Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2022.11
RM38G0E _95 ADAS / AD _100650 ADVANCED DRIVER ASSISTANCE SYSTEM _0469138 DYNAMIC RADAR CRUISE CONTROL SYSTEM U

ADVANCED DRIVER ASSISTANCE SYSTEM  DYNAMIC RADAR CRUISE CONTROL SYSTEM  TERMINALS OF ECU  


CHECK ECM (for 1GR-FE)


C458640N01
2.229,0.281 2.615,0.542 0.385,0.26 5.427,0.281 5.813,0.542 0.385,0.26 2.302,0.333 2.615,0.542 0.313,0.208 10 false C92 5.542,0.333 5.854,0.542 0.313,0.208 10 false B2

HINT:

The standard voltage between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbols) Terminal Description Condition Specified Condition
B2-7 (STP) - C92-81 (E1) Stop light switch assembly signal Brake pedal depressed 11 to 14 V
Brake pedal released 0 to 1.5 V
B2-8 (ST1-) - C92-81 (E1) Stop light switch assembly signal Ignition switch ON, brake pedal depressed 0 to 1.5 V
Ignition switch ON, brake pedal released 11 to 14 V


CHECK ECM (for V35A-FTS)


B460712E28
5.49,0.917 5.823,1.156 0.333,0.24 2.01,0.917 2.344,1.156 0.333,0.24 3.885,0.927 4.219,1.167 0.333,0.24 5.583,0.969 6.042,1.167 0.458,0.198 10 false B1 2.073,0.969 2.531,1.167 0.458,0.198 10 false C37 3.938,0.979 4.396,1.177 0.458,0.198 10 false C38

HINT:

The standard voltage between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbols) Terminal Description Condition Specified Condition
B1-21 (ST1-) - B1-9 (E1) Stop light switch assembly signal Ignition switch ON, brake pedal depressed 0 to 1.5 V
Ignition switch ON, brake pedal released 11 to 14 V
B1-22 (STP) - B1-9 (E1) Stop light switch assembly signal Brake pedal depressed 11 to 14 V
Brake pedal released 0 to 1.5 V


CHECK FORWARD RECOGNITION CAMERA


NOTICE:
·

DTCs may be output when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the GTS once the inspection has been completed.

·

Do not apply excessive force to the forward recognition camera connector.



C497956E01
1.854,0.698 2.292,1.052 0.438,0.354 1.958,0.802 2.417,1 0.458,0.198 10 false d33

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
d33-7 (IGB) - d33-10 (GND) Power source Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
d33-10 (GND) - Body ground Ground Always Below 1 Ω