FUNCTION OF MAIN COMPONENTS
The main components in the airbag system have the following functions:
| Components | Outline |
|---|---|
|
*1: Models with SRS front passenger airbag *2: Models with SRS driver knee airbag and SRS curtain shield airbag *3: Models with 1GR-FE engine |
|
| Airbag Sensor Assembly |
·
In the event of a frontal collision, the airbag sensor assembly receives signals from either of the front airbag sensors. The airbag sensor assembly receives the signal via its judgment circuit and also receives another signal from the safing sensor built into the airbag sensor assembly. After receiving a signal from at least one of the front airbag sensors and the safing sensor, the airbag sensor assembly determines whether the SRS driver airbag, SRS front passenger airbag*1, SRS driver knee airbag*2, SRS curtain shield airbags*2 and front seat belt pretensioners*2 should be deployed.
·
In the event of a side collision, the airbag sensor assembly receives signals from the door side airbag sensor. The airbag sensor assembly receives the signal via its judgment circuit and also receives another signal from the safing sensor built into the airbag sensor assembly. After receiving a signal from the door side airbag sensors and safing sensor, the airbag sensor assembly determines whether the SRS curtain shield airbag should be deployed.*2
·
The airbag sensor assembly also diagnoses system malfunctions. |
| Horn Button Assembly | These consist of an inflator, a bag, and so on. The inflator deploys gas in accordance with an expansion signal from the airbag sensor assembly and deploys the bag. |
| Instrument Panel Passenger Airbag Assembly*1 | |
| No. 1 Lower Instrument Panel Airbag Assembly*2 | |
| Curtain Shield Airbag Assembly LH/RH*2 | |
| Front Airbag Sensor LH/RH | Based on the deceleration of the vehicle during a frontal collision, distortion is created in the sensor and converted into an electrical signal. |
| Door Side Airbag Sensor LH/RH*2 | Based on the deceleration of the vehicle during a side collision, distortion is created in the sensor and converted into an electrical signal. |
| Front Seat Outer Belt Assembly LH/RH*2 | The front seat outer belt assemblies are used to help reduce impact to the occupants. |
| Combination Meter Assembly
·
SRS Warning Light |
The SRS warning light turns on to alert the driver when the airbag sensor assembly detects a malfunction in the SRS airbag system. |
| ECM*3 | The ECM performs a fuel cut when the airbags are deployed. |
OPERATING CONDITION
If the impact of a collision is greater than the specified value, the SRS is activated automatically. The airbag sensor assembly includes the safing sensor and deceleration sensor. The safing sensor is designed to turn on at a lower deceleration rate than the deceleration sensor.
In case of a frontal collision, the airbag sensor assembly determines whether airbag deployment is necessary based on signals from the deceleration sensor and the front airbag sensor. If the safing sensor turns on simultaneously, current flows to the squibs to deploy the SRS components as shown in the illustration below. However, a deployment ignition signal may be output with the deceleration sensor ON signal even without a signal from a front airbag sensor.
In case of a side collision, the airbag sensor assembly determines whether airbag deployment is necessary based on signals from the door side airbag sensor. If the safing sensor turns on simultaneously with the door side airbag sensor, current flows to the squibs to deploy the SRS as shown in the illustration below:*
*: Models with SRS driver knee airbag and SRS curtain shield airbag
SYSTEM CONTROL
Airbag for Frontal Collision
There are 4 types of airbags for frontal collisions: the SRS driver airbag, SRS front passenger airbag*1, SRS driver knee airbag*2 and SRS curtain shield airbag*2. These airbags deploy simultaneously. In addition, the front pretensioners contained in the front seat outer belt assemblies are also activated.*2
*1: Models with SRS front passenger airbag
*2: Models with SRS driver knee airbag and SRS curtain shield airbag
Airbag for Side Collision (Models with SRS Driver Knee Airbag and SRS Curtain Shield Airbag)
The airbag for side collisions contains only the SRS curtain shield airbag.
With the airbag for side collisions, if the door side airbag sensor detects an impact, it informs the airbag sensor assembly, which causes the SRS curtain shield airbag to be deployed simultaneously.
Primary Check Illumination Control (Models with VSC)
After the ignition switch is turned to ON, the airbag sensor assembly illuminates the SRS warning light in the combination meter assembly for approximately 6 seconds and conducts the primary check. During the primary check, the ignition of airbags is prohibited and a diagnosis of the airbag sensor assembly is performed. If a malfunction is detected during the primary check, the SRS warning light remains on even after the 6 seconds have elapsed.
DIAGNOSIS
If the airbag sensor assembly detects a malfunction in the SRS airbag system, the airbag sensor assembly stores the malfunction data in memory, in addition to illuminating the SRS warning light.
The airbag sensor assembly outputs the malfunction data as 5-digit Diagnostic Trouble Codes (DTCs) to Global TechStream (GTS).
The DTCs can be read after connecting the Global TechStream (GTS) to the DLC3. For details, refer to the Repair Manual.
If the SRS airbag deploys, the airbag sensor assembly will turn on the SRS warning light. However, in contrast to the ordinary diagnosis function, a DTC will not be stored. The SRS warning light cannot be turned off. After deployment, it is necessary to replace the airbag sensor assembly with a new one.