Home › Vehicle Exterior › MIRROR (EXT) › OUTER MIRROR SWITCH › from 2022.11
RM38G0E _59 Vehicle Exterior _100827 MIRROR (EXT) _0468035 OUTER MIRROR SWITCH G

MIRROR (EXT)  OUTER MIRROR SWITCH  INSPECTION  


PROCEDURE

Hide 84870A 1.INSPECT OUTER MIRROR SWITCH ASSEMBLY (for LHD, w/o Reverse Shift-linked Mirror)

a.

Check the mirror select switch and mirror surface adjust switch.

i.
B551925C09
1.51,2.302 1.906,2.552 0.396,0.25 2.385,1.146 3.031,1.146 true 1.938,3.594 2.156,2.938 true 1.813,3.573 1.948,2.896 true 1.594,3.552 1.469,2.865 true 1.479,3.552 1.052,2.865 true 1.271,3.552 0.708,2.875 true 1.458,3.854 1.177,4.292 true 2.094,3.813 2.438,4.271 true 2.125,3.542 2.563,3.052 true 1.24,3.854 0.729,4.323 true 0.313,1.26 0.958,1.26 true 1.604,3.844 1.427,4.333 true 1.792,3.813 1.729,4.323 true 3.115,1.063 3.427,1.26 0.313,0.198 10 false *a 0.115,1.146 0.427,1.344 0.313,0.198 10 false *b 2.188,2.75 2.5,2.948 0.313,0.198 10 false VL 1.865,2.708 2.177,2.906 0.313,0.198 10 false HR 1.385,2.677 1.698,2.875 0.313,0.198 10 false HL 0.917,2.677 1.229,2.875 0.313,0.198 10 false VR 0.594,2.719 0.906,2.917 0.313,0.198 10 false B 2.458,4.302 2.771,4.5 0.313,0.198 10 false E 1.073,4.323 1.385,4.521 0.313,0.198 10 false M+ 1.583,2.354 2.042,2.552 0.458,0.198 10 false N22 0.583,4.313 0.896,4.51 0.313,0.198 10 false ILL+ 2.604,2.885 2.917,3.083 0.313,0.198 10 false ILL- 0.167,2.417 0.479,2.615 0.313,0.198 10 false *c 1.323,4.344 1.635,4.542 0.313,0.198 10 false MR 1.635,4.354 1.948,4.552 0.313,0.198 10 false MF
*a Mirror Select and Surface Adjust Switch
*b Mirror Retract Switch
*c Component without harness connected
(Outer Mirror Switch Assembly)


Turn the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for Left Side):
Tester Connection Condition Specified Condition

Click Location & Routing(N22)Location & Routing

Click Connector(N22)Body>Front Door Wire LH>Outer Mirror Switch Assembly

N22-2 (VL) - N22-6 (B)
N22-11 (M+) - N22-7 (E)
Up Below 1 Ω
Off 10 kΩ or higher
N22-2 (VL) - N22-7 (E)
N22-11 (M+) - N22-6 (B)
Down Below 1 Ω
Off 10 kΩ or higher
N22-4 (HL) - N22-6 (B)
N22-11 (M+) - N22-7 (E)
Left Below 1 Ω
Off 10 kΩ or higher
N22-4 (HL) - N22-7 (E)
N22-11 (M+) - N22-6 (B)
Right Below 1 Ω
Off 10 kΩ or higher



iii.

Turn the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for Right Side):
Tester Connection Condition Specified Condition

Click Location & Routing(N22)Location & Routing

Click Connector(N22)Body>Front Door Wire LH>Outer Mirror Switch Assembly

N22-5 (VR) - N22-6 (B)
N22-11 (M+) - N22-7 (E)
Up Below 1 Ω
Off 10 kΩ or higher
N22-5 (VR) - N22-7 (E)
N22-11 (M+) - N22-6 (B)
Down Below 1 Ω
Off 10 kΩ or higher
N22-3 (HR) - N22-6 (B)
N22-11 (M+) - N22-7 (E)
Left Below 1 Ω
Off 10 kΩ or higher
N22-3 (HR) - N22-7 (E)
N22-11 (M+) - N22-6 (B)
Right Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



b.

