FUNCTION OF MAIN COMPONENTS
| Component | Function | |
|---|---|---|
|
*1: Models with diesel engine *2: Models with differential lock system *3: Models with 1GR-FE or 1VD-FTV engine |
||
| Brake Actuator Assembly | Solenoid Valves | Change the fluid path based on the signals from the skid control ECU during the operation of the ABS in order to control the fluid pressure applied to the wheel cylinders. |
| Pump Motor | Drives the pumps inside the brake actuator. | |
| Solenoid Relay (Built into Skid Control ECU) | Supplies power to the solenoid valves. | |
| Motor Relay (Built into Skid Control ECU) | Supplies power to the pump motor. | |
| Skid Control ECU | Judges the vehicle driving condition based on the signals from each sensor and switch, and sends the brake control signals to the brake actuator. | |
| Speed Sensors | Detect the wheel speed of each of the 4 wheels. | |
| Deceleration Sensor | Detects the vehicle's longitudinal acceleration and deceleration. | |
| Stop Light Switch Assembly | Detects the brake pedal depression condition. | |
| Parking Brake Switch Assembly | Detects the parking brake lever status. | |
| Brake Fluid Level Warning Switch | Detects the brake fluid level. | |
| Vacuum Warning Switch Assembly*1 | Detects the negative pressure inside the vacuum reservoir assembly. | |
| L4 Detection Switch (No. 1 Transfer Indicator Switch) | Detects the L4 position condition. | |
| 4WD Detection Switch (No. 1 Transfer Indicator Switch) | Detects the 4WD position condition. | |
| Rear Differential Lock Position Switch (No. 4 Transfer Indicator Switch)*2 | Detects the rear differential lock actuator operating condition. | |
| Combination Meter Assembly | Brake System Warning Light |
·
Illuminates to alert the driver when the brake fluid level is low.
·
Illuminates to alert the driver when the vacuum drops inside the vacuum tank.*1 |
| ABS Warning Light |
·
Illuminates to alert the driver when the skid control ECU detects a malfunction in the ABS.
·
Illuminates to alert the driver when ABS function is not operating while the rear differential lock system is switching to lock.*2 |
|
| Buzzer | Emits a warning sound to alert the driver when the parking brake lever is pulled up. | |
| ECM*3 | Outputs the engine speed signal and accelerator pedal position signal to the skid control ECU via CAN communication. | |
| Component | Function | |
|---|---|---|
|
*: Models with differential lock system |
||
| Brake Actuator Assembly | Solenoid Relay (Built into Skid Control ECU) | Supplies power to the solenoid valves. |
| Motor Relay (Built into Skid Control ECU) | Supplies power to the pump motor. | |
| Motor Cut Relay (Built into Skid Control ECU) | Cuts the power to the pump motor when the motor relay malfunctions. | |
| Solenoid Valves | Change the fluid path based on signals from the skid control ECU during the operation of brake control system functions in order to control the fluid pressure applied to the wheel cylinders. | |
| Pump Motor | Drives the pumps inside the brake actuator. | |
| Master Cylinder Pressure Sensor | Detects the master cylinder pressure. | |
| Skid Control ECU | Determines the vehicle driving condition based on the signals from each ECU, sensor and switch, and sends brake control signals to the brake actuator. | |
| Speed Sensors | Detect the wheel speed of each of the 4 wheels. | |
| Airbag Sensor Assembly | Yawrate Sensor | Detects the vehicle's yaw rate. |
| Deceleration Sensor | Detects the vehicle's longitudinal and lateral acceleration. | |
| Steering Angle Sensor | Detects the steering direction and angle of the steering wheel. | |
| Stop Light Switch Assembly | Detects the brake pedal depression condition. | |
| Parking Brake Switch Assembly | Detects the parking brake lever status. | |
| Brake Fluid Level Warning Switch | Detects the brake fluid level. | |
| Vacuum Warning Switch Assembly | Detects the negative pressure inside the vacuum reservoir assembly. | |
| Back-up Light Switch Assembly | Detects the reverse position. | |
| VSC OFF Switch | Enables the driver to select "Normal Mode", "TRC OFF Mode" or "VSC OFF Mode". | |
| L4 Detection Switch (No. 1 Transfer Indicator Switch) | Detects the L4 position condition. | |
| 4WD Detection Switch (No. 1 Transfer Indicator Switch) | Detects the 4WD position condition. | |
| Rear Differential Lock Position Switch (No. 4 Transfer Indicator Switch)* | Detects the rear differential lock actuator operating condition. | |
| Combination Meter Assembly | Brake System Warning Light | Illuminates to alert the driver when the skid control ECU detects a malfunction in the EBD. |
| ABS Warning Light |
·
Illuminates to alert the driver when the skid control ECU detects a malfunction in the ABS.
