Home › Power Source / Network › 1GR-FE (BATTERY / CHARGING) › GENERATOR
RM25T0E _57 Power Source / Network _029236 1GR-FE BATTERY / CHARGING _0133251 GENERATOR A

1GR-FE BATTERY / CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 27411 1.REMOVE GENERATOR PULLEY

a.

Mount the generator assembly in a vise between aluminum plates.


b.
A323643C01
2.844,1.448 2.844,1.167 2.844,1.167 3.135,0.719 true 2.167,0.198 2.375,0.198 2.375,0.198 2.938,0.521 true 1.698,1.917 2.01,2.115 0.313,0.198 10 true *a 1.573,0.125 2.646,0.323 1.073,0.198 10 false SST 1-B 2.583,1.479 3.323,1.688 0.74,0.208 10 false SST 1-A
*a Hold
V100135

Turn


Install SST 1-A to the generator pulley shaft.

SST
09820-63011  (09820-06010, 09820-06021)

HINT:
SST 1-A and B 09820-06010
SST 2 09820-06021



c.

Install SST 1-B to SST 1-A.


d.

Hold SST 1-A with a torque wrench and turn SST 1-B clockwise with the specified torque.

Torque:
39 N*m (400 kgf*cm, 29 ft.*lbf)

NOTICE:

Make sure that SST is secured to the generator rotor shaft.



e.
A323641C01
2.365,0.5 2.573,0.5 2.573,0.5 2.74,0.885 false 1.917,0.417 2.688,0.615 0.771,0.198 10 false SST 2
V100135

Insert


Insert SST 2 and attach it to the generator pulley nut.


f.
A323642C01
1.271,1.615 1.583,1.813 0.313,0.198 10 true *a
*a Hold
V100135

Turn


To loosen the generator pulley nut, turn SST 1-A in the direction shown in the illustration.

NOTICE:

To prevent damage to the rotor shaft, do not loosen the generator pulley nut more than one-half of a turn.



g.

Remove SST 2 from the generator assembly.


h.
A323644C01
2.167,0.135 2.396,0.135 2.396,0.135 2.917,0.448 true 2.833,1.292 2.833,1.021 2.833,1.021 3.083,0.667 true 2.229,1.719 2.542,1.917 0.313,0.198 10 true *a 1.594,0.052 2.396,0.26 0.802,0.208 10 false SST 1-B 2.573,1.323 3.292,1.51 0.719,0.188 10 false SST 1-A
*a Hold
V100135

Turn


Turn SST 1-B in the direction shown in the illustration and remove SST 1-A and B.


i.

Remove the pulley nut and generator pulley.


Hide 27039 2.REMOVE GENERATOR REAR END COVER

a.
A323645

Remove the 3 bolts and generator rear end cover.


Hide 27387 3.REMOVE TERMINAL INSULATOR

a.
A323646

Remove the terminal insulator from the generator coil assembly.


Hide 27370 4.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A323647

Remove the 2 screws and generator brush holder assembly from the generator coil assembly.


Hide 5.REMOVE GENERATOR COIL ASSEMBLY

a.
A323648

Remove the 4 bolts.


b.
A219662C03
2.083,0.823 2.51,0.688 2.51,0.688 2.604,0.688 false 0.802,0.354 0.99,0.531 0.188,0.177 10 false *a 2.615,0.594 2.927,0.76 0.313,0.167 10 false SST
*a Hold
V100135

Turn


Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)


Hide 27444 6.REMOVE GENERATOR BEARING COVER PACKING

a.
A284548

Remove the generator bearing cover packing.

NOTICE:

If the generator bearing cover packing breaks, remove all broken pieces.


HINT:

The generator bearing cover packing may be installed on the generator rotor assembly.



Hide 27330 7.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A323649

Remove the generator rotor assembly.

NOTICE:

Do not drop the generator rotor assembly.



Hide 8.INSPECT GENERATOR DRIVE END FRAME BEARING

a.
A128080

Check that the generator drive end frame bearing is not rough or worn, and that it rotates smoothly.


Hide 9.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A323650

Remove the 4 screws and retainer plate from generator drive end frame assembly.


b.
A323651N01
0.583,0.865 1.188,0.865 true 1.125,1.219 0.823,1.208 0.823,1.208 0.823,0.875 true 0.281,0.792 0.74,0.99 0.458,0.198 10 false SST

Using SST and a hammer, tap out the generator drive end frame bearing from the generator drive end frame assembly.

SST
09950-60010  09950-70010  (09951-00250, 09951-07100)