Home › Engine / Hybrid System › 1HZ (ENGINE MECHANICAL) › ENGINE UNIT
RM25T0E _51 Engine / Hybrid System _029355 1HZ ENGINE MECHANICAL _0133486 ENGINE UNIT A

1HZ ENGINE MECHANICAL  ENGINE UNIT  REPLACEMENT  


PROCEDURE

Hide 13613D 1.REPLACE RADIAL BALL BEARING

a.
A329196N01
0.594,1.385 0.594,1.219 0.594,1.219 1.104,0.979 false 0.875,1.854 1.083,1.854 1.083,1.854 1.521,1.594 true 0.469,1.417 0.844,1.604 0.375,0.188 10 false SST 0.563,1.781 0.938,1.969 0.375,0.188 10 false SST

Using SST, remove the radial ball bearing.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04041)
09950-60010  (09951-00230)


b.
A329197N01
1.906,1.198 2.208,0.917 2.208,0.917 2.417,0.917 false 2.469,0.844 2.823,1.073 0.354,0.229 10 false SST

Using SST and a press, press in a new radial ball bearing.

SST
09214-76011  


Hide 11305A 2.REPLACE OIL SEAL

a.

If camshaft oil seal retainer is removed from the cylinder head sub-assembly:

i.
A331233C01
0.958,1.167 1.229,1.167 1.229,1.167 1.594,1.313 true 0.76,1.073 1.073,1.229 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver and hammer, tap out the oil seal.

HINT:

Tape the screwdriver tip before use.



ii.
A331234N01
1.646,1.229 1.969,0.917 1.969,0.917 2.188,0.917 true 2.25,0.854 2.667,1.104 0.417,0.25 10 false SST

Using SST and a hammer, tap in a new oil seal until its surface is flush with the camshaft oil seal retainer edge.

SST
09223-46011  


iii.

Apply MP grease to the oil seal lip.



b.
A331250C01
1.01,1.26 1.24,1.26 1.24,1.26 1.719,0.615 true 0.833,1.167 1.146,1.323 0.313,0.156 10 false *a
*a Protective Tape


If camshaft oil seal retainer is installed to the cylinder head sub-assembly:

i.

Using a screwdriver, pry out the oil seal.

HINT:

Tape the screwdriver tip before use.



ii.
A331251N01
0.406,0.708 0.604,0.708 0.604,0.708 1.104,0.938 true 0.094,0.646 0.49,0.865 0.396,0.219 10 false SST

Using SST and a hammer, tap in a new oil seal until its surface is flush with the camshaft oil seal retainer edge.

SST
09223-46011  


iii.

Apply MP grease to the oil seal lip.



Hide 11302A 3.REPLACE FRONT CRANKSHAFT OIL SEAL

a.
A329199C01
2.01,1.479 3.115,1.479 true 3.146,1.385 3.375,1.583 0.229,0.198 10 false *a
*a Protective Tape


Using a screwdriver and hammer, tap out the front crankshaft oil seal.

HINT:

Tape the screwdriver tip before use.



b.
A329200N01
0.74,1.875 0.969,1.875 0.969,1.875 1.458,1.469 true 0.438,1.802 0.75,2.01 0.313,0.208 10 false SST

Using SST and a hammer, tap in a new front crankshaft oil seal until its surface is flush with the No. 2 timing gear cover edge.

SST
09223-78010  


c.

Apply MP grease to the front crankshaft oil seal lip.


Hide 11381A 4.REPLACE REAR CRANKSHAFT OIL SEAL

a.
A326260

Using a screwdriver and hammer, tap out the rear crankshaft oil seal.

NOTICE:

Be careful not to damage the rear engine oil seal retainer.



b.
A326261N01
1.729,1.354 1.948,1.271 1.948,1.271 2.167,1.271 false 2.219,1.198 2.583,1.375 0.365,0.177 10 false SST

Using SST and a hammer, tap in a new rear crankshaft oil seal until its surface is flush with the rear engine oil seal retainer edge.

SST
09223-56010  


c.

Apply MP grease to the lip of the rear crankshaft oil seal.


Hide 5.REPLACE INJECTION PUMP DRIVE GEAR OIL SEAL

a.

If No. 2 timing gear cover is removed from cylinder block.

i.
A329203C01
1.292,1.458 1.594,1.302 1.594,1.302 1.854,1.302 true 1.896,1.219 2.208,1.375 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver and hammer, tap out the injection pump drive gear oil seal.

HINT:

Tape the screwdriver tip before use.



ii.

Apply MP grease to the injection pump drive gear oil seal lip.


iii.
A329204N01
2.094,1.438 2.573,1.833 2.573,1.833 2.76,1.833 true 2.823,1.771 3.208,1.938 0.385,0.167 10 false SST

Using SST and a hammer, tap in a new injection pump drive gear oil seal until its surface is flush with the No. 2 timing gear cover edge.

SST
09214-76011  



b.

If the No. 2 timing gear cover is installed to the cylinder block.

i.
A329205C01
0.74,0.615 0.948,0.615 0.948,0.615 1.802,0.865 true 0.573,0.531 0.833,0.781 0.26,0.25 10 false *a
*a Protective Tape


Using a screwdriver, pry out the injection pump drive gear oil seal.

NOTICE:

Be careful not to damage the injection pump drive gear.


HINT:

Tape the screwdriver tip before use.



ii.
A329206N02
0.625,0.76 0.854,0.76 0.854,0.76 1.375,1.156 true 0.313,0.698 0.688,0.917 0.375,0.219 10 false SST

Using SST and a hammer, tap in a new injection pump driver gear oil seal until its surface is flush with the No. 2 timing gear cover edge.

SST
09214-76011  


iii.

Apply MP grease to the injection pump drive gear oil seal lip.