With the quarter panel cut and join replacement sections removed.
REMOVAL
| Symbol Meaning | |
|---|---|
|
Remove Weld Points |
|
Remove Weld Points |
|
Remove Weld Points |
After removing the A, remove the quarter panel.
A is reused.
Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.
In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.
| *A | LH | - | - |
| *1 | QUARTER PANEL | - | - |
|
Adhesive | - | - |
| *A | LH | *B | for Type A |
| *A | LH | *B | for Type B |
| *A | LH | - | - |
After removing the A, remove the quarter panel.
A is reused.
Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.
In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.
| *A | RH | - | - |
| *1 | QUARTER PANEL | - | - |
|
Adhesive | - | - |
| *A | RH | *B | for Type A |
| *A | RH | *B | for Type B |
| *A | RH | *B | for Type C |
| *A | RH | *B | for Type D |
| *A | RH | - | - |
INSTALLATION
| Symbol Meaning | |
|---|---|
|
Spot Weld |
|
Plug Weld |
|
Plug Weld |
|
Plug Weld |
|
Body Sealer |
|
Assembly Mark |
Before installing a new part, apply body sealer.
Apply body sealer in an even, continuous bead.
| *A | LH | - | - |
For positioning of the new parts, align the installation standard holes of the outer panel and the inner panel.
| *A | LH | *B | for Type A |
| *1 | QUARTER PANEL | - | - |
| *A | LH | *B | for Type B |
| *1 | QUARTER PANEL | - | - |
| *A | LH | - | - |
Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).
Apply enough adhesive to the panels.
| *A | LH | - | - |
|
Adhesive | - | - |
After welding the quarter panel to the vehicle side, install the A.
| *A | LH | - | - |
| *1 | QUARTER PANEL | - | - |
Before installing a new part, apply body sealer.
Apply body sealer in an even, continuous bead.
| *A | RH | *B | for Type A |
For positioning of the new parts, align the installation standard holes of the outer panel and the inner panel.
| *A | RH | *B | for Type A |
| *1 | QUARTER PANEL | *2 | WELD BOLTS |
Before installing a new part, apply body sealer.
Apply body sealer in an even, continuous bead.
| *A | RH | *B | for Type B |
For positioning of the new parts, align the installation standard holes of the outer panel and the inner panel.
| *A | RH | *B | for Type B |
| *1 | QUARTER PANEL | *2 | WELD BOLTS |
Before installing a new part, apply body sealer.
Apply body sealer in an even, continuous bead.
| *A | RH | *B | for Type C |
For positioning of the new parts, align the installation standard holes of the outer panel and the inner panel.
| *A | RH | *B | for Type C |
| *1 | QUARTER PANEL | *2 | WELD BOLTS |
Before installing a new part, apply body sealer.
Apply body sealer in an even, continuous bead.
| *A | RH | *B | for Type D |
For positioning of the new parts, align the installation standard holes of the outer panel and the inner panel.
| *A | RH | *B | for Type D |
| *1 | QUARTER PANEL | *2 | WELD BOLTS |
| *A | RH | - | - |
Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).
Apply enough adhesive to the panels.
| *A | RH | - | - |
|
Adhesive | - | - |
After welding the quarter panel to the vehicle side, install the A.
| *A | RH | - | - |
| *1 | QUARTER PANEL | - | - |
After welding, apply undercoating to the corresponding parts. (See the painting / coating)
After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.