Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BODY STRUCTURE › from 2016.08
NM25T0E _59 Vehicle Exterior _030650 EXTERIOR PANELS / TRIM _0138065 BODY STRUCTURE DE DETAILS F

EXTERIOR PANELS / TRIM  BODY STRUCTURE  DETAILS  LIGHTWEIGHT AND HIGHLY RIGID BODY  


CONSTRUCTION


a.

Upper Body

i.

The body has low vibration and noise due to the high rigidity provided by reinforcements positioned at the connections of each pillar.


ii.

Reinforcements are positioned in the side portion of the upper body at the connections of each pillar and the roof side rail. Also, reinforcements are positioned at the connections of each pillar and the rocker.


iii.

Reinforcements are provided in the floor at the connections of the dash panel and the floor, and the dash panel and each pillar.

Side Reinforcement
V106683C01
5.781,0.479 6.01,0.76 true 6.365,1.156 6.073,1.594 true 4.333,0.969 4.042,0.552 true 2.625,0.781 2.177,0.479 true 0.448,1.563 0.885,1.135 true 6.052,4.427 6.458,4.49 true 5.083,4.573 5.521,5.104 true 2.594,5.146 2.979,5.406 true 0.99,5.125 0.531,5.542 true 0.271,1.521 0.583,1.677 0.313,0.156 10 false *1 2.031,0.313 2.344,0.469 0.313,0.156 10 false *2 3.917,0.375 4.229,0.531 0.313,0.156 10 false *3 5.646,0.302 5.958,0.458 0.313,0.156 10 false *4 5.958,1.583 6.271,1.74 0.313,0.156 10 false *5 0.375,5.51 0.688,5.667 0.313,0.156 10 false *6 2.438,4.99 2.75,5.146 0.313,0.156 10 false *7 4.938,4.417 5.25,4.573 0.313,0.156 10 false *8 5.906,4.292 6.219,4.448 0.313,0.156 10 false *9 0.229,6.646 0.542,6.802 0.313,0.156 10 false *a
*1 Front Body Pillar Upper Inner Gusset *2 Center Body Pillar Upper Reinforcement
*3 Rear Pillar Inner Upper Reinforcement *4 Roof Side Inner Upper Extension
*5 Back Door Opening Upper Reinforcement *6 Front Body Pillar Lower Reinforcement
*7 Center Body Pillar Lower Reinforcement *8 Roof Side Quarter Panel
*9 Back Door Opening Reinforcement - -
*a The illustration shown is an example only. - -


Floor Reinforcement
V106684C01
2.885,1.844 2.563,0.313 true 2.115,1.635 1.25,0.521 true 1.948,2.417 0.656,2.188 true 1.198,3.177 2.198,2.573 true 1.771,3.833 2.583,2.646 true 2.563,4.135 2.885,3.104 true 3.302,4.458 3.406,3.365 true 4.427,2.604 4.042,4.302 4.042,4.302 3.625,3.094 true 5.594,3.177 5.823,4.292 5.823,4.292 4.688,3.635 true 4.76,3.135 6.458,2.594 true 4.802,2.594 5.938,1.292 true 4.344,2.365 5.219,0.656 true 4.125,2.75 4.01,0.365 4.01,0.365 3.719,2.74 true 1.104,0.354 1.417,0.51 0.313,0.156 10 false *1 0.5,2.073 0.813,2.229 0.313,0.156 10 false *2 1.052,3.104 1.365,3.26 0.313,0.156 10 false *3 1.604,3.823 1.917,3.979 0.313,0.156 10 false *4 2.479,4.125 2.792,4.281 0.313,0.156 10 false *5 3.219,4.458 3.531,4.615 0.313,0.156 10 false *6 4,4.302 4.313,4.458 0.313,0.156 10 false *7 5.823,4.281 6.135,4.438 0.313,0.156 10 false *8 6.5,2.469 6.813,2.625 0.313,0.156 10 false *9 0.208,4.583 0.521,4.74 0.313,0.156 10 false *a 3.927,0.177 4.24,0.333 0.313,0.156 10 false *9 2.479,0.125 2.792,0.281 0.313,0.156 10 false *2 5.177,0.469 5.49,0.625 0.313,0.156 10 false *5 5.927,1.104 6.24,1.26 0.313,0.156 10 false *6
*1 Dash Panel *2 Dash to Floor Reinforcement
*3 Front Floor Panel *4 Front Floor Panel Reinforcement
*5 Floor Side Inner Reinforcement *6 No. 2 Floor Side Member Reinforcement
*7 No. 4 Rear Floor Cross Member Reinforcement *8 Lower Back Panel Reinforcement
*9 Floor Cross Member - -
*a The illustration shown is an example only. - -




b.

Frame

i.

4 types of frames are used depending on the wheel base.

Short Wheel Base (The illustration shown is an example only.)
V106685

Semi-long Wheel Base (The illustration shown is an example only.)
V106686

Long Wheel Base (The illustration shown is an example only.)
V106687

Super Long Wheel Base (The illustration shown is an example only.)
V106688


ii.

On single cab models for Australia, a large side rail cross section is provided for the frame, and reinforced members with ultra high strength sheet steel (tensile strength: 980 MPa) are positioned effectively to ensure superior collision safety.


iii.

On single cab models for Australia, the steering gear box position of the frame is moved backwards to ensure the axial compression length of the front part of the side rail. As a result, sufficient energy absorption is performed in the front part of the rail until the frame begins to bend, ensuring a survival space in the cabin.


iv.

On single cab models for Australia, the cross member is added and the cross section of the side rail is optimized for the frame to control the frame bending mode during a collision, ensuring a survival space in the cabin.

V117843C01
1.083,2.5 0.833,2.083 0.833,2.083 0.667,2.083 true 2.333,2.917 2.833,3.667 2.833,3.667 3,3.667 true 4.698,3.417 4.917,3.667 false 5.417,3.417 5.167,3.667 false 4.698,4.25 4.917,4 false 5.417,4.25 5.167,4 false 6.75,3.333 6.583,3.833 true 6.75,4.583 6.583,4.083 true 0.521,2.01 0.833,2.167 0.313,0.156 10 false *1 3.031,3.583 3.344,3.74 0.313,0.156 10 false *2 1.927,1.813 2.24,1.969 0.313,0.156 10 false A 3.594,2.083 3.906,2.24 0.313,0.156 10 false B 5.031,4.573 5.344,4.729 0.313,0.156 10 false *a 6.458,4.656 6.771,4.813 0.313,0.156 10 false *b 5,2.844 5.313,3 0.313,0.156 10 false *c 4.969,3.771 5.281,3.927 0.313,0.156 10 false *d 6.417,2.844 6.729,3 0.313,0.156 10 false *c 4.25,3.75 4.563,3.906 0.313,0.156 10 false *c 5.75,3.844 6.063,4 0.313,0.156 10 false *c 6.438,3.844 6.75,4 0.313,0.156 10 false *d 2.479,2.51 2.792,2.667 0.313,0.156 10 false A 4.167,2.688 4.479,2.844 0.313,0.156 10 false B
*1 Steering Gear Box *2 Cross Member
*a A - A Cross Section *b B - B Cross Section
*c Widening *d High Strength Sheet Steel (Tensile Strength: 980 MPa)




c.

Deck

i.

A steel deck with a tailgate that can be opened is used for the single cab and double cab pick-up models.


ii.

A spare tire is positioned in the header board assembly of the deck depending on the specification.

Rear Deck (Single Cab Pick-up)
V106689

Rear Deck (Double Cab Pick-up)
V106690