·
Illuminates to inform the driver when LOCK mode is selected in the rear differential lock system.* |
|
| Slip Indicator Light |
·
Blinks to inform the driver when TRC, A-TRC or VSC is operational.
·
Illuminates to alert the driver when the skid control ECU detects a malfunction in the brake control function. |
|
| VSC OFF Indicator Light |
·
Illuminates to inform the driver when VSC OFF mode is selected.
·
Illuminates to inform the driver when LOCK mode is selected in the rear differential lock system.* |
|
| TRC OFF Indicator Light |
·
Illuminates to inform the driver when TRC OFF mode or VSC OFF mode is selected.
·
Illuminates to inform the driver when LOCK mode is selected in the rear differential lock system.* |
|
| Buzzer | Emits a warning sound to alert the driver when the parking brake lever is pulled up. | |
| ECM |
·
Outputs the engine speed signal and accelerator pedal position signal to the skid control ECU via CAN communication.
·
Controls the engine output based on signals form the skid control ECU. |
|
| Component | Function | |
|---|---|---|
| Brake Actuator Assembly | Skid Control ECU | Receives various signals and transmits an emergency brake signal to the combination meter assembly. |
| Airbag Sensor Assembly | Deceleration Sensor | Outputs the acceleration information. |
| Speed Sensors | Detect the wheel speed of each of the 4 wheels. | |
| Hazard Warning Signal Switch | Transmits a hazard warning signal switch on signal to the combination meter assembly. | |
| Stop Light Switch Assembly | Outputs the brake pedal operation signal. | |
| Combination Meter Assembly | Receives signals from the skid control ECU and hazard warning signal switch, and controls the each turn signal lights. | |
OPERATING CONDITION
Hill-start Assist Control
Hill-start assist control operates when all of the following conditions have been met:
|
·
The shift lever is in any position other than R (when forward climbing).
·
The shift lever is in R (when backward climbing).
·
The vehicle is at a standstill.
·
The accelerator pedal is not depressed.
·
The parking brake is not applied. |
If any one of the following conditions is met during hill-start assist control operation, hill-start assist control will be canceled.
|
·
The shift lever is moved to R (when forward climbing).
·
The shift lever is moved to a position other than R (when backward climbing).
·
The accelerator pedal is depressed.
·
The parking brake is applied.
·
Approximately 2 seconds elapse since the operation started. |
Emergency Brake Signal System
When all of the following conditions are met, the emergency brake signal starts operating:
|
·
Vehicle speed is above 55 km/h (35 mph).
·
Driver is depressing the brake pedal.
·
Emergency braking is detected from the vehicle deceleration.
·
The hazard warning signal switch is not pressed. |
When any of the following conditions is met, the emergency brake signal stops operating:
|
·
Driver has released the brake pedal.
·
Emergency braking is no longer detected from the vehicle deceleration.
·
The hazard warning signal switch is pressed. |
SYSTEM CONTROL
| Control | Outline |
|---|---|
| Anti-lock Brake System (ABS) | The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface. |
| Electronic Brake Force Distribution (EBD) | EBD control utilizes the ABS, achieving proper brake force distribution between the front and rear wheels in accordance with the driving conditions. In addition, during braking while cornering, it also controls the brake forces of the right and left wheels, helping maintain vehicle behavior. |
| Brake Assist | The primary purpose of brake assist is to provide an auxiliary brake force to assist a driver who cannot generate a large brake force during emergency braking, thus helping ensure the vehicle's braking performance. |
| Traction Control (TRC) | TRC helps restrain the slippage of the drive wheels if the driver depresses the accelerator pedal excessively when starting off or accelerating on a slippery surface. |
| Active Traction Control (A-TRC) | A-TRC controls the brake hydraulic pressure that is applied to the slipping wheel, and distributes the drive force that would have been lost through the slippage to the remaining wheels in order to achieve an LSD effect. |
| Vehicle Stability Control (VSC) | VSC helps restrain sideways slippage of the vehicle during a strong front wheel skid or a strong rear wheel skid, either of which may occur while cornering. |
| Hill-start Assist Control | When starting uphill, this control maintains the brake hydraulic pressure on all 4 wheels in order to momentarily prevent the vehicle from descending backward. |
| Emergency Brake Signal | In the case of emergency braking, the emergency brake signal flashes the turn signal lights to alert drivers in following vehicles. |
FAIL-SAFE
If a failure occurs in the skid control ECU, sensors or brake actuator assembly, the system continues performing brake control by excluding the failed area and using only the areas that are operating normally.
DIAGNOSIS
If the skid control ECU detects a malfunction in the brake control system, the warning lights or indicator light illuminate. At the same time, a Diagnostic Trouble Code (DTC) is stored in the memory of the skid control ECU.
This system has a sensor signal check (test mode) function.
For details of DTCs and check function, refer to the Repair Manual.