Check the mirror retract switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N22)Location & Routing

Click Connector(N22)Body>Front Door Wire LH>Outer Mirror Switch Assembly

N22-9 (MF) - N22-6 (B)
N22-10 (MR) - N22-7 (E)
Driving position Below 1 Ω
N22-10 (MR) - N22-6 (B)
N22-9 (MF) - N22-7 (E)
Retract position Below 1 Ω




c.

Check that the LED illuminates.

i.

Apply battery voltage to the outer mirror switch assembly and check that the LED illuminates.

OK:
Tester Connection Specified Condition

Click Location & Routing(N22)Location & Routing

Click Connector(N22)Body>Front Door Wire LH>Outer Mirror Switch Assembly

Battery positive (+) - N22-12 (ILL+)
Battery negative (-) - N22-1 (ILL-)
LED illuminates


If the result is not as specified, replace the outer mirror switch assembly.



Hide 84870A 2.INSPECT OUTER MIRROR SWITCH ASSEMBLY (for LHD, w/ Reverse Shift-linked Mirror)

a.
B581958C28
1.583,2.5 1.938,2.781 0.354,0.281 2.083,1 2.344,0.385 true 1.448,3.563 0.75,3.115 true 1.604,3.563 1.292,2.938 true 2.385,4.302 2.115,3.865 true 1.344,4.313 1.615,3.833 true 1.792,4.292 1.792,3.844 true 2.083,4.313 1.958,3.833 true 2.146,3.573 2.583,2.917 true 0.75,4.292 1.26,3.833 true 0.958,1.188 0.531,1.188 true 2.333,0.281 2.667,0.531 0.333,0.25 10 false *a 0.177,2.302 0.531,2.51 0.354,0.208 10 false *c 0.344,3.01 0.76,3.26 0.417,0.25 10 false MSW 1.115,2.75 1.448,3 0.333,0.25 10 false M+ 2.417,4.333 2.667,4.583 0.25,0.25 10 false E 1.646,2.563 2.104,2.76 0.458,0.198 10 false N22 1.292,4.333 1.625,4.583 0.333,0.25 10 false MR 1.635,4.333 1.969,4.583 0.333,0.25 10 false MAT 2.052,4.333 2.385,4.583 0.333,0.25 10 false E 2.646,2.813 2.979,3.063 0.333,0.25 10 false ILL- 0.552,4.333 0.885,4.583 0.333,0.25 10 false ILL+ 0.365,1.083 0.698,1.333 0.333,0.25 10 false *b
*a Mirror Select and Surface Adjust Switch
*b Mirror Retract Switch
*c Component without harness connected
(Outer Mirror Switch Assembly)


Check the mirror select switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N22)Location & Routing

Click Connector(N22)Body>Front Door Wire LH>Outer Mirror Switch Assembly

N22-5 (MSW) - N22-7 (E) Mirror select switch turned to R position Below 10 Ω
Mirror select switch off 10 kΩ or higher
Mirror select switch turned to L position 90 to 110 Ω


If the result is not as specified, replace the outer mirror switch assembly.



b.

Check the mirror surface adjust switch.

i.

Turn the mirror select switch to the L or R position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N22)Location & Routing

Click Connector(N22)Body>Front Door Wire LH>Outer Mirror Switch Assembly

N22-4 (M+) - N22-7 (E) Mirror surface adjust switch pushed up 90 to 110 Ω
Mirror surface adjust switch pushed down 437 to 503 Ω
Mirror surface adjust switch pushed left 744 to 856 Ω
Mirror surface adjust switch pushed right 225 to 275 Ω
Mirror surface adjust switch not pushed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



c.

Check the mirror retract switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N22)Location & Routing

Click Connector(N22)Body>Front Door Wire LH>Outer Mirror Switch Assembly

N22-9 (MAT) - N22-8 (E) AUTO position Below 35 Ω
N22-9 (MAT) - N22-8 (E) Except AUTO position 10 kΩ or higher
N22-10 (MR) - N22-8 (E) Retract position Below 35 Ω
N22-10 (MR) - N22-8 (E) Except retract position 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



d.

Check that the LED illuminates.

i.

Apply battery voltage to the outer mirror switch assembly and check that the LED illuminates.

OK:
Tester Connection Specified Condition

Click Location & Routing(N22)Location & Routing

Click Connector(N22)Body>Front Door Wire LH>Outer Mirror Switch Assembly

Battery positive (+) - N22-12 (ILL+)
Battery negative (-) - N22-1 (ILL-)
LED illuminates


If the result is not as specified, replace the outer mirror switch assembly.



