Home › Vehicle Exterior › BODY PANEL › CENTER BODY PILLAR(for 4 Door)
BM25T0E _01 Vehicle Exterior _030570 BODY WELD POINT _0137629 CENTER BODY PILLAR(for 4 Door) F

BODY WELD POINT  CENTER BODY PILLAR(for 4 Door)  CUT AND JOIN REPLACEMENT SECTIONS  


K109010

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108827

Cut and Join Location

K117278C01
2.875,2.677 3.188,2.833 0.313,0.156 10 false *a
*a 370 mm (14.57 in.) - -


K117279C01
2.75,0.813 3.063,0.969 0.313,0.156 10 false *a 2.833,1.167 3.146,1.323 0.313,0.156 10 false *b 5.917,1 6.229,1.156 0.313,0.156 10 false *c
*a 30 mm (1.18 in.) *b 120 mm (4.72 in.)
*c 70 mm (2.76 in.) - -


a.

Carefully cut the center body pillar sub-assembly inner so not to damage A.

K117280C01
1.708,1.052 2.083,0.75 2.083,0.75 2.25,0.75 false 1.927,1.917 2.417,2.25 2.417,2.25 2.583,2.25 false 2.615,2.188 2.927,2.344 0.313,0.156 10 false *1 2.281,0.688 2.438,0.844 0.156,0.156 10 false A
*1 CENTER BODY PILLAR SUB-ASSEMBLY INNER - -




INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld
K108827

Cut and Join Location
K108831

Butt Weld
K108834

Body Sealer

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

If the entire supply part is not needed, remove the part of the supply part that is needed.

K117281C01
0.917,0.25 6.25,3.667 5.333,3.417 0.917,1.917 6.25,1.917 false 4.333,1.583 4.5,1.583 4.5,1.583 4.25,1.083 false 4.417,3.333 4.583,3.333 4.583,3.333 4.333,2.833 false 1.083,0.417 1.396,0.573 0.313,0.156 10 false *A 1.083,2.083 1.396,2.24 0.313,0.156 10 false *B 4.25,3.281 4.563,3.458 0.313,0.177 10 false *1 3.104,0.427 3.417,0.583 0.313,0.156 10 false *a 4.74,0.417 5.052,0.573 0.313,0.156 10 false *b 4.74,2.156 5.052,2.313 0.313,0.156 10 false *b 3.104,2.177 3.417,2.333 0.313,0.156 10 false *a 4.167,1.521 4.479,1.698 0.313,0.177 10 false *1
*A for Double Cab *B for 4 Door Van
*1 ROCKER PANEL OUTER - -
*a 370 mm (14.57 in.) *b 50 mm (1.97 in.)


K117282C01
1.167,3.417 1,3.417 1,3.417 1.625,2.333 false 5.688,2.417 6.25,3.417 6.25,3.417 6.083,3.417 false 1.198,3.354 1.51,3.51 0.313,0.156 10 false *1 5.917,3.354 6.229,3.51 0.313,0.156 10 false *2 1.333,0.844 1.646,1 0.313,0.156 10 false *a 5.906,1.146 6.219,1.302 0.313,0.156 10 false *b
*1 CENTER BODY PILLAR SUB-ASSEMBLY OUTER *2 CENTER BODY PILLAR SUB-ASSEMBLY INNER
*a 30 mm (1.18 in.) *b 150 mm (5.91 in.)



d.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K117283


e.

Before temporarily installing the new parts, weld the rocker panel outer, center body pillar sub-assembly outer, center body pillar sub-assembly inner, center body pillar reinforce sub-assembly lower and floor side reinforce sub-assembly inner with the standard number of welding points.

K117284C01
3.833,2.344 3.667,2.344 3.667,2.344 3.5,1.792 false 1.583,4.5 1.417,4.5 1.417,4.5 1.25,4 false 6.25,4.667 6.083,4.667 6.083,4.667 5.917,4.167 false 5.583,1.938 6.083,1.5 6.083,1.5 6.25,1.5 false 0.833,3 1,3 1,3 1.333,2.583 false 1.615,4.417 1.927,4.573 0.313,0.156 10 false *1 0.667,2.917 0.979,3.073 0.313,0.156 10 false *2 6.281,1.417 6.594,1.573 0.313,0.156 10 false *3 3.865,2.26 4.177,2.417 0.313,0.156 10 false *4 6.281,4.583 6.594,4.74 0.313,0.156 10 false *5
*1 ROCKER PANEL OUTER *2 CENTER BODY PILLAR SUB-ASSEMBLY OUTER
*3 CENTER BODY PILLAR SUB-ASSEMBLY INNER *4 CENTER BODY PILLAR REINFORCE SUB-ASSEMBLY LOWER
*5 FLOOR SIDE REINFORCE SUB-ASSEMBLY INNER - -



f.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K117285

K117286

K117287


g.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


h.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.