Home › Engine / Hybrid System › 1HZ (ENGINE MECHANICAL) › CYLINDER HEAD
RM25T0E _51 Engine / Hybrid System _029355 1HZ ENGINE MECHANICAL _0133480 CYLINDER HEAD G

1HZ ENGINE MECHANICAL  CYLINDER HEAD  INSPECTION  


PROCEDURE

Hide 11101 1.CLEAN CYLINDER HEAD SUB-ASSEMBLY

a.

Clean the cylinder head sub-assembly.

i.

Turn the crankshaft and bring each piston to top dead center (TDC). Using a gasket scraper, remove all the carbon from the piston top.


ii.

Remove all the gasket material from the top of the cylinder block.

NOTICE:

Be careful not to scratch the surfaces.



iii.

Using compressed air, blow carbon and oil from the bolt holes.

CAUTION:

Protect your eyes when using high pressure air.



iv.

Using a gasket scraper, remove all the gasket material from the manifold and cylinder head sub-assembly surfaces.

NOTICE:

Be careful not to scratch the surfaces.




b.

Using a wire brush, remove all the carbon from the combustion chamber assemblies.

NOTICE:

Do not scratch the surface that contacts the cylinder block.



c.
A326288

Using a valve guide bushing brush and solvent, clean all the valve guide bushes.


d.

Using a soft brush and solvent, thoroughly clean the cylinder head sub-assembly.


Hide 11101 2.INSPECT CYLINDER HEAD SUB-ASSEMBLY

a.
A326289C01
0.094,2.229 0.313,2.427 0.219,0.198 10 false *a 0.146,3.219 0.354,3.406 0.208,0.188 10 false *b 0.042,3.938 0.229,4.125 0.188,0.188 10 false *c
*a Cylinder Block Side
*b Intake Manifold Side
*c Exhaust Manifold Side


Inspect the cylinder head sub-assembly warpage.

i.

Using a precision straightedge and feeler gauge, measure the surfaces that contact the cylinder block and the manifolds for warpage.

Maximum warpage:

0.20 mm (0.00787 in.)


If the warpage is more than the maximum, replace the cylinder head sub-assembly.



b.

Inspect the cylinder head sub-assembly for cracks.

i.

Using a dye penetrant, check the combustion chamber, intake ports, exhaust ports and cylinder head sub-assembly surface for cracks.

If cracked, replace the cylinder head sub-assembly.



Hide 3.CLEAN VALVE

a.

Using a gasket scraper, chip off any carbon from the valve head.


b.

Using a wire brush, thoroughly clean the valve.


Hide 13711 4.INSPECT VALVE

a.

Using a micrometer, measure the diameter of the valve stem.

Standard Valve Stem Diameter:
Item Specified Condition
Intake valve 7.975 to 7.990 mm (0.3140 to 0.3146 in.)
Exhaust valve 7.960 to 7.975 mm (0.3134 to 0.3140 in.)


If the diameter is not as specified, replace the valve.


b.
A329219C01
3.031,1.781 3.344,1.938 0.313,0.156 10 false *a
*a Valve Face Angle


Check the valve face angle.

i.

Grind the valve enough to remove any pits and carbon.


ii.

Check that the valve is ground to the correct valve face angle.

Standard valve face angle:

44.5°


If the valve is worn, replace the valve.



c.
A053643C01
0.521,1.667 0.719,1.833 0.198,0.167 10 false *a
*a Margin Thickness


Check the head margin thickness.

Standard Margin Thickness:
Item Specified Condition
Intake valve 1.6 mm (0.0630 in.)
Exhaust valve 1.7 mm (0.0669 in.)


Minimum Margin Thickness:
Item Specified Condition
Intake valve 1.1 mm (0.0433 in.)
Exhaust valve 1.2 mm (0.0472 in.)


If the margin thickness is less than the minimum, replace the valve.


d.

Check the overall length of the valve.

Standard Overall Length:
Item Specified Condition
Intake valve 103.29 to 103.69 mm (4.067 to 4.082 in.)
Exhaust valve 103.14 to 103.54 mm (4.061 to 4.076 in.)


Minimum Overall Length:
Item Specified Condition
Intake valve 102.79 mm (4.047 in.)
Exhaust valve 102.64 mm (4.041 in.)


If the overall length is less than the minimum, replace the valve.


e.
A053828

Check the surface of the valve stem tip for wear. If the valve stem tip is worn, resurface the tip with a grinder or replace the valve.

NOTICE:

Do not grind the valve so it becomes shorter than the minimum overall length.



Hide 13711B 5.INSPECT COMPRESSION SPRING

a.
A053807C01
1.938,0.042 2.25,0.198 0.313,0.156 10 false *a
*a Deviation


Using a steel square, measure the deviation of the compression spring.

Maximum deviation:

2.0 mm (0.0787 in.)


If the deviation is more than the maximum, replace the compression spring.


b.

Using a vernier caliper, measure the free length of the compression spring.

Standard free length:

46.20 mm (1.82 in.)


If the free length is not as specified, replace the compression spring.


c.
EM00281

Using a spring tester, measure the tension of the compression spring at the installed length.

Standard tension:

301 to 332 N (31 to 34 kgf, 66.6 to 74.6 lbf) at 37.0 mm (1.46 in.)


If the tension is not as specified, replace the compression spring.


Hide 11122 6.INSPECT VALVE GUIDE BUSH

a.
A326290

Using a caliper gauge, measure the inside diameter of the valve guide bush.

Standard bush inside diameter:

8.010 to 8.030 mm (0.315 to 0.316 in.)



b.

Subtract the valve stem diameter measurement from the valve guide bush inside diameter measurement.

Standard Oil Clearance:
Item Specified Condition
Intake valve guide bush 0.020 to 0.055 mm (0.000787 to 0.00217 in.)
Exhaust valve guide bush 0.035 to 0.070 mm (0.00138 to 0.00276 in.)


Maximum Oil Clearance:
Item Specified Condition
Intake valve guide bush 0.08 mm (0.00315 in.)
Exhaust valve guide bush 0.10 mm (0.00394 in.)


If the clearance is more than the maximum, replace the valve and valve guide bush.


Hide 7.INSPECT VALVE SEAT

a.
A326296C01
0.458,0.5 0.656,0.5 0.656,0.5 1.094,0.854 true 0.281,0.406 0.458,0.604 0.177,0.198 10 false *a
*a 45° Carbide Cutter


Using a 45° carbide cutter, resurface the valve seats. Remove only enough metal to clean the valve seats.


b.
A334452C01
1.594,1.281 1.906,1.438 0.313,0.156 10 false *a
*a Width


Check the valve seating position.

i.

Apply a light coat of Prussian blue to the valve face.


ii.

Lightly press the valve against the seat. Do not rotate valve.


iii.

Prussian blue appears 360° around the entire valve face, the valve is concentric. If not, replace the valve.


iv.

Prussian blue appears 360° around the entire valve seat, the guide and face are concentric. If not, resurface the seat.


v.

Check that the seat contacts the middle of the valve face with the width below:

Standard Width:
Item Specified Condition
Intake Side 1.5 to 1.9 mm (0.0591 to 0.0748 in.)
Exhaust side 1.8 to 2.2 mm (0.0709 to 0.0866 in.)