Home › Engine / Hybrid System › 1VD-FTV (ENGINE MECHANICAL) › CYLINDER BLOCK
RM25T0E _51 Engine / Hybrid System _029207 1VD-FTV ENGINE MECHANICAL _0132958 CYLINDER BLOCK A

1VD-FTV ENGINE MECHANICAL  CYLINDER BLOCK  REPLACEMENT  


PROCEDURE

Hide 11434C 1.REPLACE CYLINDER BLOCK STRAIGHT PIN

NOTICE:

It is not necessary to remove the cylinder block straight pin unless it is being replaced.


a.

Remove the cylinder block straight pin.


b.

Using a plastic-faced hammer, tap in a new cylinder block straight pin to the cylinder block sub-assembly.

Standard Protrusion:
Item Specified Condition
Pin A and Pin B 5.0 to 7.5 mm (0.197 to 0.295 in.)
Pin C 10.5 to 11.5 mm (0.413 to 0.453 in.)
Pin D and Pin F 3.5 to 6.0 mm (0.138 to 0.236 in.)
Pin E 4.5 to 7.0 mm (0.177 to 0.276 in.)


A164620C01
1.615,4.531 2.927,4.531 true 0.302,4.323 0.802,4.323 true 2.417,4.208 2.74,4.531 false 2.823,3.969 3.323,3.969 true 1.438,4.313 2.74,4.531 false 2.677,4.031 2.729,4.531 false 1.458,4.083 1.458,2.667 1.458,2.667 2.958,2.667 true 2.792,2.667 2.792,3.854 true 0.969,0.146 1.281,0.302 0.313,0.156 10 false *a 4.323,0.323 4.635,0.479 0.313,0.156 10 false *b 0.521,2.875 0.833,3.031 0.313,0.156 10 false *c 4.083,4.302 4.396,4.458 0.313,0.156 10 false *d 1.385,2.021 1.698,2.177 0.313,0.156 10 false *e 0.646,5.135 0.927,5.333 0.281,0.198 10 false *f 0.656,6.167 0.927,6.406 0.271,0.24 10 false *g 0.688,7.208 1,7.406 0.313,0.198 10 false *h 2.396,1.948 2.719,2.167 0.323,0.219 10 false *i 1.698,4.958 1.958,5.198 0.26,0.24 10 false *j 1.615,6.115 1.927,6.271 0.313,0.156 10 false *k 1.615,7.146 1.927,7.354 0.313,0.208 10 false *l 5.688,2.75 6,2.906 0.313,0.156 10 false *m 5.75,6.531 6.063,6.688 0.313,0.156 10 false *n 4.677,2.854 4.99,3.01 0.313,0.156 10 false *e 4.76,6.604 5.031,6.844 0.271,0.24 10 false *g 3.01,2.583 3.167,2.781 0.156,0.198 10 false A 1.156,6.604 1.313,6.802 0.156,0.198 10 false B 1.146,7.594 1.302,7.792 0.156,0.198 10 false C 0.177,4.24 0.333,4.438 0.156,0.198 10 false B 3.375,3.885 3.531,4.083 0.156,0.198 10 false B 1.156,5.615 1.313,5.813 0.156,0.198 10 false A 2.979,4.458 3.135,4.656 0.156,0.198 10 false C
*a Front Side *b Upper Side
*c Rear Side *d Lower Side
*e 15 mm (0.591 in.) *f 22 mm (0.866 in.)
*g 16 mm (0.630 in.) *h 12 mm (0.472 in.)
*i Pin A:
5.0 to 7.5 mm (0.197 to 0.295 in.)
*j Pin C:
10.5 to 11.5 mm (0.413 to 0.453 in.)
*k Pin D:
3.5 to 6.0 mm (0.138 to 0.236 in.)
*l Pin E:
4.5 to 7.0 mm (0.177 to 0.276 in.)
*m Pin B:
5.0 to 7.5 mm (0.197 to 0.295 in.)
*n Pin F:
3.5 to 6.0 mm (0.138 to 0.236 in.)



Hide 11431A 2.REPLACE CYLINDER BLOCK TIGHT PLUG

NOTICE:

If water leaks from the cylinder block tight plug or the plug is corroded, replace the cylinder block tight plug.


a.

Remove the cylinder block tight plugs.


b.

Apply adhesive around new cylinder block tight plugs.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Using SST and a hammer, tap in the cylinder block tight plugs to the standard depth.

SST
09950-60010  (09951-00180, 09951-00250, 09951-00350)
09950-70010  (09951-07150)

Standard depth:

1.7 to 2.7 mm (0.0669 to 0.106 in.)


A164619C01
5.135,6.104 3.667,7 3.667,7 3.5,7 true 0.427,0.281 0.74,0.438 0.313,0.156 10 false *a 4.094,0.198 4.406,0.354 0.313,0.156 10 false *b 0.427,2.354 0.74,2.51 0.313,0.156 10 false *c 4.094,2.354 4.406,2.51 0.313,0.156 10 false *d 0.427,5.24 0.74,5.396 0.313,0.156 10 false *e 3.719,4.198 4.031,4.354 0.313,0.156 10 false *f 3.219,6.906 3.677,7.104 0.458,0.198 10 false SST 1.24,0.219 1.396,0.417 0.156,0.198 10 false A 1.031,1.385 1.188,1.583 0.156,0.198 10 true A 1.688,0.531 1.844,0.729 0.156,0.198 10 true B 1.625,1.333 1.781,1.531 0.156,0.198 10 true C 2.094,1.813 2.25,2.01 0.156,0.198 10 true C 4.615,0.75 4.781,0.917 0.167,0.167 10 true A 5.458,0.75 5.625,0.917 0.167,0.167 10 true A 5.063,1.823 5.219,2.021 0.156,0.198 10 true B 5.458,1.823 5.615,2.021 0.156,0.198 10 true B 5.385,2.719 5.552,2.885 0.167,0.167 10 true A 4.958,2.719 5.125,2.885 0.167,0.167 10 true A 5.365,3.813 5.521,4.01 0.156,0.198 10 true B 4.927,3.813 5.083,4.01 0.156,0.198 10 true B 4.333,3.844 4.49,4.042 0.156,0.198 10 true C 1.406,2.813 1.573,2.979 0.167,0.167 10 true A 1.74,4.406 1.906,4.573 0.167,0.167 10 true A 1.573,5.49 1.74,5.656 0.167,0.167 10 true C
*a Front Side *b RH Side
*c Upper Side *d LH Side
*e Rear Side *f Depth



Hide 13411C 3.REPLACE CRANKSHAFT STRAIGHT PIN

NOTICE:

It is not necessary to remove the crankshaft straight pin unless it is being replaced.


a.
A158685

Replace the crankshaft straight pin.