Home › Vehicle Exterior › BODY PANEL › FRONT BODY PILLAR(for Regular Cab)
BM25T0E _01 Vehicle Exterior _030570 BODY PANEL _0137613 FRONT BODY PILLAR(for Regular Cab) F

BODY PANEL  FRONT BODY PILLAR(for Regular Cab)  CUT AND JOIN REPLACEMENT SECTIONS  


K109007

With the front fender apron assembly removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location
K108832

Brazing or Arc Brazing for Removal

a.

After removing the roof drip side channel front or roof drip channel, remove the front body pillar.

K117248C01
4.25,2.75 4.083,2.75 4.083,2.75 3.208,2.396 false 4.281,2.667 4.594,2.823 0.313,0.156 10 false *1 4.281,2.833 4.594,2.99 0.313,0.156 10 false *2 4.333,1.344 4.646,1.5 0.313,0.156 10 false *a
*1 ROOF DRIP SIDE CHANNEL FRONT(LH) *2 ROOF DRIP CHANNEL(RH)
*a 155 mm (6.10 in.) - -



b.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K117249C01
5.208,1.26 5.521,1.417 0.313,0.156 10 false *a
*a 70 mm (2.76 in.) - -
K108837

Adhesive - -


K117250C01
5.375,0.49 5.688,0.646 0.313,0.156 10 false *a
*a 45 mm (1.77 in.) - -


K117300C01
4.844,1.375 5.156,1.531 0.313,0.156 10 false *a
*a 100 mm (3.94 in.) - -


K117301C01
0.167,0.083 7,3.667 6.833,3.583 3.583,3.667 3.583,0.083 false 0.333,0.25 0.646,0.406 0.313,0.156 10 false *A 3.75,0.25 4.063,0.406 0.313,0.156 10 false *B
*A for Type A *B for Type B



c.

After removing the roof drip side channel front or roof drip channel, remove the front body pillar.

K117248C02
4.25,2.75 4.083,2.75 4.083,2.75 3.208,2.396 false 4.281,2.667 4.594,2.823 0.313,0.156 10 false *1 4.281,2.833 4.594,2.99 0.313,0.156 10 false *2 4.333,1.344 4.646,1.5 0.313,0.156 10 false *a 0.188,0.167 0.5,0.365 0.313,0.198 10 false *A
*A for Australia (2016/08-) - -
*1 ROOF DRIP SIDE CHANNEL FRONT(LH) *2 ROOF DRIP CHANNEL(RH)
*a 155 mm (6.10 in.) - -



d.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K148501C01
5.208,1.26 5.521,1.417 0.313,0.156 10 false *a 0.188,0.167 0.5,0.365 0.313,0.198 10 false *A
*A for Australia (2016/08-) - -
*a 70 mm (2.76 in.) - -
K108837

Adhesive - -


K148502C01
5.24,0.156 5.552,0.313 0.313,0.156 10 false *a 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A for Australia (2016/08-) - -
*a 40 mm (1.57 in.) - -


K148503C01
4.844,1.375 5.156,1.531 0.313,0.156 10 false *a 0.188,0.177 0.5,0.333 0.313,0.156 10 false *A
*A for Australia (2016/08-) - -
*a 150 mm (5.91 in.) - -




INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108825

Plug Weld
K108827

Cut and Join Location
K108830

Fillet Weld
K108831

Butt Weld
K108832

Braze
K108834

Body Sealer

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

If the entire supply part is not needed, remove the part of the supply part that is needed.

K117252C01
1.833,1.917 1.667,1.917 1.667,1.917 2.198,1.063 false 4.5,4.417 4.333,4.417 4.333,4.417 4.688,3.594 false 2.583,4.5 2.75,4.5 2.75,4.5 2.542,4.24 false 1.865,1.854 2.177,2.01 0.313,0.156 10 false *1 4.531,4.354 4.844,4.51 0.313,0.156 10 false *2 2.417,4.438 2.729,4.594 0.313,0.156 10 false *3 2.344,0.406 2.656,0.563 0.313,0.156 10 false *a 6,1.417 6.313,1.573 0.313,0.156 10 false *b 1.26,3.115 1.573,3.271 0.313,0.156 10 false *c
*1 ROCKER PANEL OUTER *2 FRONT BODY PILLAR SUB-ASSEMBLY OUTER
*3 FRONT BODY PILLAR SUB-ASSEMBLY INNER - -
*a 45 mm (1.77 in.) *b 70 mm (2.76 in.)
*c 100 mm (3.94 in.) - -



d.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K117253


e.

