Home › Vehicle Exterior › BODY PANEL › REAR FLOOR PAN(for 2 Door Short Van)
BM25T0E _01 Vehicle Exterior _030570 BODY WELD POINT _0139899 REAR FLOOR PAN(for 2 Door Short Van) F

BODY WELD POINT  REAR FLOOR PAN(for 2 Door Short Van)  CUT AND JOIN REPLACEMENT SECTIONS  


K118081

With the body lower back inner panel cut and join replacement sections (small areas) removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108829

Cut Location

K118336C01
1.969,1.656 2.281,1.813 0.313,0.156 10 false *a
*a 470 mm (18.50 in.) - -


K118337C01
0.25,0.333 6.917,3.5 6.667,3.167 3.583,3.5 3.583,0.333 false 0.417,0.417 0.729,0.573 0.313,0.156 10 false *A 3.75,0.427 4.063,0.583 0.313,0.156 10 false *B
*A LH Side *B RH Side


K118338C01
0.25,0.177 0.563,0.333 0.313,0.156 10 false *A
*A LH Side - -


K118339C01
0.25,0.167 0.563,0.323 0.313,0.156 10 false *A
*A RH Side - -



INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108825

Plug Weld
K108829

Cut Location
K108834

Body Sealer

a.

Cut the new part so that it overlaps the previous cut location by approximately 30 mm (1.18 in.).

K118340C01
0.25,0.167 0.563,0.323 0.313,0.156 10 false *A 1.542,1.833 1.854,1.99 0.313,0.156 10 false *a
*A Upper Face - -
*a 440 mm (17.32 in.) - -



b.

Before temporarily installing the new parts, weld the rear floor pan, rear floor pan reinforcement and jack carrier reinforcement with the standard number of welding points.

K118341C01
0.833,0.583 6.333,3.25 5.5,2.667 3.417,1.323 3.583,0.823 3.583,0.823 3.75,0.823 false 5.281,1.948 5.604,1.531 5.604,1.531 5.771,1.531 false 1.74,1.042 1.906,1.042 1.906,1.042 2.25,1.604 false 0.25,0.167 0.563,0.323 0.313,0.156 10 false *A 1,0.75 1.313,0.906 0.313,0.156 10 false *B 3.792,0.74 4.104,0.896 0.313,0.156 10 false *1 1.573,0.958 1.885,1.115 0.313,0.156 10 false *2 5.813,1.448 6.125,1.604 0.313,0.156 10 false *3
*A Lower Face *B except Face to Face Seat Type with Seat Belt
*1 REAR FLOOR PAN *2 REAR FLOOR PAN REINFORCEMENT
*3 JACK CARRIER REINFORCEMENT - -



c.

Before temporarily installing the new parts, weld the rear floor pan, rear floor pan reinforcement, jack carrier reinforcement, belt anchor reinforcement No.1 and seat belt anchor reinforcement No.2 with the standard number of welding points.

K118342C01
0.833,0.583 6.333,3.25 5.5,2.667 3.5,1.323 3.417,0.823 3.417,0.823 3.583,0.823 false 5.281,1.958 5.583,1.417 5.583,1.417 5.75,1.417 false 4.417,2.667 4.583,2.667 4.583,2.667 4.927,2.135 false 1.583,2.667 1.75,2.667 1.75,2.667 2.146,2.146 false 2.25,1.604 2,1.083 2,1.083 1.833,1.083 false 0.25,0.167 0.563,0.323 0.313,0.156 10 false *A 1,0.75 1.313,0.906 0.313,0.156 10 false *B 3.625,0.74 3.938,0.896 0.313,0.156 10 false *1 1.677,1 1.99,1.156 0.313,0.156 10 false *2 5.781,1.333 6.094,1.49 0.313,0.156 10 false *3 1.417,2.583 1.667,2.75 0.25,0.167 10 false *4 4.26,2.583 4.573,2.74 0.313,0.156 10 false *5
*A Lower Face *B for Face to Face Seat Type with Seat Belt
*1 REAR FLOOR PAN *2 REAR FLOOR PAN REINFORCEMENT
*3 JACK CARRIER REINFORCEMENT *4 BELT ANCHOR REINFORCEMENT NO.1
*5 SEAT BELT ANCHOR REINFORCEMENT NO.2 - -



d.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K118343


e.

Perform plug-welding in the area where the panel are overlapped. Apply body sealer to both sides of each panel.

HINT:
·

Confirm that the panels are securely welded together.

·

Apply body sealer in an even, continuous bead.



K118344

K118345C01
0.25,0.333 6.917,3.5 6.667,3.167 3.583,3.5 3.583,0.333 false 0.417,0.5 0.729,0.656 0.313,0.156 10 false *A 3.75,0.5 4.063,0.656 0.313,0.156 10 false *B
*A LH Side *B RH Side


K118346C01
0.25,0.167 0.563,0.323 0.313,0.156 10 false *A
*A LH Side - -


K118347C01
0.25,0.167 0.563,0.323 0.313,0.156 10 false *A
*A RH Side - -



f.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting/coating)


g.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.