Home › Engine / Hybrid System › 1HZ (ENGINE MECHANICAL) › CYLINDER BLOCK
RM25T0E _51 Engine / Hybrid System _029355 1HZ ENGINE MECHANICAL _0133481 CYLINDER BLOCK G

1HZ ENGINE MECHANICAL  CYLINDER BLOCK  INSPECTION  


PROCEDURE

Hide 11401 1.CLEAN CYLINDER BLOCK SUB-ASSEMBLY

a.

Using a gasket scraper, remove all the gasket material from the top surface of the cylinder block sub-assembly.


b.

Using a soft brush and solvent, thoroughly clean the cylinder block sub-assembly.

NOTICE:

If the cylinder is washed at high temperatures, the cylinder liner sticks out beyond the cylinder block sub-assembly. Always wash the cylinder block sub-assembly at a temperature of 45°C (113°F) or less.



Hide 11401 2.INSPECT CYLINDER BLOCK SUB-ASSEMBLY

a.
A321621

Inspect for flatness.

i.

Using a precision straightedge and feeler gauge, measure the surfaces that contacts the cylinder head and main bearing cap for warpage.

Maximum warpage:

0.20 mm (0.00787 in.)


If the warpage is more than the maximum, replace the cylinder block sub-assembly.



b.

Visually check the cylinder for vertical scratches. If deep scratches are present, rebore all 6 cylinders. If necessary, replace the cylinder block sub-assembly.


Hide 3.INSPECT CYLINDER BORE

a.
A321622C01
2.396,0.958 2.552,0.75 2.552,0.75 2.719,0.75 true 2.344,0.969 2.625,0.469 2.625,0.469 2.792,0.469 true 2.271,1 2.615,0.188 2.615,0.188 2.781,0.188 true 1.625,1.802 1.625,1.604 1.625,1.604 2.063,1.125 true 2.125,1.802 2.125,1.625 2.125,1.625 2.125,1.125 true 2.75,1.813 2.75,1.625 2.75,1.625 2.198,1.094 true 1.552,1.823 1.865,1.979 0.313,0.156 10 false *a 2.063,1.823 2.375,1.979 0.313,0.156 10 false *b 2.677,1.823 2.99,1.979 0.313,0.156 10 false *c 2.813,0.094 3.125,0.25 0.313,0.156 10 false *d 2.823,0.375 3.135,0.531 0.313,0.156 10 false *e 2.76,0.667 3.073,0.823 0.313,0.156 10 false *f 2.51,0.854 2.844,1.115 0.333,0.26 10 false *g
*a No. 1
*b No. 2
*c No. 3
*d No. 4
*e No. 5
*f No. 6
*g Mark 1, 2 or 3
V100135

Front


Inspect the cylinder bore diameter.

HINT:

There are 3 sizes of the standard cylinder bore diameter, marked "1", "2" and "3" accordingly. The mark is stamped on the lower left rear of the cylinder block sub-assembly.


i.
A321623C01
1.531,0.406 1.917,0.188 1.917,0.188 2.094,0.188 true 0.896,0.219 1.083,0.219 1.083,0.219 1.427,0.542 true 2.125,0.094 2.302,0.25 0.177,0.156 10 true *a 0.708,0.135 0.885,0.292 0.177,0.156 10 true *b 0.927,1.667 1.146,1.875 0.219,0.208 10 false *c 0.823,0.667 1.063,0.854 0.24,0.188 10 false *d 2.219,1.302 2.51,1.542 0.292,0.24 10 false *e 2.229,2.031 2.531,2.26 0.302,0.229 10 false *e 1.5,1.344 1.615,1.521 0.115,0.177 10 true A 1.51,1.688 1.635,1.885 0.125,0.198 10 true B 1.5,2.01 1.615,2.198 0.115,0.188 10 true C
*a Thrust Direction
*b Axial Direction
*c Center
*d Front
*e 10 mm (0.394 in.)


Using a cylinder gauge, measure the cylinder bore diameter at positions A, B and C in the thrust and axial directions.

Reference Value (New Parts):
Item Specified Condition
Mark 1 94.000 to 94.010 mm (3.7008 to 3.7012 in.)
Mark 2 94.010 to 94.020 mm (3.7012 to 3.7016 in.)
Mark 3 94.020 to 94.030 mm (3.7016 to 3.7020 in.)


Maximum Diameter:
STD 94.230 mm (3.7098 in.)
O/S 0.50 94.730 mm (3.7295 in.)


If the diameter is more than the maximum, rebore all cylinders. If necessary, replace the cylinder block sub-assembly.



Hide 4.CLEAN PISTON SUB-ASSEMBLY WITH PIN

a.

Using a gasket scraper, remove the carbon from the piston top.


b.

Using a groove cleaning tool or broken ring, clean the piston ring grooves.


c.

