Home › Vehicle Exterior › BODY PANEL › REAR DOOR OUTER PANEL(for 4 Door)
BM25T0E _01 Vehicle Exterior _030570 BODY WELD POINT _0137631 REAR DOOR OUTER PANEL(for 4 Door) F

BODY WELD POINT  REAR DOOR OUTER PANEL(for 4 Door)  ASSEMBLY REPLACEMENT  


K109013

REMOVAL


Symbol Meaning
K108820

Remove Weld Points
K108832

Brazing or Arc Brazing for Removal

a.

Before removing the outer panel, mark the installation position with tape.

HINT:

Before removing the outer panel, establish its exact position in relation to the window frame using a reference marker, etc.


K117899C01
2.25,0.833 2.417,0.833 2.417,0.833 2.771,1.198 false 2.083,0.76 2.396,0.917 0.313,0.156 10 false *a 3.135,1.417 3.448,1.573 0.313,0.156 10 false *b
*a Positioning Tape *b Installation Position



b.

After grinding off the hemming location, remove the outer panel.

K117900C01
6.75,3.917 6.583,3.917 6.583,3.917 6.25,3.563 false 6.781,3.854 7.094,4.01 0.313,0.156 10 false *a 6.125,1.417 6.438,1.573 0.313,0.156 10 false *b
*a Disc Sander *b Hemming Location




INSTALLATION


Symbol Meaning
K108825

Plug Weld
K108832

Braze
K108833

Spot MIG Weld
K108834

Body Sealer

a.

Before temporarily installing the new parts, apply body sealer to the side impact protection beam and backside of the new parts.

NOTICE:

Do not close the drain hole.


HINT:

Apply sealer evenly about 10 mm (0.39 in.) from the flange and 3 mm (0.12 in.) in diameter on the outer panel and apply just enough sealer for the reinforcement to make contact.


K117901C01
2.833,2.917 2.667,2.917 2.667,2.917 2.333,2.583 false 2.865,2.854 3.177,3.01 0.313,0.156 10 false *1 6.073,3.063 6.385,3.219 0.313,0.156 10 false *a 5.323,1.385 5.635,1.542 0.313,0.156 10 false *b
*1 REAR DOOR PANEL OUTER - -
*a Drain Hole *b 10 mm (0.39 in.)



b.

Bend the flange hem with a wooden hammer and dolly.

HINT:

Bend the panel gradually so as not to distort it.


K117902C01
6.583,6 6.417,6 6.417,6 6.198,5.583 false 6,5.25 6.333,4.917 6.333,4.917 6.5,4.917 false 5.333,6.417 5.167,6.417 5.167,6.417 5.5,6.083 false 1.167,1.583 1.333,1.583 1.333,1.583 1.604,1.99 false 1,1.5 1.313,1.656 0.313,0.156 10 false *a 6.531,4.844 6.844,5 0.313,0.156 10 false *b 6.615,5.927 6.927,6.083 0.313,0.156 10 false *c 5.365,6.344 5.677,6.5 0.313,0.156 10 false *d
*a Positioning Tape *b Cloth Tape
*c Dolly *d Wooden Hammer



c.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


d.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.