Home › Vehicle Exterior › BODY PANEL › FRONT BODY PILLAR(for 2 Door Short Rug Roof Van)
BM25T0E _01 Vehicle Exterior _030570 BODY WELD POINT _0138773 FRONT BODY PILLAR(for 2 Door Short Rug Roof Van) F

BODY WELD POINT  FRONT BODY PILLAR(for 2 Door Short Rug Roof Van)  CUT AND JOIN REPLACEMENT SECTIONS  


K118064

With the front fender apron assembly removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location
K108832

Brazing or Arc Brazing for Removal

a.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K117873C01
0,0 0,0 false
K108837

Adhesive - -


K117874C01
3.573,0.406 3.885,0.563 0.313,0.156 10 false *a
*a 45 mm (1.77 in.) - -


K117875

K117876C01
0.167,0.083 7,3.667 6.833,3.583 3.583,3.667 3.583,0.083 false 0.333,0.25 0.646,0.406 0.313,0.156 10 false *A 3.75,0.25 4.063,0.406 0.313,0.156 10 false *B
*A for Type A *B for Type B




INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108825

Plug Weld
K108827

Cut and Join Location
K108830

Fillet Weld
K108831

Butt Weld
K108832

Braze
K108834

Body Sealer

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

If the entire supply part is not needed, remove the part of the supply part that is needed.

K117877C01
2.417,2.917 2.25,2.917 2.25,2.917 2.698,1.979 false 2.448,2.854 2.76,3.01 0.313,0.156 10 false *1 3.083,1.292 3.396,1.448 0.313,0.156 10 false *a
*1 ROCKER PANEL OUTER - -
*a 45 mm (1.77 in.) - -



d.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K117878


e.

Before temporarily installing the new parts, weld the rocker panel outer, front body pillar sub-assembly outer, front body pillar end plate and cowl side panel sub-assembly with the standard number of welding points.

K117879C01
5.833,0.917 6.333,0.333 6.333,0.333 6.5,0.333 false 1.333,0.25 1.5,0.25 1.5,0.25 1.667,0.594 false 4.333,3.667 4.167,3.667 4.167,3.667 4.438,3.167 false 2.583,3.5 2.417,3.5 2.417,3.5 2.167,3.156 false 2.615,3.438 2.927,3.594 0.313,0.156 10 false *1 1.167,0.188 1.479,0.344 0.313,0.156 10 false *2 6.531,0.271 6.844,0.427 0.313,0.156 10 false *3 4.365,3.604 4.677,3.76 0.313,0.156 10 false *4
*1 ROCKER PANEL OUTER *2 FRONT BODY PILLAR SUB-ASSEMBLY OUTER
*3 FRONT BODY PILLAR END PLATE *4 COWL SIDE PANEL SUB-ASSEMBLY



f.

Before temporarily installing the new parts, weld the front body pillar upper inner and front body pillar reinforcement upper inner with the standard number of welding points.

K117880C01
3.302,0.698 2.917,0.333 2.917,0.333 2.75,0.333 false 3.792,1 4.25,0.5 4.25,0.5 4.417,0.5 false 4.438,0.427 4.75,0.583 0.313,0.156 10 false *1 2.583,0.26 2.896,0.417 0.313,0.156 10 false *2 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A for Type A - -
*1 FRONT BODY PILLAR UPPER INNER *2 FRONT BODY PILLAR REINFORCEMENT UPPER INNER



g.

Before temporarily installing the new parts, weld the front body pillar upper inner, front body pillar reinforcement upper inner and identification number plate bracket with the standard number of welding points.

K118695C01
3.792,1 4.25,0.5 4.25,0.5 4.417,0.5 false 2.75,0.333 2.917,0.333 2.917,0.333 3.292,0.688 false 2.833,1.5 3,1.5 3,1.5 3.375,1.073 false 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 4.448,0.427 4.76,0.583 0.313,0.156 10 false *1 2.583,0.26 2.896,0.417 0.313,0.156 10 false *2 2.667,1.427 2.979,1.583 0.313,0.156 10 false *3
*A for Type B - -
*1 FRONT BODY PILLAR UPPER INNER *2 FRONT BODY PILLAR REINFORCEMENT UPPER INNER
*3 IDENTIFICATION NUMBER PLATE BRACKET - -



h.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K117882


i.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



K117883C01
0,0 0,0 false
K108837

Adhesive - -


K117884

K117885

K117886C01
0.167,0.083 7,3.667 6.833,3.583 3.583,3.667 3.583,0.083 false 0.333,0.25 0.646,0.406 0.313,0.156 10 false *A 3.75,0.25 4.063,0.406 0.313,0.156 10 false *B 1.635,3.281 1.948,3.438 0.313,0.156 10 false *a
*A for Type A *B for Type B
*a 15 mm (0.59 in.) - -



j.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


k.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.