Using solvent and a brush, thoroughly clean the piston.

NOTICE:

Do not use a wire brush.



Hide 5.INSPECT PISTON

HINT:

There are 3 sizes of standard piston diameter, marked "1", "2" and "3" accordingly. The mark is stamped on the piston top.


a.
A326279C01
2.927,1.542 3.208,1.75 0.281,0.208 10 false *a
*a Distance


Using a micrometer, measure the piston diameter at right angles to the piston center line where the distance from the piston head is as specified.

Distance:

41.6 mm (1.64 in.)


Reference Value (New Parts):
Item Specified Condition
Mark 1 93.885 to 93.895 mm (3.69625 to 3.69665 in.)
Mark 2 93.896 to 93.905 mm (3.69669 to 3.69704 in.)
Mark 3 93.906 to 93.915 mm (3.69708 to 3.69743 in.)



b.

Measure the cylinder bore diameter in the thrust directions.


c.

Subtract the piston diameter measurement from the cylinder bore diameter measurement.

Reference value (new parts):

0.105 to 0.125 mm (0.00413 to 0.00492 in.)


Maximum oil clearance:

0.125 mm (0.00492 in.)


If the oil clearance is more than the maximum, replace all 6 pistons. If necessary, replace the cylinder block sub-assembly.

HINT:
A326280C01
2.104,2.688 2.667,2.688 true 0.688,3 0.875,3 0.875,3 1.313,2.75 true 1.813,1.781 2.438,1.781 true 1.979,1.542 2.208,1.542 2.208,1.542 2.531,1.729 false 2.146,1.313 2.271,1.313 2.271,1.313 2.604,1.688 false 3.177,1.906 3.177,1.677 3.177,1.677 2.844,1.563 true 2.875,2.188 2.875,1.979 2.875,1.979 2.771,1.625 true 2.417,2.313 2.563,2.313 2.563,2.313 2.698,1.656 true 0.354,0.406 0.542,0.406 0.542,0.406 0.854,0.781 false 0.583,2.5 0.813,2.5 0.813,2.5 1.094,2.708 false 0.167,0.344 0.365,0.521 0.198,0.177 10 false *1 0.396,2.448 0.677,2.656 0.281,0.208 10 false *2 1.625,1.698 1.938,1.854 0.313,0.156 10 false *a 1.792,1.458 2.104,1.615 0.313,0.156 10 false *b 1.979,1.219 2.292,1.375 0.313,0.156 10 false *c 2.24,2.229 2.552,2.385 0.313,0.156 10 false *d 2.802,2.198 3.115,2.354 0.313,0.156 10 false *e 3.104,1.927 3.375,2.135 0.271,0.208 10 false *f 0.5,2.906 0.854,3.167 0.354,0.26 10 false *g 2.521,0.396 2.875,0.604 0.354,0.208 10 false *h 2.698,2.604 3.052,2.813 0.354,0.208 10 false *h
*1 Cylinder Block Sub-assembly
*2 PISTON
*a No. 1
*b No. 2
*c No. 3
*d No. 4
*e No. 5
*f No. 6
*g Front Mark
*h Mark 1, 2 or 3


Use a piston with the same number mark as the cylinder bore diameter marked on the cylinder block sub-assembly.



Hide 6.INSPECT PISTON PIN OIL CLEARANCE

a.

Inspect the piston pin fit.

i.

Heat the piston to approximately 80°C (176°F), and push the piston pin into the piston pin hole with your thumb.

If the pin can be installed at a lower temperature, replace the piston and pin as a set.



b.
A321632

Using a caliper gauge, measure the inside diameter of the connecting rod bush.

Standard bush inside diameter:

29.008 to 29.020 mm (1.1420 to 1.1425 in.)



c.
A321633

Using a micrometer, measure the piston pin diameter.

Standard piston pin diameter:

29.000 to 29.012 mm (1.1417 to 1.1422 in.)



d.

Subtract the piston pin diameter measurement from the bush inside diameter measurement.

Standard oil clearance:

0.004 to 0.012 mm (0.000157 to 0.000472 in.)


Maximum oil clearance:

0.030 mm (0.00118 in.)



Hide 7.INSPECT RING GROOVE CLEARANCE

a.

Inspect the ring groove clearance.

i.
A326281

No. 1 compression ring:

Using a feeler gauge, measure the clearance between a new piston ring and the wall of the ring groove.

Standard ring groove clearance:

0.054 to 0.095 mm (0.00213 to 0.00374 in.)


Maximum ring groove clearance:

0.20 mm (0.00787 in.)


If the clearance is more than the maximum, replace the piston.


ii.
A326282

No. 2 compression ring and oil ring:

Using a feeler gauge, measure the clearance between a new piston ring and the wall of the ring groove.

