Home › Engine / Hybrid System › 1HZ (ENGINE MECHANICAL) › TIMING BELT
RM25T0E _51 Engine / Hybrid System _029355 1HZ ENGINE MECHANICAL _0133477 TIMING BELT A

1HZ ENGINE MECHANICAL  TIMING BELT  INSTALLATION  


PROCEDURE

Hide 13523P 1.INSTALL CAMSHAFT TIMING PULLEY

a.

Install the pulley set key to the key groove of the camshaft.


b.

Align the pulley set key with the key groove of the camshaft timing pulley, and slide the camshaft timing pulley.


c.

Temporarily install the pulley bolt.


d.
A326316C01
1.354,0.073 1.667,0.229 0.313,0.156 10 false *a
*a Hold
V100135

Turn


Hold the hexagon wrench head portion of the camshaft with a wrench, and tighten the pulley bolt.

Torque:
98 N*m (999 kgf*cm, 72 ft.*lbf)


Hide 11201 2.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.

Remove any old seal packing (FIPG) material.


b.
A326317C01
0.552,0.76 1.208,0.313 1.208,0.313 0.552,1.448 true 3.177,1.229 2.302,0.333 2.302,0.333 3.177,0.969 true 1.26,0.219 1.573,0.375 0.313,0.156 10 false *a 2.104,0.229 2.313,0.427 0.208,0.198 10 false *a
*a Seal Line


Apply seal packing to the cylinder head sub-assembly as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent



c.

Install the gasket to the cylinder head cover sub-assembly.


d.

Install the cylinder head cover sub-assembly with the 14 bolts and 2 nuts.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


Hide 13528 4.INSTALL CAMSHAFT DRIVE GEAR

a.
A326318C01
3.073,1.219 2.948,1.219 2.948,1.219 2.573,0.906 true 1.99,1.438 2.448,1.823 2.448,1.823 2.573,1.823 true 0.313,1.854 0.313,1.677 0.313,1.677 0.479,1.5 false 2,0.292 2.125,0.292 2.125,0.292 2.271,0.438 true 0.969,0.385 1.188,0.385 1.188,0.385 1.594,0.74 true 0.323,0.75 0.51,0.75 0.51,0.75 0.823,1.135 true 3.115,1.135 3.365,1.365 0.25,0.229 10 false *1 2.615,1.729 2.917,1.99 0.302,0.26 10 true *2 0.229,1.875 0.552,2.083 0.323,0.208 10 false *3 1.813,0.198 2,0.417 0.188,0.219 10 true *a 0.771,0.302 1.094,0.5 0.323,0.198 10 false *b 0.146,0.656 0.469,0.865 0.323,0.208 10 false *c
*1 Injection Pump Drive Gear
*2 No. 2 Camshaft Timing Pulley Flange
*3 Camshaft Drive Gear
*a Knock Pin
*b Knock Pin Hole
*c Knock Pin Groove


Align the knock pin hole of the No. 2 camshaft timing pulley flange and the knock pin groove of the camshaft drive gear with the knock pin on the injection pump drive gear.


b.
A326319C01
2.104,1.219 1.99,0.49 1.99,0.49 2.198,1.167 true 1.885,0.313 2.083,0.51 0.198,0.198 10 true *a
*a Matchmarks


Align the No. 1 camshaft timing pulley flange with the matchmarks of the camshaft drive gear and install the No. 1 camshaft timing pulley flange with the 4 bolts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 13505 5.INSTALL NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

a.

Apply adhesive 2 or 3 threads of the pivot bolt.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



b.

Using an 8 mm hexagon wrench, install the plate washer and No. 1 timing belt idler sub-assembly with the pivot bolt.

Torque:
34.5 N*m (352 kgf*cm, 25 ft.*lbf)


c.

Check that the No. 1 timing belt idler sub-assembly moves smoothly.