Hide 84870A 3.INSPECT OUTER MIRROR SWITCH ASSEMBLY (for RHD, w/o Reverse Shift-linked Mirror)

a.

Check the mirror select switch and mirror surface adjust switch.

i.
B551414C10
1.51,2.302 1.906,2.552 0.396,0.25 2.385,1.198 3.031,1.198 true 1.938,3.594 2.156,2.938 true 1.813,3.573 1.948,2.896 true 1.594,3.552 1.469,2.865 true 1.479,3.552 1.052,2.865 true 1.271,3.552 0.708,2.875 true 1.458,3.854 1.177,4.292 true 2.094,3.813 2.438,4.271 true 2.125,3.542 2.563,3.052 true 1.24,3.854 0.729,4.323 true 0.594,1.021 1.385,1.021 true 1.604,3.844 1.427,4.333 true 1.792,3.813 1.729,4.323 true 0.396,0.927 0.708,1.125 0.313,0.198 10 false *a 3.094,1.125 3.406,1.323 0.313,0.198 10 false *b 2.188,2.75 2.5,2.948 0.313,0.198 10 false VL 1.865,2.708 2.177,2.906 0.313,0.198 10 false HR 1.385,2.677 1.698,2.875 0.313,0.198 10 false HL 0.917,2.677 1.229,2.875 0.313,0.198 10 false VR 0.594,2.719 0.906,2.917 0.313,0.198 10 false B 2.458,4.302 2.771,4.5 0.313,0.198 10 false E 1.073,4.323 1.385,4.521 0.313,0.198 10 false M+ 1.583,2.354 2.042,2.552 0.458,0.198 10 false M22 0.583,4.313 0.896,4.51 0.313,0.198 10 false ILL+ 2.604,2.885 2.917,3.083 0.313,0.198 10 false ILL- 0.167,2.417 0.479,2.615 0.313,0.198 10 false *c 1.323,4.344 1.635,4.542 0.313,0.198 10 false MR 1.635,4.354 1.948,4.552 0.313,0.198 10 false MF
*a Mirror Select and Surface Adjust Switch
*b Mirror Retract Switch
*c Component without harness connected
(Outer Mirror Switch Assembly)


Turn the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for Left Side):
Tester Connection Condition Specified Condition

Click Location & Routing(M22)Location & Routing

Click Connector(M22)Body>Front Door Wire RH>Outer Mirror Switch Assembly

M22-2 (VL) - M22-6 (B)
M22-11 (M+) - M22-7 (E)
Up Below 1 Ω
Off 10 kΩ or higher
M22-2 (VL) - M22-7 (E)
M22-11 (M+) - M22-6 (B)
Down Below 1 Ω
Off 10 kΩ or higher
M22-4 (HL) - M22-6 (B)
M22-11 (M+) - M22-7 (E)
Left Below 1 Ω
Off 10 kΩ or higher
M22-4 (HL) - M22-7 (E)
M22-11 (M+) - M22-6 (B)
Right Below 1 Ω
Off 10 kΩ or higher



iii.

Turn the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for Right Side):
Tester Connection Condition Specified Condition

Click Location & Routing(M22)Location & Routing

Click Connector(M22)Body>Front Door Wire RH>Outer Mirror Switch Assembly

M22-5 (VR) - M22-6 (B)
M22-11 (M+) - M22-7 (E)
Up Below 1 Ω
Off 10 kΩ or higher
M22-5 (VR) - M22-7 (E)
M22-11 (M+) - M22-6 (B)
Down Below 1 Ω
Off 10 kΩ or higher
M22-3 (HR) - M22-6 (B)
M22-11 (M+) - M22-7 (E)
Left Below 1 Ω
Off 10 kΩ or higher
M22-3 (HR) - M22-7 (E)
M22-11 (M+) - M22-6 (B)
Right Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



b.

Check the mirror retract switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M22)Location & Routing

Click Connector(M22)Body>Front Door Wire RH>Outer Mirror Switch Assembly

M22-9 (MF) - M22-6 (B)
M22-10 (MR) - M22-7 (E)
Driving position Below 1 Ω
M22-10 (MR) - M22-6 (B)
M22-9 (MF) - M22-7 (E)
Retract position Below 1 Ω




c.

