stops between the airbag ECU assembly and the brake actuator assembly (No. 2 skid control ECU) for approximately 2 seconds or more. | The ignition switch is ON for approximately 3 seconds or more. | Turn the ignition switch to ON and wait for at least approximately 5 seconds. |
·
The SRS warning light illuminates.
·
Pedestrian protection system warning light illuminates. |
- | DTC is stored until it is cleared using the GTS. |
| U023587 | Lost Communication with Cruise Control Front Distance Range Sensor Single Sensor or Center Missing Message | Communication stops between the airbag ECU assembly and the millimeter wave radar sensor assembly for approximately 10 seconds or more. | The ignition switch is ON for approximately 3 seconds or more. | Turn the ignition switch to ON and wait for at least approximately 13 seconds. |
·
The SRS warning light illuminates.
·
Pedestrian protection system warning light illuminates. |
- | DTC is stored until it is cleared using the GTS. |
| U023A87 | Lost Communication with Image Processing Module "A" Missing Message | Communication stops between the airbag ECU assembly and the forward recognition camera for approximately 10 seconds or more. | The ignition switch is ON for approximately 3 seconds or more. | Turn the ignition switch to ON and wait for at least approximately 13 seconds. |
·
The SRS warning light illuminates.
·
Pedestrian protection system warning light illuminates. |
- | DTC is stored until it is cleared using the GTS. |
| U110487 | Lost Communication with Driving Support ECU Missing Message | Communication stops between the airbag ECU assembly and the forward recognition camera for approximately 10 seconds or more. | The ignition switch is ON for approximately 3 seconds or more. | Turn the ignition switch to ON and wait for at least approximately 13 seconds. |
·
The SRS warning light illuminates.
·
Pedestrian protection system warning light illuminates. |
- | DTC is stored until it is cleared using the GTS. |
Brake Actuator Assembly (No. 2 Skid Control ECU) / GTS Display "Brake/EPB*"
DTC communication uses the CAN communication system.
EPB*: Electric Parking Brake
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U010087 | Lost Communication with ECM/PCM "A" Missing Message | Communication stops between the brake actuator assembly (No. 2 skid control ECU) and the ECM for aproximately 2 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 5 seconds. |
·
ABS warning light illuminates
·
SLIP indicator light illuminates
·
BH indicator light illuminates
·
EPB warning light illuminates
·
MIL (malfunction indicator lamp) illuminates |
Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U010187 | Lost Communication with TCM Missing Message |
·
Communication stops between the brake actuator assembly (No. 2 skid control ECU) and the TCM for aproximately 2 seconds or more. (for V35F-FTS)
·
Communication stops between the brake actuator assembly (No. 2 skid control ECU) and the ECM for aproximately 2 seconds or more. (for 1GR-FE) |
All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.5 V or more. |
Turn the ignition switch to ON (IG) and wait for at least approximately 5 seconds. |
·
ABS warning light illuminates
·
SLIP indicator light illuminates
·
BH indicator light illuminates
·
EPB warning light illuminates |
Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U011487 | Lost Communication with Four-Wheel Drive Clutch Control Module Missing Message | Communication stops between the brake actuator assembly (No. 2 skid control ECU) and the 4 wheel drive control ECU for aproximately 2 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 5 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U012587 | Lost Communication with Multi-axis Acceleration Sensor Module Missing Message | Communication stops between the brake actuator assembly (No. 2 skid control ECU) and the airbag ECU assembly for aproximately 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 8 seconds. |
·
ABS warning light illuminates
·
SLIP indicator light illuminates
·
BH indicator light illuminates
·
EPB warning light illuminates
·
ECB warning light illuminates |
Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U012687 | Lost Communication with Steering Angle Sensor Module Missing Message | Communication stops between the brake actuator assembly (No. 2 skid control ECU) and the steering sensor for aproximately 1 second or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 4 seconds. |
·
SLIP indicator light illuminates
·
BH indicator light blinks |
- | DTC is stored until it is cleared using the GTS. |
| U013287 | Lost Communication with Suspension Control Module "A" Missing Message | Communication stops between the brake actuator assembly (No. 2 skid control ECU) and the absorber control ECU for aproximately 1 second or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 4 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U014087 | Lost Communication with Body Control Module Missing Message | Communication stops between the brake actuator assembly (No. 2 skid control ECU) and the main body ECU (multiplex network body ECU) for aproximately 2 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 5 seconds. | MIL (malfunction indicator lamp) illuminates | - | DTC is stored until it is cleared using the GTS. |
| U015187 | Lost Communication with Restraints Control Module Missing Message | Communication stops between the brake actuator assembly (No. 2 skid control ECU) and the airbag ECU assembly for aproximately 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 8 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U025E87 | Lost Communication with Electronic Brake Booster Control Module "A" Missing Message | Communication stops between the brake actuator assembly (No. 2 skid control ECU) and the brake booster with master cylinder assembly (No. 1 skid control ECU) for aproximately 2 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 5 seconds. |
·
ECB warning light illuminates
·
Brake warning light blinks |
- | DTC is stored until it is cleared using the GTS. |
| U110687 | Lost Communication with Electric Parking Brake Module Missing Message | Communication stops between the brake actuator assembly (No. 2 skid control ECU) and the brake actuator assembly (No.2 skid control ECU) for aproximately 1 second or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 4 seconds. |
·
EPB warning light illuminates
·
BH indicator light blinks |
- | DTC is stored until it is cleared using the GTS. |
| U110787 | Lost Communication with Power Management Module Missing Message | Communication stops between the brake actuator assembly (No. 2 skid control ECU) and the certification ECU (smart key ECU assembly) for aproximately 3 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 6 seconds. | ECB warning light illuminates | - | DTC is stored until it is cleared using the GTS. |
| U115987 | Lost Communication With Electronic Brake Booster Control Module "A" (ch3) Missing Message | Communication stops between the brake actuator assembly (No. 2 skid control ECU) and the brake booster with master cylinder assembly (No. 1 skid control ECU) for aproximately 2 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 5 seconds. | ECB warning light illuminates | - | DTC is stored until it is cleared using the GTS. |
| U115C87 | Lost Communication with ECM/PCM "A" (ch5) Missing Message | Communication stops between the brake actuator assembly (No. 2 skid control ECU) and the ECM for aproximately 2 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 5 seconds. |
·
SLIP indicator light illuminates
·
BH indicator light blinks
·
ABS warning light illuminates |
Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
Brake Booster with Master Cylinder Assembly (No. 1 Skid Control ECU) / GTS Display "Brake Booster"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U010000 | Lost Communication with ECM/PCM "A" | Communication stops between the brake booster with master cylinder assembly (No. 1 skid control ECU) and the ECM for aproximately 2 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the brake booster with master cylinder assembly (No. 1 skid control ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 5 seconds. | ECB warning light illuminates | - | DTC is stored until it is cleared using the GTS. |
