Home › Vehicle Exterior › BODY PANEL › FRONT DOOR OUTER PANEL(for 2 Door)
BM25T0E _01 Vehicle Exterior _030570 BODY WELD POINT _0137630 FRONT DOOR OUTER PANEL(for 2 Door) F

BODY WELD POINT  FRONT DOOR OUTER PANEL(for 2 Door)  ASSEMBLY REPLACEMENT  


K109011

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108832

Brazing or Arc Brazing for Removal

a.

Before removing the outer panel, mark the installation position with tape.

HINT:

Before removing the outer panel, establish its exact position in relation to the window frame using a reference marker, etc.


K117887C01
4.667,1.188 5,0.833 5,0.833 5.167,0.833 false 5.198,0.76 5.51,0.917 0.313,0.156 10 false *a 4.188,1.417 4.5,1.573 0.313,0.156 10 false *b
*a Positioning Tape *b Installation Position



b.

A is reused.

i.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K117889C01
1.896,2.583 2.063,2.583 2.063,2.583 2.917,1.917 false 1.76,2.5 1.917,2.698 0.156,0.198 10 false A
K108837

Adhesive - -




c.

After grinding off the hemming location, remove the outer panel.

K117888C01
6.25,3.063 6.583,3.417 6.583,3.417 6.75,3.417 false 6.781,3.354 7.094,3.51 0.313,0.156 10 false *a 6.125,0.938 6.438,1.094 0.313,0.156 10 false *b
*a Disc Sander *b Hemming Location




INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108825

Plug Weld
K108832

Braze
K108833

Spot MIG Weld
K108834

Body Sealer

a.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:

Apply enough adhesive to the panels.


K117214C01
0,0 0,0 false
K108837

Adhesive - -



b.

Before temporarily installing the new parts, weld the front door panel outer and A with the standard number of welding points.

K117890C01
3.25,3.333 3.083,3.333 3.083,3.333 3.375,2.938 false 2,2.25 2.167,2.25 2.167,2.25 2.958,1.448 false 3.281,3.271 3.594,3.427 0.313,0.156 10 false *1 1.833,2.188 1.99,2.385 0.156,0.198 10 false A
*1 FRONT DOOR PANEL OUTER - -



c.

Before temporarily installing the new parts, apply body sealer to the side impact protection beam and backside of the new parts.

NOTICE:

Do not close the drain hole.


HINT:

Apply sealer evenly about 10 mm (0.39 in.) from the flange and 3 mm (0.12 in.) in diameter on the outer panel and apply just enough sealer for the reinforcement and side impact protection beam to make contact.


K117891C01
6.073,3.073 6.385,3.229 0.313,0.156 10 false *a 5.323,1.406 5.635,1.563 0.313,0.156 10 false *b
*a Drain Hole *b 10 mm (0.39 in.)



d.

Bend the flange hem with a wooden hammer and dolly.

HINT:

Bend the panel gradually so as not to distort it.


K117892C01
6.01,5.25 6.333,4.917 6.333,4.917 6.5,4.917 false 5,6.417 5.167,6.417 5.167,6.417 5.51,6.083 false 6.167,5.833 6.5,6.167 6.5,6.167 6.667,6.167 false 3.583,1.833 3.917,1.5 3.917,1.5 4.083,1.5 false 4.115,1.427 4.427,1.583 0.313,0.156 10 false *a 6.531,4.844 6.844,5 0.313,0.156 10 false *b 6.698,6.094 7.01,6.25 0.313,0.156 10 false *c 4.833,6.333 5.146,6.49 0.313,0.156 10 false *d
*a Positioning Tape *b Cloth Tape
*c Dolly *d Wooden Hammer



e.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


f.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.