Hide 6.SET NO. 1 CYLINDER TO BDC/COMPRESSION

a.
A326320C01
3.042,1.583 3.042,0.667 true 1.344,2.052 1.177,2.052 1.177,2.052 0.865,1.635 true 0.229,0.927 0.333,0.927 0.333,0.927 0.573,1.375 true 2.208,0.146 2.365,0.146 2.365,0.146 2.667,0.333 true 2.948,1.615 3.26,1.771 0.313,0.156 10 false *1 1.375,1.969 1.625,2.156 0.25,0.188 10 true *2 0.052,0.833 0.292,1.052 0.24,0.219 10 false *a 2.031,0.052 2.344,0.25 0.313,0.198 10 false *a
*1 Camshaft Timing Pulley
*2 No. 2 Camshaft Timing Pulley Flange
*a Timing Mark


Check that the timing mark of the No. 2 camshaft timing pulley flange with the BDC mark.

NOTICE:

Do not turn the crankshaft pulley. The valve heads will hit against the piston top.



b.

Align the timing mark of the camshaft timing pulley with the BDC mark.


Hide 13568 7.INSTALL TIMING BELT

NOTICE:

The engine should be cold.


HINT:
A326321

If re-using timing belt, align the points marked during removal, and install the timing belt with the arrow pointing in the direction of engine revolution.


a.

Remove any oil or water on the pulleys, and keep them clean.

NOTICE:

Only wipe the pulleys, do not use any cleansing agent.



b.

Install the timing belt under tension between the camshaft timing pulley and camshaft drive gear.


Hide 13540 8.SET NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A326322C01
1.74,1.365 1.74,1.146 1.74,1.146 1.375,1.01 false 1.656,1.385 1.854,1.563 0.198,0.177 10 false *a
*a 1.5 mm Hexagon Wrench


Using a press slowly press in the push rod using 981 to 9807 N*m (100 to 1000 kgf*cm, 220 to 2205 ft.*lbf) of force.


b.

Align the holes of the push rod and housing, pass a hexagon wrench (1.5 mm (0.0591 in.)) through the holes to keep the setting position on the push rod.


c.

Release the press.


Hide 13540 9.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A326323C01
0.51,0.26 0.75,0.26 0.75,0.26 1.438,0.833 true 0.333,0.167 0.552,0.375 0.219,0.208 10 false *a
*a Hexagon Wrench (1.5 mm (0.0591 in.))


Temporarily install the No. 1 chain tensioner assembly with the 2 bolts while pushing the pulley toward the timing belt.


b.

Alternately tighten the 2 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


c.

Remove the hexagon wrench (1.5 mm (0.0591 in.)).


Hide 10.CHECK VALVE TIMING

a.
A326324C01
0.292,1.469 0.292,1.26 0.292,1.26 0.604,0.917 true 0.302,3.167 0.5,3.167 0.5,3.167 0.708,3.635 true 1.844,4.281 2.083,4.281 2.083,4.281 2.427,3.865 true 0.125,3.094 0.375,3.323 0.25,0.229 10 false *a 0.208,1.49 0.521,1.646 0.313,0.156 10 false *a 1.677,4.198 1.99,4.354 0.313,0.156 10 false *a
*a Timing Mark


Turn the crankshaft pulley clockwise and check that each pulley timing mark aligns with the TDC marks.

If the marks do not align, remove the timing belt and reinstall it.


Hide 11322A 11.INSTALL NO. 1 TIMING BELT COVER

a.

Remove any old seal packing (FIPG) material.


b.
A326325C01
0,0 0,0 false
V100145

Apply Seal Packing


Apply seal packing to the camshaft oil seal retainer and No. 2 timing gear cover as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent



c.

Check that timing belt cover gasket have cracks or peeling, etc.

If the gasket cracks or peeling, etc. replace it using these steps:

i.

Using a screwdriver and gasket scraper, remove all the old gasket material.


ii.

Thoroughly clean all components to remove all the loose material.


iii.
A326326C01
0.917,0.375 1.104,0.375 1.104,0.375 1.375,0.719 true 0.729,0.281 1,0.479 0.271,0.198 10 false *a
*a Gasket


Remove the backing paper from a new gasket and install the gasket evenly to the part of the No. 1 timing belt cover shaded black in the illustration.

NOTICE:

Do not leave a gap between them. Cut off any excess gasket.



iv.

After installing the gasket, press down on it so that the adhesive firmly sticks to the No. 1 timing belt cover.



d.

Install the No. 1 timing belt cover with the 6 seal washers and 6 bolts.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)