| U010100 | Lost Communication with TCM | Communication stops between the brake booster with master cylinder assembly (No. 1 skid control ECU) and the TCM for aproximately 2 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the brake booster with master cylinder assembly (No. 1 skid control ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 5 seconds. | ECB warning light illuminates | - | DTC is stored until it is cleared using the GTS. |
| U012987 | Lost Communication with Brake System Control Module "A" Missing Message | Communication stops between the brake booster with master cylinder assembly (No. 1 skid control ECU) and the brake actuator assembly (No. 2 skid control ECU) for aproximately 2 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 5 seconds. | ECB warning light illuminates | - | DTC is stored until it is cleared using the GTS. |
| U110600 | Lost Communication with Electric Parking Brake Module | Communication stops between the brake booster with master cylinder assembly (No. 1 skid control ECU) and the brake actuator assembly (No.2 skid control ECU) for aproximately 1 second or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the brake booster with master cylinder assembly (No. 1 skid control ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 4 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U115C00 | Lost Communication with ECM/PCM "A" (ch5) | Communication stops between the brake booster with master cylinder assembly (No. 1 skid control ECU) and the ECM for aproximately 2 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the brake booster with master cylinder assembly (No. 1 skid control ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 5 seconds. | ECB warning light illuminates | - | DTC is stored until it is cleared using the GTS. |
| U117D87 | Lost Communication with Brake System Control Module (ch4) Missing Message | Communication stops between the brake booster with master cylinder assembly (No. 1 skid control ECU) and the brake actuator assembly (No. 2 skid control ECU) for aproximately 2 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 5 seconds. | ECB warning light illuminates | - | DTC is stored until it is cleared using the GTS. |
Tire Pressure Warning ECU andReceiver / GTS Display "Tire Pressure Monitor" (w/ Tire Pressure Warning System)
DTC communication uses the CAN communication system.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U012987 | Lost Communication with Brake System Control Module "A" Missing Message | The tire pressure warning ECU and receiverS does not receive data from the brake actuator assembly (No. 2 skid control ECU) for 60 seconds or more. | The ignition switch is ON for 1 second or more. | Turn the ignition switch to ON and wait at least approximately 61 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
4 Wheel Drive Control ECU / GTS Display "Four Wheel Drive"
DTC communication uses the CAN communication system.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U012987 | Lost Communication with Brake System Control Module "A" Missing Message | Communication stops between the 4 wheel drive control ECU and the brake actuator assembly (No. 2 skid control ECU) for aproximately 4 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the 4 wheel drive control ECU is 10 V or more. |
Turn the ignition switch to ON and wait for at least approximately 7 seconds. | 4WD warning light illuminates | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
Forward Recognition Camera / GTS Display "Cruise Control" (w/ Pre-collision System)
DTC communication uses the CAN communication system.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U010087 | Lost Communication with ECM/PCM "A" Missing Message | The forward recognition camera does not receive data from the ECM for approximately 1 second or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The dynamic radar cruise control system is in operation.
·
The power source voltage of the forward recognition camera is 10 V or more. |
With the dynamic radar cruise operating, drive the vehicle for approximately 4 seconds or more. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U012687 | Lost Communication with Steering Angle Sensor Module Missing Message | The forward recognition camera does not receive data from the steering sensor for approximately 1 second or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The dynamic radar cruise control system is in operation.
·
The power source voltage of the forward recognition camera is 10 V or more. |
With the dynamic radar cruise operating, drive the vehicle for approximately 4 seconds or more. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U012987 | Lost Communication with Brake System Control Module Missing Message | The forward recognition camera does not receive data from the brake actuator assembly (No. 2 skid control ECU) for approximately 2 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The dynamic radar cruise control system is in operation.
·
The power source voltage of the forward recognition camera is 10 V or more. |
With the dynamic radar cruise operating, drive the vehicle for approximately 4 seconds or more. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U015587 | Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message | The forward recognition camera does not receive data from the combination meter assembly for approximately 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The dynamic radar cruise control system is in operation.
·
The power source voltage of the forward recognition camera is 10 V or more. |
With the dynamic radar cruise operating, drive the vehicle for approximately 8 seconds or more. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U030057 | Internal Control Module Software Incompatibility Invalid / Incompatible Software Component | The vehicle information sent from the ECM does not match that stored in the forward recognition camera for 1 second or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The dynamic radar cruise control system is in operation.
·
The power source voltage of the forward recognition camera is 10 V or more. |
With the dynamic radar cruise operating, drive the vehicle for approximately 4 seconds or more. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U032251 | Software Incompatibility with Body Control Module Not Programmed | The vehicle information sent from main body ECU (multiplex network body ECU) remains undefined by the forward recognition camera for 6 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The dynamic radar cruise control system is in operation.
·
The power source voltage of the forward recognition camera is 10 V or more. |
With the dynamic radar cruise operating, drive the vehicle for approximately 9 seconds or more. | - | Displays messages on the multi-information display. | DTC remains stored only while malfunction is occurring. |
| U032257 | Software Incompatibility with Body Control Module Invalid / Incompatible Software Component | The vehicle information sent from the main body ECU (multiplex network body ECU) does not match that stored in the forward recognition camera for 4 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The dynamic radar cruise control system is in operation.
·
The power source voltage of the forward recognition camera is 10 V or more. |
With the dynamic radar cruise operating, drive the vehicle for approximately 7 seconds or more. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
Forward Recognition Camera / GTS Display "Lane Control" (w/ Pre-collision System)
DTC communication uses the CAN communication system.
*1: for 1GR-FE
*2: except 1GR-FE
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U010087 | Lost Communication with ECM/PCM "A" Missing Message | Communication stops between the forward recognition camera and the ECM for approximately 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
Vehicle speed is 5 km/h (3 mph) or more.
·
The LTA switch is on.
·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the LTA switch on and drive the vehicle for 8 seconds or more at a speed of 5 km/h (3 mph) or more. | LTA indicator light (yellow) illuminates. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U010187 | Lost Communication with TCM Missing Message | Either of the following conditions is met:
·
Communication stops between the forward recognition camera and the ECM for approximately 5 seconds or more.*1
·
Communication stops between the forward recognition camera and the TCM for approximately 5 seconds or more.*2 |
All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
Vehicle speed is 5 km/h (3 mph) or more.
