Home › Vehicle Exterior › BODY PANEL › BODY LOWER BACK OUTER PANEL(for 2 Door Short Van)
BM25T0E _01 Vehicle Exterior _030570 BODY WELD POINT _0139879 BODY LOWER BACK OUTER PANEL(for 2 Door Short Van) F

BODY WELD POINT  BODY LOWER BACK OUTER PANEL(for 2 Door Short Van)  CUT AND JOIN REPLACEMENT SECTIONS (LARGE AREAS)  


K118078

With the back door opening trough assembly or back door opening trough cut and join replacement sections removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location

a.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K118233C01
0.25,0.167 0.563,0.323 0.313,0.156 10 false *A 4.99,2.24 5.302,2.396 0.313,0.156 10 false *a
*A LH Side - -
*a 120 mm (4.72 in.) - -
K108837

Adhesive - -


K118234C01
0.25,0.167 0.563,0.365 0.313,0.198 10 false *A
*A LH Side - -
K108837

Adhesive - -


K118235C01
0.25,0.177 0.563,0.333 0.313,0.156 10 false *A
*A LH Side - -



b.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K118236C01
0.25,0.167 0.563,0.323 0.313,0.156 10 false *A 2,2.25 2.313,2.406 0.313,0.156 10 false *a
*A RH Side - -
*a 120 mm (4.72 in.) - -
K108837

Adhesive - -


K118237C01
0.271,0.167 0.583,0.365 0.313,0.198 10 false *A
*A RH Side - -
K108837

Adhesive - -


K118238C01
0.25,0.167 0.563,0.323 0.313,0.156 10 false *A
*A RH Side - -




INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld
K108830

Fillet Weld
K108831

Butt Weld

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



K118239C01
0.25,0.177 0.563,0.333 0.313,0.156 10 false *A
*A LH Side - -
K108837

Adhesive - -


K118240C01
3.5,2.031 3.25,1.25 3.25,1.25 3.417,1.25 false 0.25,0.167 0.563,0.323 0.313,0.156 10 false *A 3.479,1.167 3.792,1.323 0.313,0.156 10 false *1
*A LH Side - -
*1 BODY LOWER BACK PANEL SUB-ASSEMBLY - -


K118241C01
0.25,0.167 0.563,0.323 0.313,0.156 10 false *A
*A LH Side - -


K118242C01
0.25,0.167 0.563,0.323 0.313,0.156 10 false *A
*A LH Side - -



d.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



K118243C01
0.25,0.167 0.563,0.323 0.313,0.156 10 false *A
*A RH Side - -
K108837

Adhesive - -


K118244C01
3.667,2.031 3.417,1.333 3.417,1.333 3.583,1.333 false 0.25,0.167 0.563,0.323 0.313,0.156 10 false *A 3.625,1.25 3.938,1.406 0.313,0.156 10 false *1
*A RH Side - -
*1 BODY LOWER BACK PANEL SUB-ASSEMBLY - -


K118245C01
0.25,0.177 0.563,0.333 0.313,0.156 10 false *A
*A RH Side - -


K118246C01
0.25,0.167 0.563,0.323 0.313,0.156 10 false *A 2.833,1.344 3.146,1.5 0.313,0.156 10 false *a
*A RH Side - -
*a 20 mm (0.79 in.) - -



e.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


f.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.