CONSTRUCTION
Models without VSC
A brake actuator with an integrated skid control ECU is used.
A solenoid relay and motor relay are built into the skid control ECU.
| *1 | Skid Control ECU
·
Solenoid Relay
·
Motor Relay |
*2 | Actuator Portion |
The brake actuator assembly consists of 6 two-position solenoid valves, 1 motor, 2 pumps and 2 reservoirs. The 6 two-position solenoid valves consist of 3 pressure holding valves and 3 pressure reduction valves.
| *1 | Brake Master Cylinder Sub-assembly | *2 | Brake Actuator Assembly |
| *3 | Pressure Holding Valve | *4 | Pump |
| *5 | Pressure Reduction Valve | *6 | Reservoir |
| *7 | Load Sensing Proportioning Valve Assembly | *8 | Front Left Brake |
| *9 | Front Right Brake | *10 | Rear Left Brake |
| *11 | Rear Right Brake | - | - |
Models with VSC
A brake actuator with an integrated skid control ECU is used.
A solenoid relay, motor relay and motor cut relay are built into the skid control ECU.
| *1 | Skid Control ECU
·
Solenoid Relay
·
Motor Relay
·
Motor Cut Relay |
*2 | Actuator Portion |
The actuator portion consists of 2 master cylinder cut solenoid valves, 4 pressure holding solenoid valves, 4 pressure reduction solenoid valves, 2 pumps, 2 reservoirs and a master cylinder pressure sensor.
| *1 | Master Cylinder Pressure Sensor | *2 | Master Cylinder Cut Solenoid Valve |
| *3 | Pressure Holding Solenoid Valve | *4 | Pressure Reduction Solenoid Valve |
| *5 | Pump | *6 | Reservoir |
| *a | From Master Cylinder | *b | Rear Brake LH |
| *c | Rear Brake RH | *d | Front Brake LH |
| *e | Front Brake RH | - | - |
OPERATION
ABS and EBD
Based on the signals received from the 4 speed sensors, the skid control ECU calculates the speed of each wheel and deceleration, and checks the wheel slipping condition. In accordance with to the slipping condition, the skid control ECU controls the pressure holding valve and pressure reduction valve in order to adjust the fluid pressure of each wheel cylinder in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes.
| *1 | Pressure Holding Solenoid Valve | *2 | Pressure Reduction Solenoid Valve |
| *3 | Port A | *4 | Port B |
| *a | Pressure Increase Mode | *b | Pressure Holding Mode |
| *c | Pressure Reduction Mode | *d | To Wheel Cylinder |
| *e | From Wheel Cylinder | - | - |
| Pressure Mode | Increase Mode | Holding Mode | Reduction Mode |
|---|---|---|---|
| Pressure Holding Solenoid Valve (Port A) | Off (Open) | On (Closed) | ← |
| Pressure Reduction Solenoid Valve (Port B) | Off (Closed) | ← | On (Open) |
| Wheel Cylinder Pressure | Increases | Holds | Reduces |
Brake Assist
In the event of emergency braking, the skid control ECU determines the driver's intention based on the speed of the pressure increase in the master cylinder determined by the master cylinder pressure sensor signal. If the skid control ECU determines the need for additional brake assist, pressure is generated by the pump in the brake actuator assembly and directed to the wheel cylinder to apply a large amount of fluid pressure.
| *1 | Master Cylinder Pressure Sensor | *2 | Master Cylinder Cut Solenoid Valve |
| *3 | Pressure Holding Solenoid Valve | *4 | Pressure Reduction Solenoid Valve |
| *5 | Pump | *6 | Reservoir |
| *a | From Master Cylinder | *b | Rear Brake LH |
| *c | Rear Brake RH | *d | Front Brake LH |
| *e | Front Brake RH | - | - |
| Item | Brake Assist not Activated | Brake Assist Activated | |
| Pump | Off | On | |
| Master Cylinder Cut Solenoid Valve | Port (A) | Off (Open) | On* |
| Port (B) | Off (Open) | On* | |
| Pressure Holding Solenoid Valve | Port (C) | Off (Open) | ← |
| Port (D) | Off (Open) | ← | |
| Port (E) | Off (Open) | ← | |
| Port (F) | Off (Open) | ← | |
| Pressure Reduction Solenoid Valve | Port (G) | Off (Closed) | ← |
| Port (H) | Off (Closed) | ← | |
| Port (I) | Off (Closed) | ← | |
| Port (J) | Off (Closed) | ← | |
*: The solenoid valve switches the hydraulic pressure between "open" and "closed" in accordance with the operating conditions by adjusting continually.