·
The LTA switch is on.
·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the LTA switch on and drive the vehicle for 8 seconds or more at a speed of 5 km/h (3 mph) or more. | LTA indicator light (yellow) illuminates. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U012587 | Lost Communication with Multi-axis Acceleration Sensor Module Missing Message | Communication stops between the forward recognition camera and the airbag ECU assembly for approximately 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
Vehicle speed is 5 km/h (3 mph) or more.
·
The LTA switch is on.
·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the LTA switch on and drive the vehicle for 8 seconds or more at a speed of 5 km/h (3 mph) or more. | LTA indicator light (yellow) illuminates. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U012687 | Lost Communication with Steering Angle Sensor Module Missing Message | Communication stops between the forward recognition camera and the steering sensor for approximately 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
Vehicle speed is 5 km/h (3 mph) or more.
·
The LTA switch is on.
·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the LTA switch on and drive the vehicle for 8 seconds or more at a speed of 5 km/h (3 mph) or more. | LTA indicator light (yellow) illuminates. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U012987 | Lost Communication with Brake System Control Module Missing Message | Communication stops between the forward recognition camera and the brake actuator assembly (No. 2 skid control ECU) for approximately 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
Vehicle speed is 5 km/h (3 mph) or more.
·
The LTA switch is on.
·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the LTA switch on and drive the vehicle for 8 seconds or more at a speed of 5 km/h (3 mph) or more. | LTA indicator light (yellow) illuminates. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U013187 | Lost Communication with Power Steering Control Module Missing Message | Communication stops between the forward recognition camera and the power steering ECU assembly for approximately 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The LTA switch is on.
·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the LTA switch on and wait for at least 8 seconds. | LTA indicator light (yellow) illuminates. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U015587 | Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message | Communication stops between the forward recognition camera and the combination meter assembly for approximately 50 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
Vehicle speed is 5 km/h (3 mph) or more.
·
The LTA switch is on.
·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the LTA switch on and drive the vehicle for 53 seconds or more at a speed of 5 km/h (3 mph) or more. | LTA indicator light (yellow) illuminates. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U023587* | Lost Communication with Cruise Control Front Distance Range Sensor Single Sensor or Center Missing Message | Communication stops between the forward recognition camera and the millimeter wave radar sensor assembly for approximately 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The LTA switch is on.
·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the LTA switch on and wait for at least 8 seconds. | LTA indicator light (yellow) illuminates. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U030051* | Internal Control Module Software Incompatibility Not Programmed | The vehicle information sent from the ECM remains undefined by the forward recognition camera for approximately 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The LTA switch is on.
·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the LTA switch on and wait for at least 8 seconds. | LTA indicator light (yellow) illuminates. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U030057* | Internal Control Module Software Incompatibility Invalid / Incompatible Software Component | The vehicle information sent from the ECM does not match that stored in the forward recognition camera for approximately 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The LTA switch is on.
·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the LTA switch on and wait for at least 8 seconds. | LTA indicator light (yellow) illuminates. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
Forward Recognition Camera / GTS Display "Road Sign Assist" (w/ Road Sign Assist System)
DTC communication uses the CAN communication system.
*1: for 1GR-FE
*2: except 1GR-FE
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U012987 | Lost Communication with Brake System Control Module Missing Message | Communication stop occurs between the forward recognition camera and brake actuator assembly (No. 2 skid control ECU) continuously for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON.
·
The power source voltage of the forward recognition camera is 9.5 V or more. |
Turn the ignition switch to ON and wait at least approximately 5 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U010087 | Lost Communication with ECM/PCM "A" Missing Message | Communication stop occurs between the forward recognition camera and ECM continuously for 5 seconds or more. | All conditions are met:
·
Vehicle speed is 1 km/h or 1 mph or more.
·
The power source voltage of the forward recognition camera is 9.5 V or more. |
Turn the ignition switch to ON and wait at least approximately 5 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U010187 | Lost Communication with TCM Missing Message | Either of the following conditions is met:
·
Communication stop occurs between the forward recognition camera and ECM continuously for 5 seconds or more.*1
·
Communication stop occurs between the forward recognition camera and TCM continuously for 5 seconds or more.*2 |
All conditions are met:
·
Vehicle speed is 1 km/h or 1 mph or more.
·
The power source voltage of the forward recognition camera is 9.5 V or more. |
Turn the ignition switch to ON and wait at least approximately 5 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U015587 | Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message | Communication stop occurs between the forward recognition camera and combination meter assembly continuously for 50 seconds or more. | All conditions are met:
·
The ignition switch is ON.
·
The power source voltage of the forward recognition camera is 9.5 V or more. |
Turn the ignition switch to ON and wait at least approximately 5 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U014087 | Lost Communication with Body Control Module Missing Message | Communication stop occurs between the forward recognition camera and main body ECU (multiplex network body ECU) continuously for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON.
·
The power source voltage of the forward recognition camera is 9.5 V or more. |
Turn the ignition switch to ON and wait at least approximately 5 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U012687 | Lost Communication with Steering Angle Sensor Module Missing Message | Communication stop occurs between the forward recognition camera and steering sensor continuously for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON.
·
The power source voltage of the forward recognition camera is 9.5 V or more. |
Turn the ignition switch to ON and wait at least approximately 5 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
Forward Recognition Camera / GTS Display "Pre-collision System" (w/ Pre-collision System)
DTC communication uses the CAN communication system.
