Home › Vehicle Exterior › BODY PANEL › BACK PANEL(for Double Cab)
BM25T0E _01 Vehicle Exterior _030570 BODY WELD POINT _0138328 BACK PANEL(for Double Cab) F

BODY WELD POINT  BACK PANEL(for Double Cab)  CUT AND JOIN REPLACEMENT SECTIONS  


K109035

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108827

Cut and Join Location

K118320C01
1.76,0.75 2.073,0.906 0.313,0.156 10 false *a 5.24,0.76 5.552,0.917 0.313,0.156 10 false *a
*a 240 mm (9.45 in.) - -


K118321C01
0.25,0.167 0.563,0.323 0.313,0.156 10 false *A
*A LH Side - -


K118322C01
0.25,0.167 0.563,0.323 0.313,0.156 10 false *A
*A RH Side - -



INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108827

Cut and Join Location
K108831

Butt Weld

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

If the entire supply part is not needed, remove the part of the supply part that is needed.

K118323C01
1.854,1.115 2.167,1.271 0.313,0.156 10 false *a 5.167,1.125 5.479,1.281 0.313,0.156 10 false *a
*a 240 mm (9.45 in.) - -



c.

Before temporarily installing the new parts, weld the back panel, cab back reinforcement sub-assembly lower, cab rear pillar plate lower, back reinforcement lower, tool bag band bracket, jack handle spring sub-assembly and clamp with the standard number of welding points.

K118324C01
4.333,3.5 5.5,3.833 5.5,3.833 5.667,3.833 false 2.833,2.583 2.667,2.583 2.667,2.583 2.917,1.365 false 5.417,1.917 5.25,1.917 5.25,1.917 4.917,1.5 false 2.167,2.583 2,2.583 2,2.583 2.26,2.146 false 4.833,4.75 4.667,4.75 4.667,4.75 4.573,3.927 false 2.896,0.771 2.667,0.25 2.667,0.25 2.833,0.25 false 4.792,3.781 5.5,4.167 5.5,4.167 5.667,4.167 false 4.333,4.75 4.167,4.75 4.167,4.75 4.063,3.927 false 3.333,4.5 3.5,4.5 3.5,4.5 3.823,3.979 false 5.469,1.833 5.781,1.99 0.313,0.156 10 false *1 2.885,2.5 3.198,2.656 0.313,0.156 10 false *2 2.208,2.5 2.521,2.656 0.313,0.156 10 false *3 2.865,0.167 3.177,0.323 0.313,0.156 10 false *4 5.708,3.75 6.021,3.906 0.313,0.156 10 false *5 3.188,4.427 3.5,4.583 0.313,0.156 10 false *6 4.365,4.656 4.677,4.813 0.313,0.156 10 false *7 5.708,4.073 6.021,4.229 0.313,0.156 10 false *6 4.865,4.667 5.177,4.823 0.313,0.156 10 false *7
*1 BACK PANEL *2 CAB BACK REINFORCEMENT SUB-ASSEMBLY LOWER
*3 CAB REAR PILLAR PLATE LOWER *4 BACK REINFORCEMENT LOWER
*5 TOOL BAG BAND BRACKET *6 JACK HANDLE SPRING SUB-ASSEMBLY
*7 CLAMP - -


K118325

K118326C01
0.25,0.167 0.563,0.323 0.313,0.156 10 false *A
*A LH Side - -


K118327C01
0.25,0.167 0.563,0.323 0.313,0.156 10 false *A
*A RH Side - -



d.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


e.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.