Home › Engine / Hybrid System › 1VD-FTV (LUBRICATION) › OIL AND OIL FILTER › 2014.08–2016.08
RM25T0E _51 Engine / Hybrid System _029356 1VD-FTV LUBRICATION _0133489 OIL AND OIL FILTER A

1VD-FTV LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.

·

In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.



PROCEDURE

Hide 1.DRAIN ENGINE OIL

a.

Remove the oil filler cap.


b.

Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.


c.

Install a new gasket and the oil pan drain plug.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 2.REMOVE OIL FILTER ELEMENT

A161951E01
2.868,0.451 3.191,0.638 0.323,0.186 10 SST 2.34,0.83 2.638,0.536 2.638,0.536 2.826,0.536 false

a.

Using SST, remove the oil filter cap.

SST
09228-06501  

HINT:

Use a container to catch the draining oil. After the oil filter cap is loosened approximately 4 turns and the oil filter cap ribs are vertical, engine oil drains from the gap between the oil filter cap and oil pan sub-assembly.



b.
A106167C01
0.677,0.51 1.104,0.51 false 2.896,1.573 2.896,1.323 2.896,1.323 2.406,1.177 false 0.469,0.438 0.688,0.656 0.219,0.219 10 false *1 2.823,1.604 3.135,1.76 0.313,0.156 10 false *2
*1 Oil Filter Element
*2 O-Ring


Remove the oil filter element and O-ring from the oil filter cap.

NOTICE:

Do not use any tools to remove the O-ring in order to prevent the cap from being damaged. Be sure to remove it by hand.



Hide 3.INSTALL OIL FILTER ELEMENT

A268595C23
1.521,1.042 1.594,0.802 1.594,0.802 1.667,0.802 false 3.094,1.156 3.177,0.906 3.177,0.906 3.25,0.906 false 1.667,0.719 1.906,0.875 0.24,0.156 10 *1 3.25,0.813 3.427,0.979 0.177,0.167 10 *1 0.875,1.781 1.135,1.948 0.26,0.167 10 *a 2.438,1.781 2.667,1.948 0.229,0.167 10 *b
*1 O-Ring
*a CORRECT
*b INCORRECT


a.

Clean the inside of the oil filter cap, its threads and its O-ring groove.


b.

Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.

NOTICE:
·

Be sure to install the O-ring in the proper location, otherwise oil may leak.

·

Do not twist the O-ring.




c.

Set a new oil filter element in the oil filter cap.


d.

Remove any dirt or foreign matter from the installation surface of the engine.


e.

Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.


f.
A331184C01
0.844,2.917 0.979,2.917 0.979,2.917 1.115,2.615 false 1.313,2.979 1.427,2.979 1.427,2.979 1.625,2.531 true 2.021,2.469 2.094,2.677 2.094,2.677 2.219,2.677 false 2.438,0.844 2.656,0.604 2.656,0.604 2.865,0.604 false 2.271,2.604 2.552,2.875 0.281,0.271 10 false *1 1.135,2.906 1.448,3.063 0.313,0.156 10 false *2 0.667,2.854 0.938,3.042 0.271,0.188 10 false *3 1.802,3.021 2.115,3.177 0.313,0.156 10 false *a 2.917,0.542 3.344,0.76 0.427,0.219 10 false SST
*1 Oil Filter Cap
*2 O-Ring
*3 Oil Filter Bracket
*a No Gap


Using SST, tighten the oil filter cap.

SST
09228-06501  

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:

After tightening the oil filter cap, make sure that there is no gap and that the O-ring is not protruding.



Hide 4.ADD ENGINE OIL

a.

Add fresh engine oil and install the oil filler cap.

Standard Engine Oil:
Oil Grade Oil Viscosity (SAE)
API CF-4, CF or ACEA B1
(You may also use API CE or CD)
- 5W-30
- 10W-30
- 15W-40
- 20W-50
(5W-30 is best choice for fuel economy and good starting in cold weather.)


Standard Capacity:
Item Specified Condition
Drain and refill without oil filter change 8.5 liters (9.0 US qts, 7.5 Imp. qts)
Drain and refill with oil filter change 9.4 liters (9.9 US qts, 8.3 Imp. qts)
Dry fill 10.5 liters (11.1 US qts, 9.2 Imp. qts)



Hide 5.INSPECT FOR OIL LEAK

a.

Start the engine. Make sure that there are no oil leaks from the areas that were worked on.