Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM25T0E _58 Vehicle Interior _029469 HEATING / AIR CONDITIONING _0133768 AIR CONDITIONING SYSTEM U

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  TERMINALS OF ECU  


CHECK COOLER STABILIZER AMPLIFIER ASSEMBLY (for 1HZ)


E140270N01
3.469,0.323 3.896,0.552 0.427,0.229 3.563,0.354 3.896,0.521 0.333,0.167 10 false I11

a.

Measure the voltage according to the value(s) in the table below.

HINT:

Check from the rear of the connector while it is connected to the cooler stabilizer amplifier assembly.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I11-3 (PSW) - I11-16(GND) R-B - W-B Pressure switch signal Ignition switch ON
Blower switch ON
Refrigerant pressure: Normal pressure (less than 3.14 MPa [32.0 kgf/cm2, 455 psi] and more than 0.196 MPa [2.0 kgf/cm2, 28 psi])
11 to 14 V
Ignition switch ON
Blower switch ON
Refrigerant pressure: Abnormal pressure (less than 0.196 MPa [2.0 kgf/cm2, 28 psi] or more than 3.14 MPa [32.0 kgf/cm2, 455 psi])
Below 1 V
I11-11 (B) - I11-16 (GND) L-R - W-B Ignition power supply Ignition switch ON
Blower switch ON
11 to 14 V
Ignition switch off Below 1 V
I11-16 (GND) - Body ground W-B - Body ground Ground for main power supply Always Below 1 V
I11-20 (MGC) - I11-16 (GND) L - W-B Magnet clutch assembly operation signal Ignition switch ON
Blower switch ON
A/C switch OFF
Magnet clutch relay is not engaged
11 to 14 V
Ignition switch ON
Blower switch ON
A/C switch ON
Magnet clutch relay is engaged
Below 1 V
I11-15 (SG) - Body ground B-L - Body ground Ground for No. 1 cooler thermistor (evaporator temperature sensor) Always Below 1 V
I11-7 (TE) - I11-15 (SG) Y-G - B-L No. 1 cooler thermistor (evaporator temperature sensor) signal Ignition switch ON
Blower switch ON
Evaporator temperature at 0°C (32°F)
Temperature control resistor MIN Cool
1.8 to 2.2 V
Ignition switch ON
Blower switch ON
Evaporator temperature at 15°C (59°F)
Temperature control resistor MIN Cool
1.0 to 1.4 V
I11-10 (ST) - I11-16 (GND) B-W - W-B Starter switch cut signal Engine start 11 to 14 V
I11-8 (B/V) - I11-7 (TE) Y-B - Y-G Temperature control resistor signal Ignition switch ON
Blower switch ON
Terminals between TE and SG connected
Temperature control resistor OFF
2.0 to 2.4 V
Ignition switch ON
Blower switch ON
Terminals between TE and SG connected
Temperature control resistor MAX Cool
Below 1 V
Ignition switch ON
Blower switch ON
Terminals between TE and SG connected
Temperature control resistor MIN Cool
1.0 to 1.4 V



CHECK COOLER STABILIZER AMPLIFIER ASSEMBLY (for 1VD-FTV and 1GR-FE)


E140271N02
3.469,0.354 3.885,0.573 0.417,0.219 3.583,0.385 3.896,0.573 0.313,0.188 10 false I12

a.

Measure the voltage according to the value(s) in the table below.

HINT:

Check from the rear of the connector while it is connected to the cooler stabilizer amplifier assembly.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I12-2 (PSW) - I12-5(GND) R-B - W-B Pressure switch signal Ignition switch ON
Blower switch ON
Refrigerant pressure: Normal pressure (less than 3.14 MPa [32.0 kgf/cm2, 455 psi] and more than 0.196 MPa [2.0 kgf/cm2, 28 psi])
11 to 14 V
Ignition switch ON
Blower switch ON
Refrigerant pressure: Abnormal pressure (less than 0.196 MPa [2.0 kgf/cm2, 28 psi] or more than 3.14 MPa [32.0 kgf/cm2, 455 psi])
Below 1 V
I12-7 (B) - I12-5 (GND) L-R - W-B Ignition power supply Ignition switch ON
Blower switch ON
11 to 14 V
Ignition switch off Below 1 V
I12-5 (GND) - Body ground W-B - Body ground Ground for main power supply Always Below 1 V
I12-11 (MGC) - I12-5 (GND) L - W-B Magnet clutch assembly operation signal Ignition switch ON
Blower switch ON
A/C switch OFF
Magnet clutch relay is not engaged
11 to 14 V
Ignition switch ON
Blower switch ON
A/C switch ON
Magnet clutch relay is engaged
Below 1 V
I12-6 (ACT) - I12-5 (GND) L-B - W-B Cooler compressor assembly on permit signal Ignition switch ON
A/C switch ON
Blower switch ON
Engine is running
Magnet clutch relay is not engaged
Below 1 V
I12-12 (SG) - Body ground W-G - Body ground Ground for No. 1 cooler thermistor (evaporator temperature sensor) Always Below 1 V
I12-3 (TE) - I12-12 (SG) Y-G - W-G No. 1 cooler thermistor (evaporator temperature sensor) signal Ignition switch ON
Blower switch ON
Evaporator temperature at 0°C (32°F)
Temperature control resistor MIN Cool
1.8 to 2.2 V
Ignition switch ON
Blower switch ON
Evaporator temperature at 15°C (59°F)
Temperature control resistor MIN Cool
1.0 to 1.4 V
I12-1 (AC1) - I12-5 (GND) B-W - W-B Idle-up request signal Ignition switch ON
Blower switch ON
Magnet clutch is not engaged
A/C switch OFF
11 to 14 V
Ignition switch ON
Blower switch ON
Magnet clutch is engaged
A/C switch ON
Below 1 V
I12-4 (IGN) - I12-5 (GND) B - W-B Engine speed signal Engine is running
Blower switch ON
Pulse generation
I12-10 (LOCK) - I12-12(SG) B-W - W-G Cooler compressor assembly lock sensor signal Engine is running
Blower switch ON
Magnet clutch is engaged
Pulse generation
I12-8 (B/V) - I12-3 (TE) Y-B - Y-G Temperature control resistor signal Ignition switch ON
Blower switch ON
Terminals between TE and SG connected
Temperature control resistor OFF
2.0 to 2.4 V
Ignition switch ON
Blower switch ON
Terminals between TE and SG connected
Temperature control resistor MAX Cool
Below 1 V
Ignition switch ON
Blower switch ON
Terminals between TE and SG connected
Temperature control resistor MIN Cool
1.0 to 1.4 V