Before temporarily installing the new parts, weld the rocker panel outer, front body pillar sub-assembly outer, cowl side panel sub-assembly and front body pillar sub-assembly inner with the standard number of welding points.

K117254C01
2.083,3.917 1.917,3.917 1.917,3.917 1.698,3.479 false 3.573,2.594 3.917,2.25 3.917,2.25 4.083,2.25 false 1.25,0.917 1,0.5 1,0.5 0.833,0.5 false 4.583,5 4.417,5 4.417,5 4.198,4.563 false 2.115,3.854 2.427,4.01 0.313,0.156 10 false *1 0.667,0.438 0.979,0.594 0.313,0.156 10 false *2 4.615,4.938 4.927,5.094 0.313,0.156 10 false *3 4.115,2.188 4.427,2.344 0.313,0.156 10 false *4
*1 ROCKER PANEL OUTER *2 FRONT BODY PILLAR SUB-ASSEMBLY OUTER
*3 COWL SIDE PANEL SUB-ASSEMBLY *4 FRONT BODY PILLAR SUB-ASSEMBLY INNER



f.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K117255


g.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



K117256C01
0,0 0,0 false
K108837

Adhesive - -



h.

Weld the rocker panel outer, front body pillar sub-assembly outer, cowl side panel sub-assembly and front body pillar sub-assembly inner to the vehicle side.

K117257C01
2.333,1.083 2,0.75 2,0.75 1.833,0.75 false 2.542,2.917 3.083,2.667 3.083,2.667 3.25,2.667 false 1.583,1.833 1.25,1.521 1.25,1.521 1.083,1.521 false 5.531,1.417 5.833,1.083 5.833,1.083 6,1.083 false 3.281,2.594 3.594,2.75 0.313,0.156 10 false *1 1.667,0.677 1.979,0.833 0.313,0.156 10 false *2 0.938,1.427 1.25,1.583 0.313,0.156 10 false *3 6.031,1.01 6.344,1.208 0.313,0.198 10 false *4
*1 ROCKER PANEL OUTER *2 FRONT BODY PILLAR SUB-ASSEMBLY OUTER
*3 COWL SIDE PANEL SUB-ASSEMBLY *4 FRONT BODY PILLAR SUB-ASSEMBLY INNER


K117302

K117303C01
0.167,0.083 7,3.667 6.833,3.583 3.583,3.667 3.583,0.083 false 0.333,0.25 0.646,0.406 0.313,0.156 10 false *A 3.75,0.25 4.063,0.406 0.313,0.156 10 false *B 2.073,3.385 2.385,3.542 0.313,0.156 10 false *a
*A for Type A *B for Type B
*a 15 mm (0.59 in.) - -



i.

Weld the roof drip side channel front or roof drip channel to the vehicle side.

K117259C01
3.188,2.396 4.083,2.75 4.083,2.75 4.25,2.75 false 4.281,2.667 4.594,2.823 0.313,0.156 10 false *1 4.281,2.833 4.594,2.99 0.313,0.156 10 false *2
*1 ROOF DRIP SIDE CHANNEL FRONT(LH) *2 ROOF DRIP CHANNEL(RH)



j.

If the entire supply part is not needed, remove the part of the supply part that is needed.

K148504C01
1.833,1.917 1.667,1.917 1.667,1.917 2.198,1.063 false 4.5,4.417 4.333,4.417 4.333,4.417 4.688,3.594 false 2.583,4.406 2.75,4.406 2.75,4.406 2.542,4.146 false 1.865,1.854 2.177,2.01 0.313,0.156 10 false *1 4.531,4.354 4.844,4.51 0.313,0.156 10 false *2 2.396,4.323 2.708,4.479 0.313,0.156 10 false *3 2.354,0.344 2.667,0.5 0.313,0.156 10 false *a 6,1.417 6.313,1.573 0.313,0.156 10 false *b 1.25,3.156 1.563,3.313 0.313,0.156 10 false *c 0.188,0.167 0.5,0.323 0.313,0.156 10 false *A
*A for Australia (2016/08-) - -
*1 ROCKER PANEL OUTER *2 FRONT BODY PILLAR SUB-ASSEMBLY OUTER
*3 FRONT BODY PILLAR SUB-ASSEMBLY INNER - -
*a 40 mm (1.57 in.) *b 70 mm (2.76 in.)
*c 150 mm (5.91 in.) - -



k.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K148505C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A for Australia (2016/08-) - -



l.

