Home › Vehicle Exterior › BODY PANEL › FRONT BODY PILLAR(for 4 Door)
BM25T0E _01 Vehicle Exterior _030570 BODY WELD POINT _0137628 FRONT BODY PILLAR(for 4 Door) F

BODY WELD POINT  FRONT BODY PILLAR(for 4 Door)  CUT AND JOIN REPLACEMENT SECTIONS  


K109009

With the front fender apron assembly removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location
K108832

Brazing or Arc Brazing for Removal

a.

After removing the roof drip side channel front or roof drip channel, remove the front body pillar.

K117266C01
3.229,2.396 4.167,2.917 4.167,2.917 4.333,2.917 false 4.365,2.865 4.677,3.021 0.313,0.156 10 false *1 4.365,3.031 4.677,3.188 0.313,0.156 10 false *2 4.365,1.365 4.677,1.521 0.313,0.156 10 false *a
*1 ROOF DRIP SIDE CHANNEL FRONT(LH) *2 ROOF DRIP CHANNEL(RH)
*a 155 mm (6.10 in.) - -



b.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K117267C01
5.229,1.26 5.542,1.417 0.313,0.156 10 false *a
*a 70 mm (2.76 in.) - -
K108837

Adhesive - -


K117250C01
5.375,0.49 5.688,0.646 0.313,0.156 10 false *a
*a 45 mm (1.77 in.) - -


K117268C01
4.854,1.177 5.167,1.333 0.313,0.156 10 false *a
*a 100 mm (3.94 in.) - -




INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108825

Plug Weld
K108827

Cut and Join Location
K108830

Fillet Weld
K108831

Butt Weld
K108832

Braze
K108834

Body Sealer

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

If the entire supply part is not needed, remove the part of the supply part that is needed.

K117269C01
0.917,0.333 6.25,3.667 5.333,3.333 0.917,1.917 6.25,1.917 false 2.083,1.667 1.917,1.667 1.917,1.667 2.25,1.083 false 2.083,3.417 1.917,3.417 1.917,3.417 2.25,2.833 false 1.083,0.417 1.396,0.573 0.313,0.156 10 false *A 1.083,2.083 1.396,2.24 0.313,0.156 10 false *B 2.115,1.604 2.427,1.76 0.313,0.156 10 false *1 2.708,0.427 3.021,0.583 0.313,0.156 10 false *a 2.115,3.354 2.427,3.51 0.313,0.156 10 false *1 2.708,2.156 3.021,2.313 0.313,0.156 10 false *a
*A for Double Cab *B for 4 Door Van
*1 ROCKER PANEL OUTER - -
*a 45 mm (1.77 in.) - -


K117270C01
2.75,2.927 2.917,3.25 2.917,3.25 2.75,3.25 false 4.417,3.25 4.25,3.25 4.25,3.25 4.5,2.896 false 2.583,3.188 2.896,3.344 0.313,0.156 10 false *1 4.448,3.188 4.76,3.344 0.313,0.156 10 false *2 1.271,1.594 1.583,1.75 0.313,0.156 10 false *a 5.833,1.729 6.146,1.885 0.313,0.156 10 false *b
*1 FRONT BODY PILLAR SUB-ASSEMBLY INNER *2 FRONT BODY PILLAR UPPER OUTER
*a 100 mm (3.94 in.) *b 70 mm (2.76 in.)



d.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough body sealer and adhesive to the panels.



K117304C01
0,0 0,0 false
K108837

Adhesive - -



e.

Before temporarily installing the new parts, weld the front upper body pillar outer and No.1 pillar reinforcement lower with the standard number of welding points.

K117305C01
1.729,2.063 1.417,1.417 1.417,1.417 1.25,1.417 false 2.302,1.292 2.583,1 2.583,1 2.75,1 false 2.781,0.938 3.094,1.094 0.313,0.156 10 false *1 1.083,1.354 1.396,1.51 0.313,0.156 10 false *2
*1 FRONT BODY PILLAR UPPER OUTER *2 NO.1 PILLAR REINFORCEMENT LOWER



f.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K117271


g.

