Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › ENGINE UNIT › from 2021.12
NM25T0E _51 Engine / Hybrid System _029292 1GR-FE ENGINE MECHANICAL _0137842 ENGINE UNIT GE GENERAL F

1GR-FE ENGINE MECHANICAL  ENGINE UNIT  GENERAL  GENERAL  


OUTLINE


a.

The 1GR-FE engine is a V-type, 6-cylinder, 4.0-liter, 24-valve DOHC engine.


b.

On this engine, the Variable Valve Timing-intelligent (VVT-i) system, Acoustic Control Induction System (ACIS), and the Electronic Throttle Control System-intelligent (ETCS-i) are used. These control functions have been optimized to further improve engine performance and fuel economy, and to reduce exhaust emissions.


c.

This engine has been made compact and lightweight through the use of an aluminum cylinder block and a plastic type intake air chamber, fuel delivery pipe, and water inlet pipe.



SPECIFICATION


No. of Cyls. and Arrangement 6-cylinder, V-type
Valve Mechanism 24-valve DOHC, Chain Drive (with VVT-i)
Combustion Chamber Pentroof Type
Manifolds Cross-flow
Fuel System Sequential Multiport Fuel Injection (SFI)
Ignition System Direct Ignition System (DIS)
Displacement 3956 cm3 (241.4 cu. in.)
Bore x Stroke 94.0 mm x 95.0 mm (3.70 in. x 3.74 in.)
Compression Ratio 10.0 : 1
Max. Output [SAE-NET] 170 kW @ 5200 rpm
Max. Torque [SAE-NET] 360 N*m @ 3800 rpm
Valve Timing Intake Open 42° to -8° BTDC
Closed 10° to 60° ABDC
Exhaust Open 54° BBDC
Closed 2° ATDC
Spark Plug Manufacturer DENSO NGK
Type K20HR-U11 LFR6C-11
Plug Gap 1.0 mm to 1.1 mm (0.0394 in. to 0.0433 in.)
Firing Order 1 - 2 - 3 - 4 - 5 - 6
Research Octane Number 95 or higher
Emission Regulation*1 EURO 2
EURO 4
EURO 5
Engine Service Mass (Reference)*2 180 kg (397 lb)

HINT:

*1: Emission regulations differ by country and region.

*2: Weight shows the figure with oil and coolant fully filled.



MAIN FEATURES


a.

This engine has been able to achieve the following performance features through the use of the items listed below:

i.

High performance and fuel economy


ii.

Low noise and vibration


iii.

Lightweight and compact design


iv.

Good serviceability


v.

Clean emissions

Item (1) (2) (3) (4) (5)
Engine Proper An upright intake port is used. ○ - ○ - -
A taper squish shape is used for the combustion chamber. ○ - - - ○
A steel-laminate type cylinder head gasket is used. ○ - - - -
Spiny-type liners are used in the cylinder bores. ○ - ○ - -
The piston skirt is coated with resin. ○ ○ - - ○
A No. 1 oil pan made of aluminum alloy is used. ○ ○ ○ - -
Valve Mechanism Timing chains and chain tensioners are used. ○ - ○ - -
Shim-less type valve lifters are used. ○ - ○ - -
The Variable Valve Timing-intelligent (VVT-i) system is used. ○ - - - ○
Lubrication System A water-cooled type oil cooler is used. ○ - - - -
Intake and Exhaust System An intake air surge tank made of plastic is used. - - ○ - -
A linkless-type throttle body is used. - - ○ ○ -
Three-Way Catalytic converters (TWCs) are used. - - - - ○
Fuel System 12-hole type fuel injector assemblies are used to improve the atomization of fuel. ○ - - - ○
Ignition System Long-reach type spark plugs are used. ○ - - - -
Serpentine Belt Drive System A serpentine belt drive system is used. - - ○ ○ -
Engine Control The Electronic Throttle Control System-intelligent (ETCS-i) is used. ○ - - - ○
The Direct Ignition System (DIS) makes ignition timing adjustment unnecessary. ○ - - ○ ○
The Acoustic Control Induction System (ACIS) is used. ○ - - - ○

HINT:

○: Available

-: Not Available