Home › Engine / Hybrid System › 1VD-FTV (ENGINE MECHANICAL) › CYLINDER BLOCK
RM25T0E _51 Engine / Hybrid System _029207 1VD-FTV ENGINE MECHANICAL _0132958 CYLINDER BLOCK A

1VD-FTV ENGINE MECHANICAL  CYLINDER BLOCK  DISASSEMBLY  


PROCEDURE

Hide 1.INSPECT CONNECTING ROD THRUST CLEARANCE

a.
A164562

Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

Standard thrust clearance:

0.14 to 0.54 mm (0.00551 to 0.0213 in.)


Maximum thrust clearance:

0.60 mm (0.0236 in.)


If the thrust clearance is more than the maximum, replace one or more connecting rods as necessary.

If necessary, replace the crankshaft.


Hide 2.INSPECT CONNECTING ROD OIL CLEARANCE

a.

Remove the 2 connecting rod cap bolts.


b.

Using the 2 removed connecting rod cap bolts, remove the connecting rod cap and connecting rod bearing by wiggling the connecting rod cap right and left.

HINT:

Keep the connecting rod bearing inserted in the connecting rod cap.



c.

Clean the crank pin and connecting rod bearing.


d.

Check the crank pin and connecting rod bearing for pitting and scratches.


e.
A164563C01
1.615,1.646 1.615,0.813 true 1.542,1.656 1.833,1.917 0.292,0.26 10 true *a
*a Plastigage


Lay a strip of Plastigage across the crank pin.


f.
A164564C01
1.781,0.969 2.365,0.969 true 2.396,0.875 2.677,1.167 0.281,0.292 10 true *a
*a Protrusion
V100135

Front


Install the connecting rod cap so that its protrusion is facing the correct direction.

NOTICE:

Match the numbered connecting rod cap with the connecting rod.



g.

Apply a light coat of engine oil to the threads of the connecting rod cap bolts.


h.
A164565

Step 1:

Install and uniformly tighten the connecting rod cap bolts in sequence.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not turn the crankshaft.


HINT:
·

The connecting rod bearing cap bolts are tightened in 2 progressive steps.

·

If any connecting rod bearing cap bolt is broken or deformed, replace it.




i.

Step 2:

i.

Mark the front side of each connecting rod cap bolt with paint.


ii.

Tighten the bearing cap bolts in step 1 90°.



j.

Remove the 2 bolts, connecting rod cap and lower bearing.


k.
A164566C01
1.667,1.75 1.667,0.833 true 1.583,1.75 1.917,1.979 0.333,0.229 10 true *a
*a Plastigage


Measure the Plastigage at its widest point.

Standard oil clearance:

0.024 to 0.042 mm (0.000945 to 0.00165 in.)


Maximum oil clearance:

0.052 mm (0.00205 in.)


If the oil clearance is more than the maximum, replace the bearings. If necessary, replace the crankshaft.


l.

If replacing a bearing, replace it with one that has the same number marked on the connecting rod. There are 5 sizes of standard bearings, marked "1 ", "2", "3", "4" and "5" accordingly.

Select the correct bearing by adding together the number marks imprinted on the connecting rod and crankshaft.

EXAMPLE:

Connecting rod "1" (A) + Crank pin "2" (B) = Total number 3 (use bearing "3" (C))

Standard Connecting Rod Big End Inside Diameter (A):
Item Specified Condition
Mark 1 58.000 to 58.006 mm (2.2835 to 2.2837 in.)
Mark 2 58.006 to 58.012 mm (2.2837 to 2.2839 in.)
Mark 3 58.012 to 58.018 mm (2.2839 to 2.2842 in.)


Standard Crankshaft Pin Diameter (B):
Item Specified Condition
Mark 0 54.994 to 55.000 mm (2.1651 to 2.1654 in.)
Mark 1 54.988 to 54.994 mm (2.1649 to 2.1651 in.)
Mark 2 54.982 to 54.988 mm (2.1646 to 2.1649 in.)