*1: for 1GR-FE
*2: except 1GR-FE
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U010087 | Lost Communication with ECM/PCM "A" Missing Message | The forward recognition camera does not receive data from the ECM for approximately 2 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the ignition switch to ON and wait for at least approximately 5 seconds. | PCS indicator light illuminates | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U012687 | Lost Communication with Steering Angle Sensor Module Missing Message | The forward recognition camera does not receive data from the steering sensor for approximately 2 second or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the ignition switch to ON and wait for at least approximately 5 seconds. | PCS indicator light illuminates | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U012987 | Lost Communication with Brake System Control Module Missing Message | The forward recognition camera does not receive data from the brake actuator assembly (No. 2 skid control ECU) for approximately 2 second or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the ignition switch to ON and wait for at least approximately 5 seconds. | PCS indicator light illuminates | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U010187 | Lost Communication with TCM Missing Message | Either of the following conditions is met:
·
The forward recognition camera does not receive data from the ECM for approximately 9 seconds or more.*1
·
The forward recognition camera does not receive data from the TCM for approximately 9 seconds or more.*2 |
All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the ignition switch to ON and wait for at least approximately 12 seconds. | PCS indicator light illuminates | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U023587 | Lost Communication with Cruise Control Front Distance Range Sensor Single Sensor or Center Missing Message | The forward recognition camera does not receive data from the millimeter wave radar sensor for approximately 2 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the ignition switch to ON and wait for at least approximately 5 seconds. | PCS indicator light illuminates | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U118F87 | Lost Communication with Steering Actuator Control Module Missing Message | The forward recognition camera does not receive data from the power steering ECU with motor assembly for approximately 2 second or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the ignition switch to ON and wait for at least approximately 5 seconds. | PCS indicator light illuminates | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U041881 | Invalid Data Received from Brake System Control Module Invalid Serial Data Received | The forward recognition camera receives an abnormal brake system control signal from the brake actuator assembly (No. 2 skid control ECU) for approximately 1 second or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the ignition switch to ON and wait for at least approximately 4 seconds. | PCS indicator light illuminates | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U030051 | Internal Control Module Software Incompatibility Not Programmed | The vehicle information sent from ECM remains undefined by the forward recognition camera for approximately 4 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the ignition switch to ON and wait for at least approximately 7 seconds. | PCS indicator light illuminates | Displays messages on the multi-information display. | DTC remains stored only while malfunction is occurring. |
| U030057 | Internal Control Module Software Incompatibility Invalid / Incompatible Software Component | The vehicle information sent from the ECM does not match that stored in the forward recognition camera for approximately 2 second or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the ignition switch to ON and wait for at least approximately 5 seconds. | PCS indicator light illuminates | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U032857 | Software Incompatibility with Steering Angle Sensor Module Invalid / Incompatible Software Component | The VGRS ECU existing information from the steering sensor does not match that stored in the forward recognition camera for approximately 4 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more.
·
The power source voltage of the forward recognition camera is 10 V or more. |
Turn the ignition switch to ON and wait for at least approximately 7 seconds. | PCS indicator light illuminates | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
Blind Spot Monitor Sensor LH / GTS Display "Blind Spot Monitor "B"" (w/ Blind Spot Monitor System)
DTC communication uses the CAN communication system.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U010087 | Lost Communication with ECM/PCM "A" Missing Message | Communication stops between the blind spot monitor sensor LH and the ECM for aproximately 11 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the blind spot monitor sensor LH is 10.5 V or more.
·
Vehicle speed is 5 km/h (3 mph) or more. |
Drive the vehicle at a speed of 5 km/h (3 mph) or more for approximately 14 seconds or more. |
·
BSM indicator light illuminates (umber)
·
RCTA indicator light illuminates (umber) |
Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U012687 | Lost Communication with Steering Angle Sensor Module Missing Message | Communication stops between the blind spot monitor sensor LH and the steering sensor for aproximately 4 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the blind spot monitor sensor LH is 10.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 7 seconds. |
·
BSM indicator light illuminates (umber)
·
RCTA indicator light illuminates (umber) |
Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| Communication stops between the blind spot monitor sensor LH and the steering sensor for aproximately 11 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the blind spot monitor sensor LH is 10.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 14 seconds. |
·
BSM indicator light illuminates (umber)
·
RCTA indicator light illuminates (umber) |
Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. | ||
| U012987 | Lost Communication with Brake System Control Module "A" Missing Message | Communication stops between the blind spot monitor sensor LH and the brake actuator assembly (No. 2 skid control ECU) for aproximately 4 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the blind spot monitor sensor LH is 10.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 7 seconds. |
·
BSM indicator light illuminates (umber)
·
RCTA indicator light illuminates (umber) |
Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U014087 | Lost Communication with Body Control Module Missing Message | Communication stops between the blind spot monitor sensor LH and the main body ECU (multiplex network body ECU) for aproximately 11 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the blind spot monitor sensor LH is 10.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 14 seconds. |
·
BSM indicator light illuminates (umber)
·
RCTA indicator light illuminates (umber) |
Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U111087 | Lost Communication with Clearance Sonar Module Missing Message | Communication stops between the blind spot monitor sensor LH and the clearance warning ECU assembly for aproximately 11 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the blind spot monitor sensor LH is 10.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 14 seconds. | RCTA indicator light illuminates (umber) | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U023287 | Lost Communication with Side Obstacle Detection Control Module "A" Missing Message | Communication stops between the blind spot monitor sensor LH (master) and blind spot monitor sensor RH (slave) occurs for approximately 11 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the blind spot monitor sensor LH is 10.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 14 seconds. |
·
BSM indicator light illuminates (umber)
·
RCTA indicator light illuminates (umber) |
Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U032251 | Software Incompatibility with Body Control Module Not Programmed | The destination information of main body ECU (multiplex network body ECU) does not match that of blind spot monitor sensor LH. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the blind spot monitor sensor LH is 9 V or more. |
Turn the ignition switch to ON and wait for at least approximately 7 seconds. |
·
BSM indicator light illuminates (umber)
·
RCTA indicator light illuminates (umber) |
Displays messages on the multi-information display. | DTC remains stored only while malfunction is occurring. |
| U032257 | Software Incompatibility with Body Control Module Invalid / Incompatible Software Component | The destination information of main body ECU (multiplex network body ECU) does not match that of blind spot monitor sensor LH. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the blind spot monitor sensor LH is 10.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 3 seconds. |
·
BSM indicator light illuminates (umber)
·
RCTA indicator light illuminates (umber) |
Displays messages on the multi-information display. | DTC remains stored only while malfunction is occurring. |
Parking Assist ECU / GTS Display "Circumference Monitoring Camera Module" (w/ Multi-terrain Monitor System)
DTC communication uses the CAN communication system.
