FUNCTION OF MAIN COMPONENTS
The main components of the engine control system are as follows:
| Components | Outline | Quantity | Function |
|---|---|---|---|
|
*1: Except models compliant with EURO 5 emission regulations *2: Models compliant with EURO 5 emission regulations *3: Models compliant with EURO 4 emission regulations and models compliant with EURO 5 emission regulations *4: Models compliant with EURO 4 emission regulations |
|||
| ECM | FOREST*1 | 1 | The ECM effects overall control of the engine control system to suit the operating conditions of the engine in accordance with the signals provided by the sensors. |
| FOREST + 32-bit CPU*2 | |||
| Injector Driver | DC/DC Converter | 2 | The injector driver is used to drive the injector at high speeds. The injector driver has achieved high-speed driving under high fuel pressure conditions through the use of a DC/DC converter that provides a high voltage, quick-charging system. |
| Turbo Pressure Sensor | Semiconductor Silicon Chip Type | 1 | This sensor uses built-in semiconductors to detect the intake manifold pressure. |
| Atmospheric Pressure Sensor | Semiconductor Silicon Chip Type | 1 | This sensor, which is built into the ECM, uses semiconductors to detect the atmospheric pressure. |
| Fuel Pressure Sensor | Semiconductor Strain Gauge Type | 1 | This sensor uses built-in semiconductors to detect the internal pressure of the common-rail. |
| Crank Position Sensor | Pick-up Coil Type (Rotor Teeth /36-2) | 1 | This sensor detects the engine speed and performs the cylinder identification. |
| Cam Position Sensor | Pick-up Coil Type (Rotor Teeth /1) | 1 | This sensor performs the cylinder identification. |
| Intake Mass Air Flow Meter Sub-assembly | Analog, Hot-wire Type*1 | 1 | This sensor uses a built-in hot-wire to directly detect the intake air mass and flow rate. |
| Digital, Hot-wire Type*2 | |||
| Atmospheric Temperature Sensor | Thermistor Type | 1 |
·
This sensor, which is provided at the air cleaner outlet, detects the atmospheric temperature by means of an internal thermistor.
·
This sensor is built into the intake mass air flow meter sub-assembly. |
| Engine Coolant Temperature Sensor | Thermistor Type | 1 | This sensor detects the engine water temperature by means of an internal thermistor. |
| Intake Air Temperature Sensor | Thermistor Type | 1 | This sensor detects the intake air temperature after the intercooler. |
| Fuel Temperature Sensor | Thermistor Type | 1 | This sensor detects the fuel temperature in the supply pump by means of an internal thermistor. |
| Fuel Pressure Discharge Valve*2 | Solenoid Type | 1 | The fuel pressure discharge valve regulates the fuel pressure. |
| Throttle Position Sensor | Non-contact Type | 2 | This sensor detects the throttle valve opening angle. |
| Accelerator Pedal Sensor Assembly | Non-contact Type | 1 | This sensor detects the amount of pedal effort applied to the accelerator pedal. |
| EGR Valve Position Sensor*3 | Contact Type*4 | 2 | This sensor detects the actual amount of the EGR valve opening. For details, see the EMISSION CONTROL (1VD-FTV) section. |
| Non-contact Type*2 | 1 | ||
| Suction Control Valve (SCV) | Linear Solenoid Valve | 1 | The SCV position is controlled by the signals from the ECM, and a fuel volume that suits the SCV position is drawn into the pumping portion (plunger portion). For details, see the FUEL (1VD-FTV) section. |
| Injector Assembly | 9-hole, Solenoid Type*1 | 8 | The injector assembly contains a solenoid valve that opens and closes to increase or decrease the pressure in the control chamber. This causes the nozzle needle to open and close the valve, which results in fuel injection. For details, see the FUEL (1VD-FTV) section. |
| 9-hole, Piezo Type*2 | |||
| Exhaust Fuel Addition Injector Assembly*2 | Solenoid Type | 1 | The exhaust fuel addition injector assembly injects fuel into the fuel injection passage of the cylinder head sub-assembly. To reduce PM, the ECM controls the injection timing and frequency of the injector, and activates the exhaust fuel addition injector assembly. For details, see the FUEL (1VD-FTV) section. |
| Differential Pressure Sensor*2 | - | 1 | The differential pressure sensor monitors the differential pressure before and after the DPF to detect whether the DPF is clogged. For details, see the EMISSION CONTROL (1VD-FTV) section. |