Before temporarily installing the new parts, weld the rocker panel outer, front body pillar upper outer, front body pillar sub-assembly outer, cowl side panel sub-assembly, front body pillar outer bracket and front body pillar sub-assembly inner with the standard number of welding points.

K117272C01
1.271,1.135 0.833,0.167 0.833,0.167 1,0.167 false 2.167,0.25 2.333,0.167 2.333,0.167 2.5,0.167 false 4.219,4.5 4.583,5 4.583,5 4.75,5 false 1.802,3.448 2.167,3.917 2.167,3.917 2.333,3.917 false 3.583,2.604 3.917,2.25 3.917,2.25 4.083,2.25 false 1.667,3.021 2,2.667 2,2.667 2.167,2.667 false 2.365,3.854 2.677,4.01 0.313,0.156 10 false *1 2.531,0.104 2.844,0.26 0.313,0.156 10 false *2 2.198,2.604 2.51,2.76 0.313,0.156 10 false *3 1.031,0.104 1.344,0.26 0.313,0.156 10 false *5 4.115,2.188 4.427,2.344 0.313,0.156 10 false *6 4.781,4.938 5.094,5.094 0.313,0.156 10 false *4
*1 ROCKER PANEL OUTER *2 FRONT BODY PILLAR UPPER OUTER
*3 FRONT BODY PILLAR SUB-ASSEMBLY OUTER *4 COWL SIDE PANEL SUB-ASSEMBLY
*5 FRONT BODY PILLAR OUTER BRACKET *6 FRONT BODY PILLAR SUB-ASSEMBLY INNER



h.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K117273


i.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



K117274C01
0,0 0,0 false
K108837

Adhesive - -



j.

Weld the rocker panel outer, front body pillar upper outer, front body pillar sub-assembly outer, cowl side panel sub-assembly, front body pillar outer bracket and front body pillar sub-assembly inner to the vehicle side.

K117275C01
1.583,1.833 1.281,1.51 1.281,1.51 1.115,1.51 false 2.229,1.969 2.563,1.635 2.563,1.635 2.729,1.635 false 2.594,2.906 2.896,2.698 2.896,2.698 3.063,2.698 false 2.365,1.01 2.021,0.667 2.021,0.667 1.854,0.667 false 2.073,1.573 2.552,1.26 2.552,1.26 2.719,1.26 false 5.583,1.5 5.833,1.25 5.833,1.25 6,1.25 false 1.688,0.583 2,0.74 0.313,0.156 10 false *2 2.781,1.563 3.094,1.719 0.313,0.156 10 false *3 0.948,1.427 1.26,1.583 0.313,0.156 10 false *4 2.781,1.167 3.094,1.323 0.313,0.156 10 false *5 3.125,2.615 3.438,2.771 0.313,0.156 10 false *1 6.052,1.167 6.365,1.323 0.313,0.156 10 false *6 5.51,3.531 5.823,3.729 0.313,0.198 10 false *a
*1 ROCKER PANEL OUTER *2 FRONT BODY PILLAR UPPER OUTER
*3 FRONT BODY PILLAR SUB-ASSEMBLY OUTER *4 COWL SIDE PANEL SUB-ASSEMBLY
*5 FRONT BODY PILLAR OUTER BRACKET *6 FRONT BODY PILLAR SUB-ASSEMBLY INNER
*a 15 mm (0.59 in.) - -


K117276


k.

Weld the roof drip side channel front or roof drip channel to the vehicle side.

K117277C01
3.208,2.396 4,2.75 4,2.75 4.167,2.75 false 4.198,2.688 4.51,2.844 0.313,0.156 10 false *1 4.198,2.854 4.51,3.01 0.313,0.156 10 false *2
*1 ROOF DRIP SIDE CHANNEL FRONT(LH) *2 ROOF DRIP CHANNEL(RH)



l.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


m.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.