Home › Vehicle Exterior › BODY PANEL › QUARTER PANEL (for 2 Door Long Steel Roof Van) › from 2021.01
BM25T0E _01 Vehicle Exterior _030570 BODY PANEL _0138536 QUARTER PANEL(for 2 Door Long Steel Roof Van) F

BODY PANEL  QUARTER PANEL(for 2 Door Long Steel Roof Van)  CUT AND JOIN REPLACEMENT SECTIONS  


K109018

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108827

Cut and Join Location

K118131

K118132C01
0.656,1.51 0.969,1.667 0.313,0.156 10 false *a 5.281,1.271 5.594,1.427 0.313,0.156 10 false *b 3.052,0.552 3.365,0.708 0.313,0.156 10 false *a
*a 200 mm (7.87 in.) *b 160 mm (6.30 in.)


K118133C01
0.417,0.667 6.75,3.167 6.333,2.5 3.667,3.167 3.667,0.667 false 0.583,0.76 0.896,0.917 0.313,0.156 10 false *A 3.833,0.76 4.146,0.917 0.313,0.156 10 false *B
*A w/ Seat Belt *B w/o Seat Belt


a.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K118134C01
0,0 0,0 false
K108837

Adhesive - -


K118135

K118136



INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108827

Cut and Join Location
K108831

Butt Weld
K108834

Body Sealer

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

If the entire supply part is not needed, remove the part of the supply part that is needed.

K118137C01
0.25,0.167 0.563,0.323 0.313,0.156 10 false *A 2.365,1.094 2.677,1.25 0.313,0.156 10 false *a 5.75,1.052 6.063,1.208 0.313,0.156 10 false *b 3.938,1.094 4.25,1.25 0.313,0.156 10 false *a
*A LH - -
*a 200 mm (7.87 in.) *b 160 mm (6.30 in.)



d.

Before temporarily installing the new parts, weld the quarter panel and rear door open switch set retainer with the standard number of welding points.

K118138C01
0.25,0.5 6.917,3.417 6.667,2.917 4.667,3 4.5,3 4.5,3 4.417,2.271 false 0.917,2.167 1.083,2.167 1.083,2.167 1.417,1.917 false 0.25,0.167 0.563,0.323 0.313,0.156 10 false *A 0.417,0.583 0.729,0.74 0.313,0.156 10 false *B 4.708,2.927 5.021,3.083 0.313,0.156 10 false *1 0.75,2.083 1.063,2.24 0.313,0.156 10 false *2
*A LH *B w/o Roof Rack
*1 QUARTER PANEL *2 REAR DOOR OPEN SWITCH SET RETAINER



e.

Before temporarily installing the new parts, weld the quarter panel, rear door open switch set retainer, quarter panel step retainer No.1 and quarter panel step retainer No.2 with the standard number of welding points.

K118139C01
0.25,0.417 6.917,5.5 6.667,5.083 1,1.917 1.167,1.917 1.167,1.917 1.417,1.615 false 4.75,2.667 4.583,2.667 4.583,2.667 4.417,1.958 false 6.333,3.833 6.167,3.833 6.167,3.833 5.833,3.5 false 6.333,4.708 6.167,4.708 6.167,4.708 5.833,4.375 false 0.25,0.167 0.563,0.323 0.313,0.156 10 false *A 0.354,0.5 0.667,0.656 0.313,0.156 10 false *B 4.813,2.594 5.125,2.75 0.313,0.156 10 false *1 0.833,1.844 1.146,2 0.313,0.156 10 false *2 6.375,4.635 6.688,4.792 0.313,0.156 10 false *3 6.375,3.76 6.688,3.917 0.313,0.156 10 false *4
*A LH *B w/ Roof Rack
*1 QUARTER PANEL *2 REAR DOOR OPEN SWITCH SET RETAINER
*3 QUARTER PANEL STEP RETAINER NO.1 *4 QUARTER PANEL STEP RETAINER NO.2



f.

If the entire supply part is not needed, remove the part of the supply part that is needed.

K118140C01
0.25,0.167 0.563,0.323 0.313,0.156 10 false *A 3.167,1.083 3.479,1.24 0.313,0.156 10 false *a 1.396,1.052 1.708,1.208 0.313,0.156 10 false *b 4.792,1.083 5.104,1.24 0.313,0.156 10 false *a
*A RH - -
*a 200 mm (7.87 in.) *b 160 mm (6.30 in.)



g.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K118141C01
0.25,0.177 0.563,0.333 0.313,0.156 10 false *A
*A RH - -



h.

Before temporarily installing the new parts, weld the quarter panel, rear door open switch set retainer and fuel inlet box with the standard number of welding points.

K118142C01
2.333,2.333 2.5,2.333 2.5,2.333 2.75,1.708 false 0.917,3.917 1.083,3.917 1.083,3.917 1.354,3.656 false 6.333,1.667 6.167,1.667 6.167,1.667 5.833,1.365 false 3.333,3.917 3.5,3.917 3.5,3.917 3.771,3.656 false 0.25,0.177 0.563,0.333 0.313,0.156 10 false *A 2.177,2.26 2.49,2.417 0.313,0.156 10 false *1 6.365,1.583 6.677,1.74 0.313,0.156 10 false *2 0.76,3.833 1.073,3.99 0.313,0.156 10 false *3 3.177,3.844 3.49,4 0.313,0.156 10 false *3
*A RH - -
*1 QUARTER PANEL *2 REAR DOOR OPEN SWITCH SET RETAINER
*3 FUEL INLET BOX - -


K118143C01
2.333,1.219 2.667,0.583 2.667,0.583 2.833,0.583 false 5.906,1.281 6.25,0.667 6.25,0.667 6.417,0.667 false 0.25,0.167 0.563,0.323 0.313,0.156 10 false *A 2.885,0.5 3.198,0.656 0.313,0.156 10 false *1 6.479,0.573 6.792,0.729 0.313,0.156 10 false *1
*A RH - -
*1 FUEL FILLER OPENING LID SUB-ASSEMBLY - -



i.

Before installing a new part, apply body sealer.

HINT:
·

Apply body sealer evenly about 5 mm (0.20 in.) from the flange, avoiding any oozing.

·

Apply body sealer evenly, about 3 to 4 mm (0.12 to 0.16 in.) in diameter.



K118144C01
5.833,2.323 6.146,2.479 0.313,0.156 10 false *a
*a 5 mm (0.20 in.) - -



j.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K161468


k.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



K118146C01
0,0 0,0 false
K108837

Adhesive - -


K118147

K118148C01
0.417,0.75 6.75,3.167 6.333,2.417 3.667,3.167 3.667,0.75 false 0.583,0.844 0.896,1 0.313,0.156 10 false *A 3.833,0.844 4.146,1 0.313,0.156 10 false *B
*A w/ Seat Belt *B w/o Seat Belt


K118149

K118150

K118151


l.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


m.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.