Home › Vehicle Exterior › BODY DIMENSIONS › MEASURING INFORMATION
BM25T0E _01 Vehicle Exterior _030690 BODY DIMENSIONS _0138308 MEASURING INFORMATION F

BODY DIMENSIONS  MEASURING INFORMATION  DIAGRAM DESCRIPTION  


HINT:
·

There are two types of dimensions in the diagram.

·

In cases in which only one dimension is given, left and right are symmetrical.

·

For symbols, capital letters indicate right side of vehicle, small letters indicate left side of vehicle (seen from rear).



Three-Dimensional Distance


K104022C04
1.615,0.135 1.844,0.292 0.229,0.156 10 true *a
*a Distance between the centers of the measuring points


a.

Straight-line distance between the centers of two measuring points.



Two-Dimensional Distance


K118753C01
1.771,0.094 2.083,0.25 0.313,0.156 10 false *a 1.271,1.344 1.583,1.5 0.313,0.156 10 false *b 1.854,1.344 2.167,1.5 0.313,0.156 10 false *c 1.021,1.917 1.333,2.073 0.313,0.156 10 false *d
*a Center-to-center horizontal distance in forward/rearward
*b Vertical distance to center
*c Vertical distance to lower surface
*d Imaginary Datum Line


a.

Horizontal distance in forward/rearward between the centers of two measuring points.


b.

Distance from the Imaginary Datum Line.



Imaginary Datum Line


K108803C02
2.75,1.042 3.063,1.198 0.313,0.156 10 false *a 1.073,1.563 1.385,1.719 0.313,0.156 10 false *b
*a 300 mm (11.81 in.)
*b Imaginary Datum Line


a.

The imaginary datum line when measuring the height is below 300 mm (11.81 in.) from the upperface on the center of the flame.



Measurement


K111554C01
0.083,2.833 1.667,4.583 1.583,1.75 1.75,2.833 3.333,4.583 1.583,1.75 0.833,0.75 1,0.75 1,0.75 1.25,1 false 0.667,1.833 0.396,1.833 false 2.25,1.833 2.25,2.083 false 1.167,3.917 0.885,3.917 false 2.833,3.917 2.563,3.917 false 0.667,0.677 0.979,0.833 0.313,0.156 10 false *a 2.177,2.125 2.49,2.281 0.313,0.156 10 false *b 0.75,1.75 1.063,1.906 0.313,0.156 10 false *c 0.167,2.927 0.479,3.083 0.313,0.156 10 false *d 1.833,2.917 2.146,3.073 0.313,0.156 10 false *e 1.25,3.844 1.563,4 0.313,0.156 10 false *c 2.917,3.833 3.229,3.99 0.313,0.156 10 false *c
*a Tracking Gauge
*b Master Gauge
*c Pointer
*d Wrong
*e Correct


a.

Basically, all measurements are to be done with a tracking gauge. For portions where it is not possible to use a tracking gauge, a tape measure should be used.


b.

Use only a tracking gauge that has no looseness in the body, measuring plate, or pointers.


c.

When using a tape measure, avoid twists and bends in the tape.

HINT:
·

The height of the left and right pointers must be equal.

·

Always calibrate the tracking gauge before measuring or after adjusting the pointer height.

·

Take care not to drop the tracking gauge or otherwise shock it.

·

Confirm that the pointers are securely in the holes.