*1: for 1GR-FE
*2: except 1GR-FE
*3: w/ Audio and Visual System (for Radio and Display Type, for 12.3 Inch Display)
*4: w/ Audio and Visual System (for Radio and Display Type, except 12.3 Inch Display)
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U100087 | Lost Communication with ECM/PCM "A" Missing Message | When the ignition switch is ON, a CAN communication malfunction is detected. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the parking assist ECU is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 3 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U010087 | Lost Communication with ECM/PCM "A" Missing Message | Either of the following conditions is met:
·
Communication stops between the parking assist ECU and the ECM for aproximately 2 seconds or more.*1
·
Communication stops between the parking assist ECU and the TCM for aproximately 2 seconds or more.*2 |
All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the parking assist ECU is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 5 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U012987 | Lost Communication with Brake System Control Module "A" Missing Message | Communication stops between the parking assist ECU and the brake actuator assembly (No. 2 skid control ECU) for aproximately 2 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the parking assist ECU is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 5 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U013187 | Lost Communication with Power Steering Control Module Missing Message | Communication stops between the parking assist ECU and the power steering ECU assembly for aproximately 2 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the parking assist ECU is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 5 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U014087 | Lost Communication with Body Control Module Missing Message | Communication stops between the parking assist ECU and the main body ECU (multiplex network body ECU) for aproximately 4 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the parking assist ECU is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 7 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U012687 | Lost Communication with Steering Angle Sensor Module Missing Message | Communication stops between the parking assist ECU and the steering sensor for aproximately 2 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the parking assist ECU is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 5 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U111087 | Lost Communication with Clearance Sonar Module Missing Message | Communication stops between the parking assist ECU and the clearance warning ECU assembly for aproximately 11 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the parking assist ECU is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 14 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U016387 | Lost Communication with Navigation Control Module Missing Message | Either of the following conditions is met:
·
Communication stops between the parking assist ECU and the radio receiver assembly for aproximately 11 seconds or more.*3
·
Communication stops between the parking assist ECU and the radio and display receiver assembly for aproximately 11 seconds or more.*4 |
All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the parking assist ECU is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 14 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U023387 | Lost Communication with Side Obstacle Detection Control Module "B" Missing Message | Communication stops between the parking assist ECU and the blind spot monitor sensor LH for aproximately 11 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the parking assist ECU is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 14 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U026587 | Lost Communication with Image Processing Sensor A Missing Message | Communication stops between the parking assist ECU and the rear television camera assembly for aproximately 2 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the parking assist ECU is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 5 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U110487 | Lost Communication with Driving Support ECU Missing Message | Communication stops between the parking assist ECU and the forward recognition camera for aproximately 11 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the parking assist ECU is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 14 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
Clearance Warning ECU Assembly / GTS Display "Circumference Monitoring Camera Module" (w/ TOYOTA Parking Assist sensor System)
DTC communication uses the CAN communication system.
*1: for 1GR-FE
*2: except 1GR-FE
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U010087 | Lost Communication with ECM/PCM "A" Missing Message | Communication stops between the clearance warning ECU assembly and the ECM for aproximately 1 second or more. | All conditions are met:
·
The ignition switch is ON for approximately 5 seconds or more.
·
The power source voltage of the clearance warning ECU assembly is 9 V or more. |
Turn the ignition switch to ON and wait for at least approximately 6 seconds. |
·
CSR OFF indicator light illuminates
·
PKSB OFF indicator light illuminates |
Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| Communication stops between the clearance warning ECU assembly and the TCM for aproximately 2 seconds or more. | Turn the ignition switch to ON and wait for at least approximately 7 seconds. | ||||||
| Either of the following conditions is met:
·
Communication stops between the clearance warning ECU assembly and the ECM for aproximately 5 seconds or more.*1
·
Communication stops between the clearance warning ECU assembly and the TCM for aproximately 5 seconds or more.*2 |
Turn the ignition switch to ON and wait for at least approximately 10 seconds. | ||||||
| U012987 | Lost Communication with Brake System Control Module Missing Message | Communication stops between the clearance warning ECU assembly and the brake actuator assembly (No. 2 skid control ECU) for aproximately 1 second or more. | All conditions are met:
·
The ignition switch is ON for approximately 3 seconds or more.
·
The power source voltage of the clearance warning ECU assembly is 9 V or more. |
Turn the ignition switch to ON and wait for at least approximately 4 seconds. |
·
CSR OFF indicator light illuminates
·
PKSB OFF indicator light illuminates |
Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| Communication stops between the clearance warning ECU assembly and the brake actuator assembly (No. 2 skid control ECU) for aproximately 2 seconds or more. | Turn the ignition switch to ON and wait for at least approximately 5 seconds. | ||||||
| Communication stops between the clearance warning ECU assembly and the brake actuator assembly (No. 2 skid control ECU) for aproximately 3 seconds or more. | Turn the ignition switch to ON and wait for at least approximately 6 seconds. | ||||||
| U110387 | Lost Communication with Stop and Start Control Module Missing Message | Communication stops between the clearance warning ECU assembly and the engine stop and start ECU for aproximately 1 second or more. | All conditions are met:
·
The ignition switch is ON for approximately 5 seconds or more.
·
The power source voltage of the clearance warning ECU assembly is 9 V or more. |
Turn the ignition switch to ON and wait for at least approximately 6 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| Communication stops between the clearance warning ECU assembly and the engine stop and start ECU for aproximately 5 seconds or more. | Turn the ignition switch to ON and wait for at least approximately 10 seconds. | ||||||
| U013187 | Lost Communication with Power Steering Control Module Missing Message | Communication stops between the clearance warning ECU assembly and the power steering ECU assembly for aproximately 1 second or more. | All conditions are met:
·
The ignition switch is ON for approximately 1 seconds or more.
·
The power source voltage of the clearance warning ECU assembly is 9 V or more. |
Turn the ignition switch to ON and wait for at least approximately 2 seconds. | - | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U014087 | Lost Communication with Body Control Module Missing Message | Communication stops between the clearance warning ECU assembly and the main body ECU (multiplex network body ECU) for aproximately 3 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 5 seconds or more.
·
The power source voltage of the clearance warning ECU assembly is 9 V or more. |
Turn the ignition switch to ON and wait for at least approximately 8 seconds | - | Advanced park
·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| Communication stops between the clearance warning ECU assembly and the main body ECU (multiplex network body ECU) for aproximately 5 seconds or more. | Turn the ignition switch to ON and wait for at least approximately 10 seconds | ||||||
| U012687 | Lost Communication with Steering Angle Sensor Module Missing Message | Communication stops between the clearance warning ECU assembly and the steering sensor for aproximately 1 second or more. | All conditions are met:
·
The ignition switch is ON for approximately 6 seconds or more.