Standard Ring Groove Clearance:
Item Specified Condition
No. 2 compression ring 0.060 to 0.100 mm (0.00236 to 0.00394 in.)
Oil ring 0.030 to 0.070 mm (0.00118 to 0.00276 in.)


Maximum ring groove clearance:

0.20 mm (0.00787 in.)




Hide 8.INSPECT PISTON RING END GAP

a.

Insert the piston ring into the cylinder bore.


b.

Using a piston, push the piston ring a little beyond the bottom of the ring travel, 130 mm (5.12 in.) from the top of the cylinder block sub-assembly.


c.

Using a feeler gauge, measure the piston ring end gap.

Standard Piston Ring End Gap:
Item Specified Condition
No. 1 compression ring 0.270 to 0.370 mm (0.0106 to 0.0146 in.)
No. 2 compression ring 0.450 to 0.550 mm (0.0177 to 0.0217 in.)
Oil Ring 0.200 to 0.400 mm (0.00787 to 0.0157 in.)


Maximum Piston Ring End Gap:
Item Specified Condition
No. 1 compression ring 0.850 mm (0.0335 in.)
No. 2 compression ring 0.900 mm (0.0354 in.)
Oil Ring 0.880 mm (0.0346 in.)


If the end gap is more than the maximum, replace the piston ring. If the end gap is more than the maximum even with a new piston ring, rebore all 6 cylinders or replace the cylinder block sub-assembly.


Hide 13201 9.INSPECT CONNECTING ROD SUB-ASSEMBLY

a.

Using a rod aligner and feeler gauge, check the connecting rod alignment.

i.
A321629

Check for bend.

Maximum bend:

0.03 mm (0.00118 in.) per 100 mm (3.94 in.)


If the bend is more than the maximum, replace the connecting rod sub-assembly.


ii.
A321630

Check for twist.

Maximum twist:

0.15 mm (0.00591 in.) per 100 mm (3.94 in.)


If the twist is more than the maximum, replace the connecting rod sub-assembly.



Hide 13265 10.INSPECT CONNECTING ROD BOLT

a.
A321631C01
0.281,1.896 0.5,2.094 0.219,0.198 10 false *a 2.896,1.01 3.125,1.208 0.229,0.198 10 false *b
*a Measuring Point
*b Compressed


Using a vernier caliper, measure the minimum diameter of the compressed bolt at the measuring point.

Standard diameter:

8.300 to 8.400 mm (0.327 to 0.331 in.)


Minimum diameter:

7.950 mm (0.313 in.)


If the diameter is less than the minimum, replace the connecting rod bolt.


Hide 11.INSPECT MAIN BEARING CAP BOLT

a.
A321625C01
0.385,1.885 0.563,2.083 0.177,0.198 10 false *a 2.948,1 3.26,1.156 0.313,0.156 10 false *b
*a Measuring Point
*b Elongated Thread


Using a vernier caliper, measure the minimum diameter of the elongated thread at the measuring point.

Standard diameter:

11.800 to 12.000 mm (0.465 to 0.472 in.)


Minimum diameter:

11.50 mm (0.453 in.)


If the diameter is less than the minimum, replace the main bearing cap bolt.


Hide 13411 12.INSPECT CRANKSHAFT

a.

Inspect for circle runout.

i.

Place the crankshaft on V-blocks.


ii.

Using a dial indicator, measure the circle runout at the center journal.

Maximum circle runout:

0.06 mm (0.00236 in.)


If the circle runout is more than the maximum, replace the crankshaft.



b.
A326258C01
0.042,0.073 0.354,0.229 0.313,0.156 10 false *a 0.094,2.51 0.406,2.667 0.313,0.156 10 false *b
*a Main Journal
*b Crank Pin


Inspect the main journals and crank pins.

i.

Using a micrometer, measure the diameter of each main journal and crank pin.

Standard Diameter:
Item Specified Condition
Main journal 66.982 to 67.000 mm (2.6371 to 2.6378 in.)
Crank pin 58.982 to 59.000 mm (2.3221 to 2.3228 in.)


If the diameter is not as specified, check the oil clearance. If necessary, replace the crankshaft.


ii.

Check each main journal and crank pin for taper and out of round as shown in the illustration.

Maximum taper and out of round:

0.02 mm (0.000787 in.)


If the taper and out of round is more than the maximum, replace the crankshaft.



c.

If necessary, grind and hone the main journals and/or crank pins.

i.

Grind and hone the main journals and/or crank pins to the finished undersized diameter.


ii.

Install new main journal and/or crankshaft pin undersized bearing.



Hide 13.INSPECT CHECK VALVE

a.
A118168

Push the valve with a wooden stick to check if it is stuck.

If stuck, replace the check valve.


Hide 15708 14.INSPECT NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.

Check the No. 1 oil nozzle sub-assembly for damage or clogging.

If necessary, replace the No. 1 oil nozzle sub-assembly.