TRC
The fluid pressure generated by the pump is regulated by the master cylinder cut solenoid valve to the required pressure. Thus, the wheel cylinders of the drive wheels are controlled in the pressure increase, pressure holding and pressure reduction modes to control the slippage of the drive wheels. The pressure holding solenoid valve and the pressure reduction solenoid valve are turned on or off in accordance with ABS and EBD operation patterns.
| *1 | Master Cylinder Pressure Sensor | *2 | Master Cylinder Cut Solenoid Valve |
| *3 | Pressure Holding Solenoid Valve | *4 | Pressure Reduction Solenoid Valve |
| *5 | Pump | *6 | Reservoir |
| *a | From Master Cylinder | *b | Rear Brake LH |
| *c | Rear Brake RH | *d | Front Brake LH |
| *e | Front Brake RH | - | - |
| Item | TRC Operation | |||||
| Not Activated | Pressure Increase Mode | Pressure Holding Mode | Pressure Reduction Mode | |||
| Pump | Off | On | ← | ← | ||
| Master Cylinder Cut Solenoid Valve | Port (A) | Off (Open) | On*2 | ← | ← | |
| Port (B) | Off (Open) | ← | ← | ← | ||
| Front Brake | Pressure Holding Solenoid Valve | Port (E) | Off (Open) | On (Closed) | ← | ← |
| Port (F) | Off (Open) | On (Closed) | ← | ← | ||
| Pressure Reduction Solenoid Valve | Port (I) | Off (Closed) | ← | ← | ← | |
| Port (J) | Off (Closed) | ← | ← | ← | ||
| Wheel Cylinder Pressure | Left | - | - | - | - | |
| Right | - | - | - | - | ||
| Rear Brake | Pressure Holding Solenoid Valve | Port (C) | Off (Open) | ← | On (Closed) | ← |
| Port (D) | Off (Open) | ← | On (Closed) | ← | ||
| Pressure Reduction Solenoid Valve | Port (G) | Off (Closed) | ← | ← | On (Open) | |
| Port (H) | Off (Closed) | ← | ← | On (Open) | ||
| Wheel Cylinder Pressure | Left | - | Increases | Holds | Reduces | |
| Right | - | Increases | Holds | Reduces | ||
*1: This table shows the brake control operation when the drive mode is in H2.
*2: The solenoid valve switches the hydraulic pressure between "open" and "closed" in accordance with the operating conditions by adjusting continually.
A-TRC
Based on the vehicle speed that has been calculated from each speed sensor and the signals of the yawrate and deceleration sensor, the skid control ECU computes the target control speed.
The skid control ECU compares the target control speed and the wheel speed to determine whether or not slippage exists. Upon detecting slippage, the skid control ECU controls the solenoid valve of the brake actuator assembly to control the brake fluid pressure that is applied to the slipping wheel. When the wheel speed becomes lower than the target control speed, the skid control ECU stops increasing the brake fluid pressure.
The fluid pressure control of A-TRC independently controls the brake of each wheel by operating the individual solenoid valves in accordance with the signals received from the skid control ECU. The brake of each wheel is controlled in the following 3 modes: pressure increase, pressure holding, and pressure reduction modes.
