Home › Engine / Hybrid System › 1GR-FE (STARTING) › STARTER
RM25T0E _51 Engine / Hybrid System _029357 1GR-FE STARTING _0133495 STARTER A

1GR-FE STARTING  STARTER  REASSEMBLY  


PROCEDURE

Hide 28160 1.INSTALL STARTER ARMATURE ASSEMBLY

a.
A331257C01
0.396,1.677 0.552,1.875 0.156,0.198 10 false -
V100135

High-Temperature Grease


Apply a light coat of high-temperature grease to the starter armature assembly as indicated by the arrow shown in the illustration, and then install the starter armature assembly to the starter yoke assembly.


Hide 28140 2.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.

Install the starter brush holder assembly.


b.
A215926

Connect the 4 brushes to the starter brush holder assembly.

i.

Using a screwdriver, hold back the brush spring.


ii.

Connect the brush to the brush holder.

NOTICE:

Check that positive (+) lead wires are not grounded.




c.
A173943C03
1.948,0.646 1.698,0.396 1.698,0.396 1.49,0.396 false 1.302,0.333 1.542,0.49 0.24,0.156 10 false *1
*1 O-Ring


Install a new O-ring in position on the starter yoke assembly.


d.

Install the starter commutator end frame to the starter yoke assembly with the 2 screws.

Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)


Hide 28150 3.INSTALL MAGNET STARTER SWITCH ASSEMBLY

a.

Apply high-temperature grease to the idle gear, steel ball, return spring, clutch roller and retainer.


b.
A222255

Insert the steel ball into the starter clutch sub-assembly hole.


c.

Insert the return spring to the starter clutch sub-assembly hole.


d.

Install the starter clutch sub-assembly, idle gear, retainer and clutch roller to the starter drive housing assembly.

A331259C01
4.521,1 4.896,0.74 4.896,0.74 5.125,0.74 false 3.542,2.458 3.344,2.458 3.344,2.458 3.094,2.01 false 3.156,0.813 3.396,0.427 3.396,0.427 3.573,0.427 false 2.854,1.104 3.052,1.292 3.052,1.292 3.208,1.292 false 1.958,1.344 2.229,1.344 2.229,1.344 2.406,1.156 false 1.938,2.396 2.135,2.396 2.135,2.396 2.354,1.979 false 5.167,0.677 5.479,0.833 0.313,0.156 10 false *1 3.583,2.396 3.896,2.552 0.313,0.156 10 false *2 3.615,0.365 3.927,0.521 0.313,0.156 10 false *3 3.25,1.229 3.563,1.385 0.313,0.156 10 false *4 1.781,1.281 2.094,1.438 0.313,0.156 10 false *5 1.76,2.333 2.073,2.49 0.313,0.156 10 false *6
*1 Starter Drive Housing Assembly *2 Starter Clutch Sub-assembly
*3 Idle Gear *4 Retainer
*5 Clutch Roller *6 Return Spring
V100135

High-Temperature Grease - -



e.

Install the magnet starter switch assembly to the starter drive housing assembly with the 2 screws.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)


Hide 28120 4.INSTALL STARTER YOKE ASSEMBLY

a.

Install a new O-ring to the groove of the starter yoke assembly.


b.
A218208C02
2.135,1.219 2.438,0.802 2.438,0.802 2.615,0.802 true 1.167,0.802 0.948,0.677 0.948,0.677 0.729,0.677 true 0.542,0.604 0.771,0.792 0.229,0.188 10 false *a 2.656,0.74 2.969,0.896 0.313,0.156 10 false *b
*a Groove
*b Claw


Align the claw of the starter yoke assembly with the groove of the magnet starter switch assembly.


c.

Install the starter yoke assembly and starter commutator end frame together with the starter armature assembly to the magnet starter switch assembly with the 2 bolts.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)


d.

Connect the lead wire to terminal C with the nut.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)