Home › Engine / Hybrid System › 1HZ (ENGINE MECHANICAL) › DRIVE BELT
RM25T0E _51 Engine / Hybrid System _029355 1HZ ENGINE MECHANICAL _0133487 DRIVE BELT G

1HZ ENGINE MECHANICAL  DRIVE BELT  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 16361A 1.INSPECT FAN AND GENERATOR V BELT

a.
A329275C01
1.333,0.198 1.646,0.354 0.313,0.156 10 false *a 2.563,0.188 2.875,0.344 0.313,0.156 10 false *b 0.49,0.76 0.771,1 0.281,0.24 10 false *c
*a CORRECT
*b INCORRECT
*c Clearance


Visually check the fan and generator V belt for cracks, oiliness or wear.

Check that the fan and generator V belt does not touch the bottom of the pulley groove.

If necessary, replace the fan and generator V belt.


b.
A329276C01
0.208,1.563 0.208,1.365 0.208,1.365 0.427,1.083 true 2.24,1.844 2.427,1.979 2.427,1.979 2.583,1.979 false 0.125,1.604 0.396,1.833 0.271,0.229 10 false *1 1.417,0.563 1.729,0.719 0.313,0.156 10 false *2 2.625,1.906 2.938,2.063 0.313,0.156 10 false *3
*1 Generator Assembly
*2 Engine Water Pump Assembly
*3 Crankshaft Pulley


Check the fan and generator V belt deflection by pressing on the fan and generator V belt at the points indicated in the illustration with 98 N (10 kgf, 22.0 lbf) of force.

Standard Deflection:
Item Specified Condition
New belt 6.0 to 7.0 mm (0.236 to 0.276 in.)
Used belt 8.0 to 11.0 mm (0.315 to 0.433 in.)


If the deflection is not as specified, adjust it.


c.
A329277C01
0.427,1.344 0.594,1.344 0.594,1.344 0.823,1.552 false 2.313,0.573 2.542,0.385 2.542,0.385 2.729,0.385 false 0.25,1.271 0.552,1.469 0.302,0.198 10 false *a 2.781,0.313 3.094,0.469 0.313,0.156 10 false *b
*a Belt Tension Gauge
*b Belt Tension Gauge Cable


Reference:

Using belt tension gauge and belt tension gauge cable, measure the fan and generator V belt tension.

Standard Tension:
Item Specified Condition
New belt 441 to 539 N (45 to 55 kgf)
Used belt 245 to 343 N (25 to 35 kgf)


If the belt tension is not as specified, adjust it.

NOTICE:
·

Check the fan and generator V belt tension at the specified point.

·

When installing a new fan and generator V belt, set its deflection value as specified.

·

Perform the fan and generator V belt tension and deflection value check after idling the engine for a few minutes.

·

When using a belt tension gauge, confirm the accuracy first by using a master gauge.

·

When reinstalling a belt used for over 5 minutes, perform the check based on the used deflection value.

·

When checking a belt used for over 5 minutes, confirm the deflection value is within the specified range.




Hide 88310A 2.INSPECT NO. 1 V BELT (w/ Air Conditioning System)

a.
A329279C01
1.177,0.198 1.49,0.354 0.313,0.156 10 false *a 2.115,0.188 2.427,0.344 0.313,0.156 10 false *b 0.521,0.875 0.833,1.031 0.313,0.156 10 false *c
*a CORRECT
*b INCORRECT
*c Clearance


Visually check the No. 1 V belt for cracks, oiliness or wear.

Check that the No. 1 V belt does not touch the bottom of the pulley groove.

If necessary, replace the No. 1 V belt.


b.
A329280C01
1.365,0.625 1.677,0.781 0.313,0.156 10 false *1 1.854,0.469 2.167,0.625 0.313,0.156 10 false *2 1.865,1.406 2.177,1.563 0.313,0.156 10 false *3
*1 Cooler Compressor Assembly
*2 Cooler Compressor Idle Pulley
*3 Crankshaft Pulley


Check the No. 1 V belt deflection by pressing on the No. 1 V belt at the points indicated in the illustration with 98 N (10 kgf, 22.0 lbf) of force.

Standard Deflection:
Item Specified Condition
New belt 12.0 to 16.0 mm (0.472 to 0.630 in.)
Used belt 16.0 to 22.0 mm (0.630 to 0.866 in.)


If the deflection is not as specified, adjust it.


c.
A329277C01
0.427,1.344 0.594,1.344 0.594,1.344 0.823,1.552 false 2.313,0.573 2.542,0.385 2.542,0.385 2.729,0.385 false 0.25,1.271 0.552,1.469 0.302,0.198 10 false *a 2.781,0.313 3.094,0.469 0.313,0.156 10 false *b
*a Belt Tension Gauge
*b Belt Tension Gauge Cable


Reference:

Using belt tension gauge and belt tension gauge cable, measure the No. 1 V belt tension.

Standard Tension:
Item Specified Condition
New belt 441 to 539 N (45 to 55 kgf)
Used belt 196 to 343 N (20 to 35 kgf)


If the belt tension is not as specified, adjust it.

NOTICE:
·

Check the No. 1 V belt tension at the specified point.

·

When installing a new No. 1 V belt, set its deflection value as specified.

·

Perform the No. 1 V belt tension and deflection value check after idling the engine for a few minutes.

·

When using a belt tension gauge, confirm the accuracy first by using a master gauge.

·

When reinstalling a belt used for over 5 minutes, perform the check based on the used deflection value.

·

When checking a belt used for over 5 minutes, confirm the deflection value is within the specified range.