Home › Vehicle Exterior › BODY PANEL › QUARTER PANEL (for 2 Door Short Steel Roof Van) › 2014.08–2021.01
BM25T0E _01 Vehicle Exterior _030570 BODY WELD POINT _0138775 QUARTER PANEL(for 2 Door Short Steel Roof Van) F

BODY WELD POINT  QUARTER PANEL(for 2 Door Short Steel Roof Van)  CUT AND JOIN REPLACEMENT SECTIONS  


K118067

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108827

Cut and Join Location

K117925

K117926C01
0.948,1.042 1.26,1.198 0.313,0.156 10 false *a 4.656,1.063 4.948,1.313 0.292,0.25 10 false *a
*a 200 mm (7.87 in.) - -


K117927

K117928


INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108827

Cut and Join Location
K108831

Butt Weld
K108834

Body Sealer

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

If the entire supply part is not needed, remove the part of the supply part that is needed.

K117929C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 4.25,0.698 4.563,0.854 0.313,0.156 10 false *a 3.083,0.698 3.417,0.979 0.333,0.281 10 false *a
*A LH - -
*a 200 mm (7.87 in.) - -



d.

Before temporarily installing the new parts, weld the quarter panel and rear door open switch set retainer with the standard number of welding points.

K117930C01
1.583,2.167 1.75,2.167 1.75,2.167 2.083,1.917 false 4.313,3.167 4.146,3.167 4.146,3.167 4.417,2.313 false 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 4.365,3.094 4.677,3.25 0.313,0.156 10 false *1 1.417,2.094 1.729,2.25 0.313,0.156 10 false *2
*A LH - -
*1 QUARTER PANEL *2 REAR DOOR OPEN SWITCH SET RETAINER



e.

If the entire supply part is not needed, remove the part of the supply part that is needed.

K117931C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 4,0.698 4.313,0.854 0.313,0.156 10 false *a 2.833,0.698 3.25,1.063 0.417,0.365 10 false *a
*A RH - -
*a 200 mm (7.87 in.) - -



f.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K117932C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A RH - -



g.

Before temporarily installing the new parts, weld the quarter panel, rear door open switch set retainer and fuel inlet box with the standard number of welding points.

K117933C01
1.333,3.25 1.167,3.25 1.167,3.25 0.833,2.844 false 3.833,3.417 3.667,3.417 3.667,3.417 4,2.333 false 6.583,2.167 6.417,2.167 6.417,2.167 6.073,1.948 false 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 3.865,3.344 4.177,3.5 0.313,0.156 10 false *1 6.615,2.094 6.927,2.25 0.313,0.156 10 false *2 1.365,3.177 1.677,3.333 0.313,0.156 10 false *3
*A RH - -
*1 QUARTER PANEL *2 REAR DOOR OPEN SWITCH SET RETAINER
*3 FUEL INLET BOX - -


K117934C01
4,1.333 4.333,1 4.333,1 4.5,1 false 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 4.531,0.938 4.844,1.094 0.313,0.156 10 false *1
*A RH - -
*1 FUEL FILLER OPENING LID SUB-ASSEMBLY - -



h.

Before installing a new part, apply body sealer.

HINT:
·

Apply body sealer evenly about 5 mm (0.20 in.) from the flange, avoiding any oozing.

·

Apply body sealer evenly, about 3 to 4 mm (0.12 to 0.16 in.) in diameter.



K117935C01
5.458,2.125 5.771,2.281 0.313,0.156 10 false *a
*a 5 mm (0.20 in.) - -



i.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K117936

K117937

K117938

K117939


j.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


k.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.