Home › Vehicle Exterior › BODY PANEL › BACK DOOR OPENING TROUGH(for 4 Door Steel Roof Van)
BM25T0E _01 Vehicle Exterior _030570 BODY WELD POINT _0138538 BACK DOOR OPENING TROUGH(for 4 Door Steel Roof Van) F

BODY WELD POINT  BACK DOOR OPENING TROUGH(for 4 Door Steel Roof Van)  CUT AND JOIN REPLACEMENT SECTIONS  


K109025

With the quarter panel cut and join replacement sections removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108827

Cut and Join Location

K118528C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 1.438,0.51 1.75,0.667 0.313,0.156 10 false *a
*A LH - -
*a 50 mm (1.97 in.) - -


K118529C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A LH - -


K118530C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 2.25,0.51 2.563,0.667 0.313,0.156 10 false *a
*A RH - -
*a 50 mm (1.97 in.) - -


K118531C01
0.167,0.177 0.479,0.333 0.313,0.156 10 false *A
*A RH - -


K118532C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A RH - -



INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108825

Plug Weld
K108831

Butt Weld

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

K118533C01
1.25,3.583 1.417,3.583 1.417,3.583 1.677,3.104 false 0.167,0.177 0.479,0.333 0.313,0.156 10 false *A 1.073,3.5 1.385,3.656 0.313,0.156 10 false *1
*A LH - -
*1 REAR PILLAR REINFORCE SUB-ASSEMBLY UPPER - -


K118534C01
0.167,0.177 0.479,0.333 0.313,0.156 10 false *A
*A LH - -


K118535C01
2.5,3.583 2.333,3.583 2.333,3.583 2.125,3.115 false 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 2.563,3.51 2.875,3.667 0.313,0.156 10 false *1
*A RH - -
*1 REAR PILLAR REINFORCE SUB-ASSEMBLY UPPER - -


K118536C01
0.167,0.177 0.479,0.333 0.313,0.156 10 false *A
*A RH - -


K118537C01
0.167,0.177 0.479,0.333 0.313,0.156 10 false *A
*A RH - -



c.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


d.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.