Check that the LED illuminates.

i.

Apply battery voltage to the outer mirror switch assembly and check that the LED illuminates.

OK:
Tester Connection Specified Condition

Click Location & Routing(M22)Location & Routing

Click Connector(M22)Body>Front Door Wire RH>Outer Mirror Switch Assembly

Battery positive (+) - M22-12 (ILL+)
Battery negative (-) - M22-1 (ILL-)
LED illuminates


If the result is not as specified, replace the outer mirror switch assembly.



Hide 84870A 4.INSPECT OUTER MIRROR SWITCH ASSEMBLY (for RHD, w/ Reverse Shift-linked Mirror)

a.
B533656C57
1.583,2.5 1.938,2.781 0.354,0.281 2.438,1.229 3.083,1.229 true 1.448,3.563 0.75,3.115 true 1.604,3.563 1.292,2.938 true 2.385,4.302 2.115,3.865 true 1.344,4.313 1.615,3.833 true 1.792,4.292 1.792,3.844 true 2.083,4.313 1.958,3.833 true 2.146,3.573 2.583,2.917 true 0.75,4.292 1.26,3.833 true 0.99,1.292 0.563,1.292 true 0.385,1.198 0.677,1.458 0.292,0.26 10 false *a 0.177,2.302 0.531,2.51 0.354,0.208 10 false *c 0.344,3.01 0.76,3.26 0.417,0.25 10 false MSW 1.115,2.75 1.448,3 0.333,0.25 10 false M+ 2.417,4.333 2.667,4.583 0.25,0.25 10 false E 1.646,2.563 2.104,2.76 0.458,0.198 10 false M22 1.292,4.333 1.625,4.583 0.333,0.25 10 false MR 1.635,4.333 1.969,4.583 0.333,0.25 10 false MAT 2.052,4.333 2.385,4.583 0.333,0.25 10 false E 2.646,2.813 2.979,3.063 0.333,0.25 10 false ILL- 0.552,4.333 0.885,4.583 0.333,0.25 10 false ILL+ 3.135,1.156 3.427,1.385 0.292,0.229 10 false *b
*a Mirror Select and Surface Adjust Switch
*b Mirror Retract Switch
*c Component without harness connected
(Outer Mirror Switch Assembly)


Check the mirror select switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M22)Location & Routing

Click Connector(M22)Body>Front Door Wire RH>Outer Mirror Switch Assembly

M22-5 (MSW) - M22-7 (E) Mirror select switch turned to R position Below 10 Ω
Mirror select switch off 10 kΩ or higher
Mirror select switch turned to L position 90 to 110 Ω


If the result is not as specified, replace the outer mirror switch assembly.



b.

Check the mirror surface adjust switch.

i.

Turn the mirror select switch to the L or R position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M22)Location & Routing

Click Connector(M22)Body>Front Door Wire RH>Outer Mirror Switch Assembly

M22-4 (M+) - M22-7 (E) Mirror surface adjust switch pushed up 90 to 110 Ω
Mirror surface adjust switch pushed down 437 to 503 Ω
Mirror surface adjust switch pushed left 744 to 856 Ω
Mirror surface adjust switch pushed right 225 to 275 Ω
Mirror surface adjust switch not pushed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



c.

Check the mirror retract switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M22)Location & Routing

Click Connector(M22)Body>Front Door Wire RH>Outer Mirror Switch Assembly

M22-9 (MAT) - M22-8 (E) AUTO position Below 35 Ω
M22-9 (MAT) - M22-8 (E) Except AUTO position 10 kΩ or higher
M22-10 (MR) - M22-8 (E) Retract position Below 35 Ω
M22-10 (MR) - M22-8 (E) Except retract position 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



d.

Check that the LED illuminates.

i.

Apply battery voltage to the outer mirror switch assembly and check that the LED illuminates.

OK:
Tester Connection Specified Condition

Click Location & Routing(M22)Location & Routing

Click Connector(M22)Body>Front Door Wire RH>Outer Mirror Switch Assembly

Battery positive (+) - M22-12 (ILL+)
Battery negative (-) - M22-1 (ILL-)
LED illuminates


If the result is not as specified, replace the outer mirror switch assembly.