Home › Vehicle Exterior › BODY PANEL › QUARTER PANEL(for 2 Door Short Rug Roof Van)
BM25T0E _01 Vehicle Exterior _030570 BODY WELD POINT _0138776 QUARTER PANEL(for 2 Door Short Rug Roof Van) F

BODY WELD POINT  QUARTER PANEL(for 2 Door Short Rug Roof Van)  ASSEMBLY REPLACEMENT  


K118069

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108832

Brazing or Arc Brazing for Removal

K117945

K117946

K117927

K117947


INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108830

Fillet Weld
K108832

Braze
K108834

Body Sealer

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

Before temporarily installing the new parts, weld the quarter panel, rear door open switch set retainer and rear heater mounting retainer with the standard number of welding points.

K117948C01
1.583,2 1.75,2 1.75,2 2.052,1.75 false 4.25,3 4.083,3 4.083,3 4.333,2.094 false 3.75,1.24 4.083,0.833 4.083,0.833 4.25,0.833 false 5.75,1.24 6.083,0.833 6.083,0.833 6.25,0.833 false 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 4.281,2.927 4.594,3.083 0.313,0.156 10 false *1 1.417,1.927 1.729,2.083 0.313,0.156 10 false *2 4.281,0.76 4.594,0.917 0.313,0.156 10 false *3 6.281,0.74 6.521,0.927 0.24,0.188 10 false *3
*A LH - -
*1 QUARTER PANEL *2 REAR DOOR OPEN SWITCH SET RETAINER
*3 REAR HEATER MOUNTING RETAINER - -



d.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K117949C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A RH - -



e.

Before temporarily installing the new parts, weld the quarter panel, rear door open switch set retainer, rear heater mounting retainer and fuel inlet box with the standard number of welding points.

K117950C01
1.333,3.25 1.167,3.25 1.167,3.25 0.833,2.844 false 3.75,3.333 3.583,3.333 3.583,3.333 3.833,2.281 false 6.583,2.167 6.417,2.167 6.417,2.167 6.083,1.948 false 2.583,1.417 2.917,1 2.917,1 3.083,1 false 4.583,1.417 4.917,1 4.917,1 5.083,1 false 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 3.115,0.927 3.469,1.146 0.354,0.219 10 false *3 3.781,3.26 4.094,3.417 0.313,0.156 10 false *1 6.615,2.094 6.927,2.25 0.313,0.156 10 false *2 5.115,0.927 5.427,1.083 0.313,0.156 10 false *3 1.365,3.177 1.677,3.333 0.313,0.156 10 false *4
*A RH - -
*1 QUARTER PANEL *2 REAR DOOR OPEN SWITCH SET RETAINER
*3 REAR HEATER MOUNTING RETAINER *4 FUEL INLET BOX


K117934C01
4,1.333 4.333,1 4.333,1 4.5,1 false 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 4.531,0.938 4.844,1.094 0.313,0.156 10 false *1
*A RH - -
*1 FUEL FILLER OPENING LID SUB-ASSEMBLY - -



f.

Before installing a new part, apply body sealer.

HINT:
·

Apply body sealer evenly about 5 mm (0.20 in.) from the flange, avoiding any oozing.

·

Apply body sealer evenly, about 3 to 4 mm (0.12 to 0.16 in.) in diameter.



K117951C01
5.438,2.104 5.75,2.26 0.313,0.156 10 false *a
*a 5 mm (0.20 in.) - -



g.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K117952

K117953

K117954

K117938

K117955C01
0.802,0.958 1.115,1.115 0.313,0.156 10 false *a 0.677,1.521 0.99,1.677 0.313,0.156 10 false *b
*a 15 mm (0.59 in.) *b 10 mm (0.39 in.)



h.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


i.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.