Home › Vehicle Exterior › BODY PANEL › QUARTER PANEL (for 4 Door Steel Roof Van) › 2014.08–2021.01
BM25T0E _01 Vehicle Exterior _030570 BODY WELD POINT _0138537 QUARTER PANEL(for 4 Door Steel Roof Van) F

BODY WELD POINT  QUARTER PANEL(for 4 Door Steel Roof Van)  CUT AND JOIN REPLACEMENT SECTIONS  


K109020

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108827

Cut and Join Location

K118159

K118160C01
1.188,0.885 1.5,1.042 0.313,0.156 10 false *a 4.677,1 4.99,1.156 0.313,0.156 10 false *a
*a 200 mm (7.87 in.) - -


K118161C01
0.25,0.583 6.917,3.333 6.667,2.75 3.583,0.583 3.583,3.333 false 0.417,0.677 0.729,0.833 0.313,0.156 10 false *A 3.75,0.667 4.063,0.823 0.313,0.156 10 false *B
*A LH *B RH


K118162

K118163C01
4.083,0.167 6.833,4.583 2.75,4.417 4.083,2.417 6.833,2.417 false 4.167,0.25 4.479,0.406 0.313,0.156 10 false *A 4.167,2.51 4.479,2.667 0.313,0.156 10 false *B
*A LH *B RH


K118164


INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108831

Butt Weld
K108834

Body Sealer

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

Before installing a new part, apply body sealer.

HINT:
·

Apply body sealer evenly about 5 mm (0.20 in.) from the flange, avoiding any oozing.

·

Apply body sealer evenly, about 3 to 4 mm (0.12 to 0.16 in.) in diameter.



K118165C01
5.573,2.292 5.885,2.448 0.313,0.156 10 false *a
*a 5 mm (0.20 in.) - -



d.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K118166

K118167C01
3.417,2.604 3.667,3.271 3.667,3.271 3.833,3.271 false 3.865,3.188 4.177,3.344 0.313,0.156 10 false *1
*1 QUARTER PANEL - -


K118168C01
4,1.427 4.333,0.583 4.333,0.583 4.5,0.583 false 0.25,0.167 0.563,0.323 0.313,0.156 10 false *A 4.552,0.5 4.865,0.656 0.313,0.156 10 false *1
*A RH - -
*1 FUEL FILLER OPENING LID SUB-ASSEMBLY - -


K118169C01
0.25,0.583 6.917,3.333 6.667,2.75 3.583,3.333 3.583,0.583 false 0.417,0.667 0.729,0.823 0.313,0.156 10 false *A 3.75,0.667 4.063,0.823 0.313,0.156 10 false *B
*A LH *B RH


K118170

K118171C01
4.083,0.167 6.75,4.583 2.667,4.417 4.083,2.417 6.75,2.417 false 4.167,0.25 4.479,0.406 0.313,0.156 10 false *A 4.167,2.51 4.479,2.667 0.313,0.156 10 false *B
*A LH *B RH


K118172


e.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


f.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.