| *1 | Master Cylinder Pressure Sensor | *2 | Master Cylinder Cut Solenoid Valve |
| *3 | Pressure Holding Solenoid Valve | *4 | Pressure Reduction Solenoid Valve |
| *5 | Pump | *6 | Reservoir |
| *a | From Master Cylinder | *b | Rear Brake LH |
| *c | Rear Brake RH | *d | Front Brake LH |
| *e | Front Brake RH | - | - |
| Item | A-TRC Operation | |||||
| Not Activated | Pressure Increase Mode | Pressure Holding Mode | Pressure Reduction Mode | |||
| Pump | Off | On | ← | ← | ||
| Master Cylinder Cut Solenoid Valve | Port (A) | Off (Open) | On* | ← | ← | |
| Port (B) | Off (Open) | On* | ← | ← | ||
| Front Brake | Pressure Holding Solenoid Valve | Port (E) | Off (Open) | ← | On (Closed) | ← |
| Port (F) | Off (Open) | ← | On (Closed) | ← | ||
| Pressure Reduction Solenoid Valve | Port (I) | Off (Closed) | ← | ← | On (Open) | |
| Port (J) | Off (Closed) | ← | ← | On (Open) | ||
| Wheel Cylinder Pressure | Left | - | Increases | Holds | Reduces | |
| Right | - | Increases | Holds | Reduces | ||
| Rear Brake | Pressure Holding Solenoid Valve | Port (C) | Off (Open) | ← | On (Closed) | ← |
| Port (D) | Off (Open) | ← | On (Closed) | ← | ||
| Pressure Reduction Solenoid Valve | Port (G) | Off (Closed) | ← | ← | On (Open) | |
| Port (H) | Off (Closed) | ← | ← | On (Open) | ||
| Wheel Cylinder Pressure | Left | - | Increases | Holds | Reduces | |
| Right | - | Increases | Holds | Reduces | ||
*: The solenoid valve switches the hydraulic pressure between "open" and "closed" in accordance with the operating conditions by adjusting continually.
VSC
VSC, by way of the solenoid valves, controls the fluid pressure generated by the pump and applies it to the brake wheel cylinder of each wheel in the following 3 modes: pressure increase, pressure holding and pressure reduction modes. As a result, the tendency for front wheel skid or rear wheel skid is controlled.
In front wheel skid restraint control, the brakes of the front wheel on the outer circle of the turn and the rear wheels are applied. Also, depending on whether the brake is on or off and also depending on the vehicle condition, there are circumstances in which the brake might not be applied to the wheels even if the wheel is targeted for braking. The following diagram shows the hydraulic circuit in the pressure increase mode, as it controls the front wheel skid condition while the vehicle is making a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned on or off in accordance with ABS and EBD operation patterns.
| *1 | Master Cylinder Pressure Sensor | *2 | Master Cylinder Cut Solenoid Valve |
| *3 | Pressure Holding Solenoid Valve | *4 | Pressure Reduction Solenoid Valve |
| *5 | Pump | *6 | Reservoir |
| *a | From Master Cylinder | *b | Rear Brake LH |
| *c | Rear Brake RH | *d | Front Brake LH |
| *e | Front Brake RH | - | - |
| Item | VSC Operation | |||||
| Not Activated | Pressure Increase Mode | Pressure Holding Mode | Pressure Reduction Mode | |||
| Pump | Off | On | ← | ← | ||
| Master Cylinder Cut Solenoid Valve | Port (A) | Off (Open) | On* | ← | ← | |
| Port (B) | Off (Open) | On* | ← | ← | ||
| Front Brake | Pressure Holding Solenoid Valve | Port (E) | Off (Open) | ← | On (Closed) | ← |
| Port (F) | Off (Open) | On (Closed) | ← | ← | ||
| Pressure Reduction Solenoid Valve | Port (I) | Off (Closed) | ← | ← | On (Open) | |
| Port (J) | Off (Closed) | ← | ← | ← | ||
| Wheel Cylinder Pressure | Left | - | Increases | Holds | Reduces | |
| Right | - | - | - | - | ||
| Rear Brake | Pressure Holding Solenoid Valve | Port (C) | Off (Open) | ← | On (Closed) | ← |
| Port (D) | Off (Open) | ← | On (Closed) | ← | ||
| Pressure Reduction Solenoid Valve | Port (G) | Off (Closed) | ← | ← | On (Open) | |
| Port (H) | Off (Closed) | ← | ← | On (Open) | ||
| Wheel Cylinder Pressure | Left | - | Increases | Holds | Reduces | |
| Right | - | Increases | Holds | Reduces | ||
*: The solenoid valve switches the hydraulic pressure between "open" and "closed" in accordance with the operating conditions by adjusting continually.