| Exhaust Gas Temperature Sensor*2 | Thermistor Type | 3 | The exhaust gas temperature sensors are located before the oxidation catalyst, and before and after the DPF to detect the exhaust gas temperature. For details, see the EMISSION CONTROL (1VD-FTV) section. |
| Air Fuel Ratio Sensor*2 | - | 1 | The air fuel ratio sensor detects the oxygen concentration in exhaust gas. For details, see the EMISSION CONTROL (1VD-FTV) section. |
SYSTEM CONTROL
The engine control system has the following features. The ECM controls these systems:
| System | Outline | Emission Regulations | ||
|---|---|---|---|---|
| Non-compliant | EURO 4 | EURO 5 | ||
|
○: Applicable -: Not applicable *: Models with air conditioner system |
||||
| Fuel Injection Volume Control | Based on the signals received from the sensors, the ECM determines the fuel injection volume in accordance with the engine condition. | ○ | ○ | ○ |
| Fuel Injection Timing Control | Based on the signals received from the sensors, the ECM determines the fuel injection timing in accordance with the engine condition. | ○ | ○ | ○ |
| Fuel Pressure Control | Based on the signals received from the sensors, the ECM controls fuel pressure using the Suction Control Valve (SCV) according to the engine condition. | ○ | ○ | - |
| Based on the signals received from the sensors, the ECM controls fuel pressure using the Suction Control Valve (SCV) and fuel pressure discharge valve in accordance with engine operating conditions. | - | - | ○ | |
| Pilot Injection Control | Based on the signals received from the sensors, the ECM determines pilot injection volume/timing, and interval (between pilot injection and main injection) in accordance with the engine condition. | ○ | ○ | ○ |
| During Starting Control | To facilitate startability, the ECM optimally controls the fuel injection volume and timing during starting. | ○ | ○ | ○ |
| Idle Speed Control | The ECM determines the idle speed in accordance with the engine condition, and controls the fuel injection volume in order to maintain the target idle speed. | ○ | ○ | ○ |
| Glow Plug Control | The ECM controls the length of time when the electric current is applied to the glow plug assemblies, in accordance with the engine water temperature. | ○ | ○ | ○ |
| Diesel Throttle Control | Based on the signals received from the various sensors, the ECM determines the throttle valve position in accordance with the engine condition. | ○ | ○ | ○ |
| The throttle valve is fully closed in order to reduce the vibration when the engine is stopped. | ||||
| Turbocharger Control | Based on the signals received from the sensors, the ECM controls the actuator via the electric vacuum regulating valve in accordance with the engine condition. | ○ | ○ | ○ |
| EGR Control | Based on the signals received from the sensors, the ECM determines the EGR volume via the EGR valve and throttle valve in accordance with the engine condition. For details see the EMISSION CONTROL (1VD-FTV) section. |
- | ○ | ○ |
| Catalyst Support Control | Based on the signals received from the sensors, the ECM controls the exhaust fuel addition injector assembly to regenerate the DPF. For details see the EMISSION CONTROL (1VD-FTV) section. |
- | - | ○ |
| Air Fuel Ratio Sensor Heater Control | The ECM controls the temperature of the air fuel ratio sensors at an appropriate level to increase the detection accuracy of the exhaust gas oxygen concentration. | - | - | ○ |
| Air Conditioner Cut-off Control* | By controlling the air conditioner compressor on or off in accordance with the engine condition, driveability is maintained. | ○ | ○ | ○ |
| Brake Override System | The driving torque is restricted when the brake pedal is depressed while the accelerator pedal is depressed. (For the Activation Conditions and Inspection Method, refer to the Repair Manual.) | - | ○ | - |
| The driving torque is restricted when both the accelerator and brake pedals are depressed. (For the Activation Conditions and Inspection Method, refer to the repair manual.) | ○ | - | ○ | |
| Engine Immobiliser | The ECM prohibits fuel injection if the engine is tried to start with an invalid ignition key. | ○ | ○ | ○ |
| Diagnosis | When the ECM detects a malfunction, the ECM diagnoses and memorizes the failed section. | ○ | ○ | ○ |
| Fail-safe | When the ECM detects a malfunction, the ECM stops or controls the engine according to the data already stored in the memory. | ○ | ○ | ○ |