Standard Bearing Center Wall Thickness (C):
Item Specified Condition
Mark 1 1.485 to 1.488 mm (0.0585 to 0.0586 in.)
Mark 2 1.488 to 1.491 mm (0.0586 to 0.0587 in.)
Mark 3 1.491 to 1.494 mm (0.0587 to 0.0588 in.)
Mark 4 1.494 to 1.497 mm (0.0588 to 0.0589 in.)
Mark 5 1.497 to 1.500 mm (0.0589 to 0.0591 in.)


A316804C01
1.5,2 1.667,2 1.667,2 2.188,2.302 true 1.5,2.833 1.667,2.833 1.667,2.833 2.198,2.375 true 2.833,2 2.667,2 2.667,2 2.26,2.302 true 2.667,2.917 2.667,2.75 2.667,2.75 2.271,2.385 true 0.833,0.458 1.146,0.615 0.313,0.156 10 false *1 4.594,0.865 4.906,1.021 0.313,0.156 10 false *2 5.635,0.865 5.948,1.021 0.313,0.156 10 false *3 1.344,1.906 1.573,2.073 0.229,0.167 10 true *a 2.854,1.917 3.083,2.073 0.229,0.156 10 true *b 1.344,2.74 1.656,2.896 0.313,0.156 10 false *c 2.573,2.938 2.885,3.094 0.313,0.156 10 false *d
*1 Crankshaft *2 Connecting Rod
*3 Connecting Rod Bearing - -
*a No. 1 and No. 2 *b No. 3 and No. 4
*c No. 5 and No. 6 *d No. 7 and No. 8



m.

Completely remove the Plastigage.


Hide 3.REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.
A164635

Using a ridge reamer, remove all the carbon from the top of the cylinder.


b.

Uniformly loosen the connecting rod bolts, and remove the connecting rod cap with bearing.


c.

Push out the piston sub-assembly and connecting rod with connecting rod bearing through the top of the cylinder block sub-assembly.

HINT:

Arrange the piston and connecting rod assemblies in the correct order.



Hide 13041 4.REMOVE CONNECTING ROD BEARING

a.
A164871

Remove the connecting rod bearings from the connecting rod and connecting rod cap.

HINT:

Arrange the removed parts in the correct order.



Hide 13011 5.REMOVE PISTON RING SET

HINT:

Arrange the piston rings in the correct order.


a.
A164601

Using a piston ring expander, remove the No. 1 compression ring and No. 2 compression ring.


b.

Using a piston ring expander, remove the oil ring rail.


c.

Remove the oil ring expander by hand.


Hide 13101 6.REMOVE PISTON WITH PIN SUB-ASSEMBLY

a.

Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.

If any movement is felt, replace the piston with pin sub-assembly.


b.
A164602

Using a screwdriver, pry out the 2 piston pin hole snap rings.


c.

Gradually heat the piston to approximately 80°C (176°F).


d.
A164603

Using a plastic-faced hammer and brass bar, lightly tap out the piston pin and remove the connecting rod.

HINT:
·

The piston and pin are a matched set.

·

Arrange the pistons, pins, rings, connecting rods and bearings in the correct order.




Hide 13101 7.CLEAN PISTON

a.

Using a gasket scraper, remove the carbon from the piston top.


b.

Using a groove cleaning tool or broken compression ring, clean the piston ring grooves.


c.

Using solvent and a brush, thoroughly clean the piston.

NOTICE:

Do not use a wire brush.



Hide 8.INSPECT CRANKSHAFT THRUST CLEARANCE

a.
A164572

Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

Standard thrust clearance:

0.02 to 0.22 mm (0.000787 to 0.00866 in.)


Maximum thrust clearance:

0.30 mm (0.0118 in.)


If the thrust clearance is more than the maximum, replace the thrust washers as a set.

Standard thrust washer thickness:

2.44 to 2.49 mm (0.0961 to 0.0980 in.)


If necessary, replace the crankshaft.