In rear wheel skid restraint control, the brakes of the front wheel on the outer circle of the turn are applied. Also, depending on whether the brake is on or off and also depending on the vehicle condition, there are circumstances in which the brake might not be applied to the wheels even if the wheel is targeted for braking. The following diagram shows the hydraulic circuit in pressure increase mode, as it controls the rear wheel skid condition while the vehicle is making a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned on or off in accordance with ABS and EBD operation patterns.
| *1 | Master Cylinder Pressure Sensor | *2 | Master Cylinder Cut Solenoid Valve |
| *3 | Pressure Holding Solenoid Valve | *4 | Pressure Reduction Solenoid Valve |
| *5 | Pump | *6 | Reservoir |
| *a | From Master Cylinder | *b | Rear Brake LH |
| *c | Rear Brake RH | *d | Front Brake LH |
| *e | Front Brake RH | - | - |
| Item | VSC Operation | |||||
| Not Activated | Pressure Increase Mode | Pressure Holding Mode | Pressure Reduction Mode | |||
| Pump | Off | On | ← | ← | ||
| Master Cylinder Cut Solenoid Valve | Port (A) | Off (Open) | On* | ← | ← | |
| Port (B) | Off (Open) | On* | ← | ← | ||
| Front Brake | Pressure Holding Solenoid Valve | Port (E) | Off (Open) | ← | On (Closed) | ← |
| Port (F) | Off (Open) | On (Closed) | ← | ← | ||
| Pressure Reduction Solenoid Valve | Port (I) | Off (Closed) | ← | ← | On (Open) | |
| Port (J) | Off (Closed) | ← | ← | ← | ||
| Wheel Cylinder Pressure | Left | - | Increases | Holds | Reduces | |
| Right | - | - | - | - | ||
| Rear Brake | Pressure Holding Solenoid Valve | Port (C) | Off (Open) | On (Closed) | ← | ← |
| Port (D) | Off (Open) | On (Closed) | ← | ← | ||
| Pressure Reduction Solenoid Valve | Port (G) | Off (Closed) | ← | ← | ← | |
| Port (H) | Off (Closed) | ← | ← | ← | ||
| Wheel Cylinder Pressure | Left | - | - | - | - | |
| Right | - | - | - | - | ||
*: The solenoid valve switches the hydraulic pressure between "open" and "closed" in accordance with the operating conditions by adjusting continually.
Hill-start Assist Control
Hill-start assist control operation is performed by closing the master cylinder cut solenoid valves after the driver operates the brake pedal and leaving a certain amount of hydraulic pressure created by the pump in the wheel cylinder. The diagram below shows the hydraulic circuit in the pressure holding mode.
| *1 | Master Cylinder Pressure Sensor | *2 | Master Cylinder Cut Solenoid Valve |
| *3 | Pressure Holding Solenoid Valve | *4 | Pressure Reduction Solenoid Valve |
| *5 | Pump | *6 | Reservoir |
| *a | From Master Cylinder | *b | Rear Brake LH |
| *c | Rear Brake RH | *d | Front Brake LH |
| *e | Front Brake RH | - | - |
| Item | Hill-start Assist Control Operation | ||||
| Not Activated | Pressure Holding Mode | Pressure Reduction Mode | |||
| Master Cylinder Cut Solenoid Valve | Port (A) | Off (Open) | On* | ← | |
| Port (B) | Off (Open) | On* | ← | ||
| Front Brake | Pressure Holding Solenoid Valve | Port (E) | Off (Open) | ← | ← |
| Port (F) | Off (Open) | ← | ← | ||
| Pressure Reduction Solenoid Valve | Port (I) | Off (Closed) | ← | On (Open) | |
| Port (J) | Off (Closed) | ← | On (Open) | ||
| Wheel Cylinder Pressure | Left | - | Holds | Reduces | |
| Right | - | Holds | Reduces | ||
| Rear Brake | Pressure Holding Solenoid Valve | Port (C) | Off (Open) | ← | ← |
| Port (D) | Off (Open) | ← | ← | ||
| Pressure Reduction Solenoid Valve | Port (G) | Off (Closed) | ← | On (Open) | |
| Port (H) | Off (Closed) | ← | On (Open) | ||
| Wheel Cylinder Pressure | Left | - | Holds | Reduces | |
| Right | - | Holds | Reduces | ||
*: The solenoid valve switches the hydraulic pressure between "open" and "closed" in accordance with the operating conditions by adjusting continually.