·
The power source voltage of the clearance warning ECU assembly is 9 V or more. |
Turn the ignition switch to ON and wait for at least approximately 7 seconds |
·
CSR OFF indicator light illuminates
·
PKSB OFF indicator light illuminates |
Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| Communication stops between the clearance warning ECU assembly and the steering sensor for aproximately 6 seconds or more. | Turn the ignition switch to ON and wait for at least approximately 12 seconds | ||||||
| U016487 | Lost Communication with HVAC Control Module Missing Message | Communication stops between the clearance warning ECU assembly and the air conditioning amplifier assembly for aproximately 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 5 seconds or more.
·
The power source voltage of the clearance warning ECU assembly is 9 V or more. |
Turn the ignition switch to ON and wait for at least approximately 10 seconds | - | Advanced park
·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U015587 | Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message | Communication stops between the clearance warning ECU assembly and the combination meter assembly for aproximately 3 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 5 seconds or more.
·
The power source voltage of the clearance warning ECU assembly is 9 V or more. |
Turn the ignition switch to ON and wait for at least approximately 8 seconds | - | Advanced park
·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| Communication stops between the clearance warning ECU assembly and the combination meter assembly for aproximately 5 seconds or more. | Turn the ignition switch to ON and wait for at least approximately 10 seconds | ||||||
| U023387 | Lost Communication with Side Obstacle Detection Control Module "B" Missing Message | Communication stops between the clearance warning ECU assembly and the blind spot monitor sensor LH for aproximately 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 5 seconds or more.
·
The power source voltage of the clearance warning ECU assembly is 9 V or more. |
Turn the ignition switch to ON and wait for at least approximately 10 seconds | - | - | DTC is stored until it is cleared using the GTS. |
| U110687 | Lost Communication with Electric Parking Brake Module Missing Message | Communication stops between the clearance warning ECU assembly and the brake actuator assembly (No.2 skid control ECU) for aproximately 2 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 2 seconds or more.
·
The power source voltage of the clearance warning ECU assembly is 9 V or more. |
Turn the ignition switch to ON and wait for at least approximately 4 seconds | - | Advanced park
·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
Main Body ECU (Multiplex Network Body ECU) / GTS Display "Main Body"
DTC communication uses the CAN communication system.
*1: for 1GR-FE
*2: except 1GR-FE
*3: w/ Audio and Visual System (for Radio and Display Type, for 12.3 Inch Display)
*4: w/ Audio and Visual System (for Radio and Display Type, except 12.3 Inch Display)
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U010087 | Lost Communication with ECM/PCM "A" Missing Message | Communication stops between the main body ECU (multiplex network body ECU) and the ECM for approximately 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U010187 | Lost Communication with TCM Missing Message | Either of the following conditions is met:
·
Communication stops between the main body ECU (multiplex network body ECU) and the ECM for approximately 10 seconds or more.*1
·
Communication stops between the main body ECU (multiplex network body ECU) and the TCM for approximately 10 seconds or more.*2 |
All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U012087 | Lost Communication with Starter / Generator Control Module Missing Message | Communication stops between the main body ECU (multiplex network body ECU) and the certification ECU (smart key ECU assembly) for approximately 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U012687 | Lost Communication with Steering Angle Sensor Module Missing Message | Communication stops between the main body ECU (multiplex network body ECU) and the steering sensor for approximately 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U012987 | Lost Communication with Brake System Control Module "A" Missing Message | Communication stops between the main body ECU (multiplex network body ECU) and the brake actuator assembly (No. 2 skid control ECU) for approximately 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U015187 | Lost Communication with Restraints Control Module Missing Message | Communication stops between the main body ECU (multiplex network body ECU) and the airbag ECU assembly for approximately 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U015587 | Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message | Communication stops between the main body ECU (multiplex network body ECU) and the combination meter assembly for approximately 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U016387 | Lost Communication with Navigation Control Module Missing Message | Either of the following conditions is met:
·
Communication stops between the main body ECU (multiplex network body ECU) and the radio receiver assembly for approximately 10 seconds or more.*3
·
Communication stops between the main body ECU (multiplex network body ECU) and the radio and display receiver assembly for approximately 10 seconds or more.*4 |
All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U016487 | Lost Communication with HVAC Control Module Missing Message | Communication stops between the main body ECU (multiplex network body ECU) and the air conditioning amplifier assembly for approximately 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U016887 | Lost Communication with Vehicle Security Control Module Missing Message | Communication stops between the main body ECU (multiplex network body ECU) and the certification ECU (smart key ECU assembly) for approximately 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U019987 | Lost Communication with "Door Control Module A" Missing Message | Communication stops between the main body ECU (multiplex network body ECU) and the outer mirror control ECU assembly RH for approximately 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U020087 | Lost Communication with "Door Control Module B" Missing Message | Communication stops between the main body ECU (multiplex network body ECU) and the outer mirror control ECU assembly LH for approximately 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U020887 | Lost Communication with "Seat Control Module A" Missing Message | Communication stops between the main body ECU (multiplex network body ECU) and the position control ECU assembly for approximately 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U023087 | Lost Communication with Rear Gate Module Missing Message | Communication stops between the main body ECU (multiplex network body ECU) and the multiplex network door ECU for approximately 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U023387 | Lost Communication with Side Obstacle Detection Control Module "B" Missing Message | Communication stops between the main body ECU (multiplex network body ECU) and the blind spot monitor sensor LH for approximately 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U023A87 | Lost Communication with Image Processing Module "A" Missing Message | Communication stops between the main body ECU (multiplex network body ECU) and the forward recognition camera for approximately 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U024187 | Lost Communication with Headlamp Control Module "A" Missing Message | Communication stops between the main body ECU (multiplex network body ECU) and the headlight ECU sub-assembly LH for approximately 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U110687 | Lost Communication with Electric Parking Brake Module Missing Message | Communication stops between the main body ECU (multiplex network body ECU) and the brake actuator assembly (No. 2 skid control ECU) for approximately 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U110787 | Lost Communication with Power Management Module Missing Message | Communication stops between the main body ECU (multiplex network body ECU) and the certification ECU (smart key ECU assembly) for approximately 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U111087 | Lost Communication with Clearance Sonar Module Missing Message | Communication stops between the main body ECU (multiplex network body ECU) and the clearance warning ECU assembly for approximately 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U111587 | Lost Communication with Tilt & Telescopic Module Missing Message | Communication stops between the main body ECU (multiplex network body ECU) and the multiplex tilt and telescopic ECU for approximately 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U111787 | Lost Communication with Accessory Gateway Missing Message | Communication stops between the main body ECU (multiplex network body ECU) and the option connector (bus buffer ECU) for approximately 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for approximately 10 seconds or more.