Hide 13411 9.REMOVE CRANKSHAFT

a.
A164796N01
0.656,0.115 0.865,0.302 0.208,0.188 10 true 1 1.354,0.125 1.542,0.323 0.188,0.198 10 true 5 1.99,0.135 2.188,0.333 0.198,0.198 10 true 9 2.604,0.135 2.792,0.333 0.188,0.198 10 true 8 3.156,0.094 3.281,0.25 0.125,0.156 10 true 4 3.198,1.927 3.365,2.104 0.167,0.177 10 true 3 2.604,1.896 2.792,2.073 0.188,0.177 10 true 7 1.99,1.865 2.229,2.063 0.24,0.198 10 true 10 1.375,1.854 1.615,2.052 0.24,0.198 10 true 6 0.667,1.865 0.906,2.063 0.24,0.198 10 true 2

Using several steps, loosen and remove the 10 crankshaft bearing cap set bolts uniformly in the sequence shown in the illustration.


b.
A164797N01
0.375,0.156 0.531,0.323 0.156,0.167 10 true 1 1.719,0.156 1.885,0.313 0.167,0.156 10 true 9 2.323,0.156 2.521,0.313 0.198,0.156 10 true 8 1.094,0.156 1.25,0.323 0.156,0.167 10 true 5 3.052,0.156 3.229,0.313 0.177,0.156 10 true 4 0.75,0.688 0.927,0.875 0.177,0.188 10 true 11 1.448,0.688 1.625,0.865 0.177,0.177 10 true 15 2.052,0.688 2.26,0.854 0.208,0.167 10 true 19 2.688,0.698 2.927,0.865 0.24,0.167 10 true 18 3.177,0.75 3.396,0.927 0.219,0.177 10 true 14 3.188,1.26 3.396,1.417 0.208,0.156 10 true 13 2.688,1.323 2.885,1.49 0.198,0.167 10 true 17 2.073,1.333 2.26,1.5 0.188,0.167 10 true 20 1.448,1.344 1.635,1.521 0.188,0.177 10 true 16 0.75,1.333 0.938,1.51 0.188,0.177 10 true 12 0.375,1.854 0.531,2.052 0.156,0.198 10 true 2 1.083,1.865 1.24,2.063 0.156,0.198 10 true 6 1.667,1.854 1.927,2.052 0.26,0.198 10 true 10 2.323,1.854 2.479,2.052 0.156,0.198 10 true 7 3.042,1.844 3.198,2.042 0.156,0.198 10 true 3

Using several steps, loosen and remove the 20 crankshaft bearing cap set bolts uniformly in the sequence shown in the illustration.


c.
A164799

Remove the 2 cylinder block stiffening plates.


d.
A164847

Using 2 crankshaft bearing cap set bolts, pull out the 5 crankshaft bearing caps.


e.
A164570

Remove the crankshaft.


Hide 11011 10.REMOVE CRANKSHAFT THRUST WASHER SET

A164600

Hide 11711 11.REMOVE CRANKSHAFT BEARING

HINT:
·

Keep the upper and lower crankshaft bearings and crankshaft bearing cap as a set.

·

Arrange the crankshaft bearing caps and bearings in the correct order.



A164798C01
0.521,0.365 0.833,0.521 0.313,0.156 10 false *1 0.521,2.323 0.833,2.479 0.313,0.156 10 false *2
*1 Lower Crankshaft Bearing
*2 Upper Crankshaft Bearing


Hide 15708 12.REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A164571

Using a 5 mm hexagon wrench, remove the 4 bolts and 4 No. 1 oil nozzle sub-assemblies.


Hide 13.REMOVE CYLINDER BLOCK STUD BOLT

HINT:

If a cylinder block stud bolt is deformed or the threads are damaged, replace it.


Hide 11432R 14.REMOVE CYLINDER BLOCK STRAIGHT SCREW PLUG

HINT:

If water leaks from the cylinder block straight screw plug or the plug is corroded, replace the straight screw plug.


a.

Remove the 4 cylinder block straight screw plugs and 4 gaskets.

A316797C01
5.417,2.833 5.417,2.667 5.417,2.667 5.792,2.115 true 5.333,2.844 5.646,3 0.313,0.156 10 false *1 0.792,0.104 1.104,0.26 0.313,0.156 10 false *a 1.24,2.021 1.552,2.177 0.313,0.156 10 false *b
*1 Gasket - -
*a RH Side *b LH Side
V100136

Front - -