Before temporarily installing the new parts, weld the rocker panel outer, front body pillar sub-assembly outer, cowl side panel sub-assembly, front body pillar sub-assembly inner and front pillar reinforcement sub-assembly lower with the standard number of welding points.

K148506C01
2.083,3.917 1.917,3.917 1.917,3.917 1.698,3.479 false 3.333,2.479 3.677,2.135 3.677,2.135 3.844,2.135 false 1.25,0.917 1,0.5 1,0.5 0.833,0.5 false 4.917,4.333 4.75,4.333 4.75,4.333 4.385,4.146 false 2.667,5.5 2.833,5.5 2.833,5.5 3.031,5.083 false 2.115,3.854 2.427,4.01 0.313,0.156 10 false *1 0.667,0.438 0.979,0.594 0.313,0.156 10 false *2 4.979,4.26 5.292,4.417 0.313,0.156 10 false *3 3.917,2.063 4.229,2.219 0.313,0.156 10 false *4 2.5,5.417 2.813,5.573 0.313,0.156 10 false *5 0.167,0.177 0.479,0.333 0.313,0.156 10 false *A
*A for Australia (2016/08-) - -
*1 ROCKER PANEL OUTER *2 FRONT BODY PILLAR SUB-ASSEMBLY OUTER
*3 COWL SIDE PANEL SUB-ASSEMBLY *4 FRONT BODY PILLAR SUB-ASSEMBLY INNER
*5 FRONT PILLAR REINFORCEMENT SUB-ASSEMBLY LOWER - -



m.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K148507C01
0.188,0.177 0.5,0.333 0.313,0.156 10 false *A
*A for Australia (2016/08-) - -



n.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



K148508C01
0.188,0.177 0.5,0.333 0.313,0.156 10 false *A
*A for Australia (2016/08-) - -
K108837

Adhesive - -



o.

Weld the rocker panel outer, front body pillar sub-assembly outer, cowl side panel sub-assembly and front body pillar sub-assembly inner to the vehicle side.

K148509C01
2.333,1.083 2,0.75 2,0.75 1.833,0.75 false 1.979,3.146 1.646,3.667 1.646,3.667 1.5,3.667 false 1.583,1.833 1.25,1.521 1.25,1.521 1.083,1.521 false 5.531,1.417 5.833,1.083 5.833,1.083 6,1.083 false 1.323,3.594 1.635,3.75 0.313,0.156 10 false *1 1.667,0.677 1.979,0.833 0.313,0.156 10 false *2 0.938,1.427 1.25,1.583 0.313,0.156 10 false *3 6.031,1.01 6.344,1.208 0.313,0.198 10 false *4 5.594,3.51 5.906,3.708 0.313,0.198 10 false *a 0.167,0.177 0.479,0.333 0.313,0.156 10 false *A
*A for Australia (2016/08-) - -
*1 ROCKER PANEL OUTER *2 FRONT BODY PILLAR SUB-ASSEMBLY OUTER
*3 COWL SIDE PANEL SUB-ASSEMBLY *4 FRONT BODY PILLAR SUB-ASSEMBLY INNER
*a 15 mm (0.59 in.) - -


K117302C03
0.188,0.167 0.5,0.323 0.313,0.156 10 false *A
*A for Australia (2016/08-) - -



p.

Weld the roof drip side channel front or roof drip channel to the vehicle side.

K117259C02
3.188,2.396 4.083,2.75 4.083,2.75 4.25,2.75 false 4.281,2.667 4.594,2.823 0.313,0.156 10 false *1 4.281,2.833 4.594,2.99 0.313,0.156 10 false *2 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A for Australia (2016/08-) - -
*1 ROOF DRIP SIDE CHANNEL FRONT(LH) *2 ROOF DRIP CHANNEL(RH)



q.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


r.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.