·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the ignition switch to ON and wait for at least approximately 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
Air Conditioning Amplifier Assembly / GTS Display "Air Conditioner"
DTC communication uses the CAN communication system.
*1: w/ Audio and Visual System (for Radio and Display Type, for 12.3 Inch Display)
*2: w/ Audio and Visual System (for Radio and Display Type, except 12.3 Inch Display)
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U010087 | Lost Communication with ECM/PCM "A" Missing Message | The air conditioning amplifier assembly does not receive data from the ECM for 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for 10 seconds or more.
·
The power source voltage of the air conditioning amplifier assembly is 10 V or higher. |
Turn the ignition switch to ON and wait at least 20 seconds. | MIL (malfunction indicator lamp) illuminates | - | DTC is stored until it is cleared using the GTS. |
| U013187 | Lost Communication with Power Steering Control Module Missing Message | The air conditioning amplifier assembly does not receive data from the power steering ECU assembly for 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for 10 seconds or more.
·
The power source voltage of the air conditioning amplifier assembly is 10 V or higher. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U014087 | Lost Communication with Body Control Module Missing Message | The air conditioning amplifier assembly does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for 10 seconds or more.
·
The power source voltage of the air conditioning amplifier assembly is 10 V or higher. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U015587 | Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message | The air conditioning amplifier assembly does not receive data from the combination meter assembly for 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for 10 seconds or more.
·
The power source voltage of the air conditioning amplifier assembly is 10 V or higher. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U016387 | Lost Communication with Navigation Control Module Missing Message | Either of the following conditions is met:
·
The air conditioning amplifier assembly does not receive data from the radio receiver assembly for 10 seconds or more.*1
·
The air conditioning amplifier assembly does not receive data from the radio and display receiver assembly for 10 seconds or more.*2 |
All conditions are met:
·
The ignition switch is ON for 10 seconds or more.
·
The power source voltage of the air conditioning amplifier assembly is 10 V or higher. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U020187 | Lost Communication with Navigation Control Module Missing Message | The air conditioning amplifier assembly does not receive data from the outer mirror control ECU assembly RH for 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for 10 seconds or more.
·
The power source voltage of the air conditioning amplifier assembly is 10 V or higher. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U020287 | Lost Communication with "Door Control Module D" Missing Message | The air conditioning amplifier assembly does not receive data from the outer mirror control ECU assembly LH for 10 seconds or more. | All conditions are met:
·
The ignition switch is ON for 10 seconds or more.
·
The power source voltage of the air conditioning amplifier assembly is 10 V or higher. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
Certification ECU (Smart Key ECU Assembly) / GTS Display "Entry&Start"
DTC communication uses the CAN communication system.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U010087 | Lost Communication with ECM/PCM "A" Missing Message | The certification ECU (smart key ECU assembly) does not receive data from the ECM for approximately 10 seconds or more. | All conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximate ly 10 seconds or more elapse.
·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the ignition switch to ON (IG) and wait for at least approxima tely 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U012987 | Lost Communication with Brake System Control Module "A" Missing Message | The certification ECU (smart key ECU assembly) does not receive data from the brake actuator assembly (No. 2 skid control ECU) for approximately 10 seconds or more. | All conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximate ly 10 seconds or more elapse.
·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the ignition switch to ON (IG) and wait for at least approxima tely 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U014087 | Lost Communication with Body Control Module Missing Message | The certification ECU (smart key ECU assembly) does not receive data from the main body ECU (multiplex network body ECU) for approximately 10 seconds or more. | All conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximate ly 10 seconds or more elapse.
·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the ignition switch to ON (IG) and wait for at least approxima tely 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U015587 | Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message | The certification ECU (smart key ECU assembly) does not receive data from the combination meter assembly for approximately 10 seconds or more. | All conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximate ly 10 seconds or more elapse.
·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the ignition switch to ON (IG) and wait for at least approxima tely 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U016487 | Lost Communication with HVAC Control Module Missing Message | The certification ECU (smart key ECU assembly) does not receive data from the air conditioning amplifier assembly for approximately 10 seconds or more. | All conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximate ly 10 seconds or more elapse.
·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the ignition switch to ON (IG) and wait for at least approxima tely 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U020187 | Lost Communication with "Door Control Module C" Missing Message | The certification ECU (smart key ECU assembly) does not receive data from the outer mirror control ECU assembly RH for approximately 10 seconds or more. | All conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximate ly 10 seconds or more elapse.
·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the ignition switch to ON (IG) and wait for at least approxima tely 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U020287 | Lost Communication with "Door Control Module D" Missing Message | The certification ECU (smart key ECU assembly) does not receive data from the outer mirror control ECU assembly LH for approximately 10 seconds or more. | All conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximate ly 10 seconds or more elapse.
·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the ignition switch to ON (IG) and wait for at least approxima tely 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U023087 | Lost Communication with Rear Gate Module Missing Message | The certification ECU (smart key ECU assembly) does not receive data from the multiplex network door ECU for approximately 10 seconds or more. | All conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximate ly 10 seconds or more elapse.
·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the ignition switch to ON (IG) and wait for at least approxima tely 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U110387 | Lost Communication with Stop and Start Control Module Missing Message | The certification ECU (smart key ECU assembly) does not receive data from the engine stop and start ECU for approximately 10 seconds or more. | All conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximate ly 10 seconds or more elapse.
·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the ignition switch to ON (IG) and wait for at least approxima tely 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
Certification ECU (Smart Key ECU Assembly) / GTS Display "Power Source Control"
DTC communication uses the CAN communication system.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U010087 | Lost Communication with ECM/PCM "A" Missing Message | The certification ECU (smart key ECU assembly) does not receive data from the ECM for approximately 10 seconds or more. | All conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximate ly 10 seconds or more elapse.
·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the ignition switch to ON (IG) and wait for at least approxima tely 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U012987 | Lost Communication with Brake System Control Module "A" Missing Message | The certification ECU (smart key ECU assembly) does not receive data from the brake actuator assembly (No. 2 skid control ECU) for approximately 10 seconds or more. | All conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximate ly 10 seconds or more elapse.
·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the ignition switch to ON (IG) and wait for at least approxima tely 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U014087 | Lost Communication with Body Control Module Missing Message | The certification ECU (smart key ECU assembly) does not receive data from the main body ECU (multiplex network body ECU) for approximately 10 seconds or more. | All conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximate ly 10 seconds or more elapse.
·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the ignition switch to ON (IG) and wait for at least approxima tely 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U015587 | Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message | The certification ECU (smart key ECU assembly) does not receive data from the combination meter assembly for approximately 10 seconds or more. | All conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximate ly 10 seconds or more elapse.
·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the ignition switch to ON (IG) and wait for at least approxima tely 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U016487 | Lost Communication with HVAC Control Module Missing Message | The certification ECU (smart key ECU assembly) does not receive data from the air conditioning amplifier assembly for approximately 10 seconds or more. | All conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximate ly 10 seconds or more elapse.
·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the ignition switch to ON (IG) and wait for at least approxima tely 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U110387 | Lost Communication with Stop and Start Control Module Missing Message | The certification ECU (smart key ECU assembly) does not receive data from the engine stop and start ECU for approximately 10 seconds or more. | All conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and approximate ly 10 seconds or more elapse.
·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the ignition switch to ON (IG) and wait for at least approxima tely 20 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
Position Control ECU Assembly / GTS Display "Driver Seat" (w/ Seat Position Memory System)
DTC communication uses the CAN communication system.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U0100 | Lost Communication with ECM/PCM "A" | Communication stops between the position control ECU assembly and the ECM for aproximately 10 seconds or more. | All conditions are met:
·
The ignition switch is ON.
·
The power source voltage of the position control ECU assembly is 8 V or more. |
Turn the ignition switch to ON and wait for at least approximately 10 seconds. | - | - | - |
| U0140 | Lost Communication with Body Control Module | Communication stops between the position control ECU assembly and the main body ECU (multiplex network body ECU) for aproximately 10 seconds or more. | The power source voltage of the position control ECU assembly is 8 V or more. | Turn the ignition switch to ON and wait for at least approximately 10 seconds. | - | - | - |
| U1115 | Lost Communication with Tilt & Telescopic Module | Communication stops between the position control ECU assembly and the multiplex tilt and telescopic ECU for aproximately 10 seconds or more. | The power source voltage of the position control ECU assembly is 8 V or more. | Turn the ignition switch to ON and wait for at least approximately 10 seconds. | - | - | - |
Multiplex Tilt and Telescopic ECU / GTS Display "Tilt&Telescopic" (w/ Power Tilt and PowerTelescopic Steering Column System)
DTC communication uses the CAN communication system.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Displayed | DTC Storage Method | |
|---|---|---|---|---|---|---|---|
| Indication in Meter | Multi-information Display | ||||||
| U014287 | Lost Communication with Body Control Module "B" Missing Message | Communication stops between the multiplex tilt and telescopic ECU and the main body ECU (multiplex network body ECU) for aproximately 4 seconds or more. | The power source voltage of the multiplex tilt and telescopic ECU is 9 V or more. | Turn the ignition switch to ON and wait for at least approximately 4 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U015587 | Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message | Communication stops between the multiplex tilt and telescopic ECU and the combination meter assembly for aproximately 10 seconds or more. | The power source voltage of the multiplex tilt and telescopic ECU is 9 V or more. | Turn the ignition switch to ON and wait for at least approximately 10 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
| U020887 | Lost Communication with "Seat Control Module A" Missing Message | Communication stops between the multiplex tilt and telescopic ECU and the position control ECU assembly for aproximately 10 seconds or more. | The power source voltage of the multiplex tilt and telescopic ECU is 9 V or more. | Turn the ignition switch to ON and wait for at least approximately 10 seconds. | - | - | DTC is stored until it is cleared using the GTS. |
Central Gateway ECU (Network Gateway ECU) / GTS Display "Central Gateway"
The central gateway ECU (network gateway ECU) is connected to the CAN communication system, but the central gateway ECU (network gateway ECU) does not store or output CAN communication DTCs.
Steering Sensor / GTS Display "Steering Angle Sensor"
The steering sensor is connected to the CAN communication system, but the steering sensor does not store or output CAN communication DTCs.
Bus Buffer ECU / GTS Display "-" (w/ Bus Buffer ECU)
The bus buffer ECU is connected to the CAN communication system, but the bus buffer ECU does not store or output CAN communication DTCs.
CAN BUS WAVEFORMS
This waveform is measured between terminals CANH and GND, and terminals CANL and GND of the central gateway ECU (network gateway ECU). (Use this as a reference for diagnosis of CAN communication lines.)
When malfunctions in multiple ECUs are suspected based on the CAN bus check and DTCs checked using the GTS, check the resistance of the CAN bus using an ohmmeter first. If no problems are found, check the following waveforms.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
If a waveform is not similar to one of the following 3 patterns (Group 1), then an open in a CAN main bus line, an open in a CAN branch line, or a short between a CAN line (CANH or CANL) and ground is suspected (Group 2).
Wiggle the connector and wire harness to check if the waveform changes.
CAN bus waveforms (Group 1)
Normal waveform
Open in both of the lines (CANH and CANL) of a CAN branch
Waveforms (waveforms shown using dotted lines) are not output from an ECU or sensor connected to a CAN branch with an open circuit in both lines. (Waveforms from other ECUs or sensors are normal.)
Because this waveform is similar to a normal waveform, instead of using the waveform, the malfunctioning part can be narrowed down by performing a CAN bus check.
Short between the CAN bus lines (CANH and CANL)
Waveforms disappear.
If the malfunction is in an ECU, disconnecting the ECU will change the waveform. If the waveform does not change, a malfunction in the wire harness is suspected.
CAN bus waveforms (reference) (Group 2)
The following CAN bus waveforms can be used only as reference. the actual measured waveform may differ significantly depending on the location of the open or short circuit.
Open in a CAN branch line (CANH)
An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.
Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. the waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.
Open in a CAN branch line (CANL)
An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.
Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. the waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.
Open in a CAN main bus line (CANH)
Waveforms of ECUs or sensors that are closer to the central gateway ECU (network gateway ECU) than the open part are almost normal.
Waveforms of ECUs or sensors that are on the opposite side of the central gateway ECU (network gateway ECU) from the open part are abnormal.
An open in a CAN main bus line can be confirmed by measuring the resistance between the CANH and CANL terminals of any CAN branch.
Short between a CAN bus line (CANH) and ground
Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connectors or when disconnecting ECUs or sensors.
A short to ground in the CANH line can be confirmed by measuring the resistance between CANH and ground using an ohmmeter.
Short between a CAN bus line (CANL) and ground
Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connectors or when disconnecting ECUs or sensors.
A short to ground in the CANL line can be confirmed by measuring the resistance between CANL and ground using an ohmmeter.