Home › Power Source / Network › 1HZ (BATTERY / CHARGING) › GENERATOR
RM25T0E _57 Power Source / Network _029611 1HZ BATTERY / CHARGING _0134068 GENERATOR A

1HZ BATTERY / CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 27411 1.REMOVE GENERATOR PULLEY

a.

Mount the generator assembly in a vise between aluminum plates.


b.
A327040C01
2.5,1.469 2.5,1.302 2.5,1.302 2.917,0.75 true 3.135,1.333 3.135,0.667 true 1.729,1.885 1.958,2.042 0.229,0.156 10 false *a 2.854,1.344 3.406,1.49 0.552,0.146 10 false SST 1-A 2.25,1.49 2.802,1.635 0.552,0.146 10 true SST 1-B
*a Hold
V100135

Turn


Install SST 1-A to the generator pulley shaft.

SST
09820-63011  (09820-06010, 09820-06021)

HINT:
SST 1-A and B 09820-06010
SST 2 09820-06021



c.

Insert SST 1-B to SST 1-A.


d.

Hold SST 1-A with a torque wrench and turn SST 1-B clockwise with the specified torque.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)

NOTICE:

Make sure that SST is secured on the generator rotor shaft.



e.
A327041C01
2.708,0.76 2.542,0.427 2.542,0.427 2.375,0.427 false 1.948,0.344 2.385,0.542 0.438,0.198 10 false SST 2
V100135

Insert


Insert SST 2 and attach it to the generator pulley nut.


f.
A327042C01
1.563,1.531 1.76,1.75 0.198,0.219 10 true *a 2.146,1.698 2.458,1.854 0.313,0.156 10 false *b
*a Hold
*b Turn


To loosen the generator pulley nut, turn SST 1-A in the direction shown in the illustration.

NOTICE:

To prevent damage to the generator rotor shaft, do not loosen the generator pulley nut more than one-half turn.



g.

Remove SST 2 from the generator assembly.


h.
A327043C01
2.667,1.5 2.667,1.333 2.667,1.333 2.917,0.698 true 3.125,1.292 3.125,0.625 true 1.958,1.521 2.177,1.708 0.219,0.188 10 true *a 2.833,1.281 3.427,1.469 0.594,0.188 10 false SST 1-A 2.396,1.521 2.969,1.719 0.573,0.198 10 true SST 1-B
*a Hold
V100135

Turn


Turn SST 1-B in the direction shown in the illustration, and then remove SST 1-A and SST 1-B.


i.

Remove the generator pulley nut and generator pulley.


Hide 27039 2.REMOVE GENERATOR REAR END COVER

a.
A327038

Remove the nut and terminal insulator.


b.
A327039

Remove the bolt, 3 nuts, rectifier plate and generator rear end cover.


Hide 27370 3.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.

Remove the brush holder cover.


b.
A330267

Remove the 2 screws and generator brush holder assembly.


c.

Remove the plate seal.


Hide 27700A 4.REMOVE GENERATOR REGULATOR ASSEMBLY

a.
A330268

Remove the 3 screws and generator regulator assembly.


Hide 27357 5.REMOVE GENERATOR HOLDER WITH RECTIFIER

a.
A330269

Remove the 4 screws and generator holder with rectifier.


b.

Remove the 4 rubber insulators.


Hide 6.REMOVE GENERATOR RECTIFIER END FRAME

a.
A330270

Remove the 4 nuts and cord clip.


b.
A330271

Using SST, remove the generator rectifier end frame.

SST
09286-46011  


c.

Remove the generator washer from the generator rotor assembly.


Hide 27330 7.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A330272N01
1.802,0.917 2.333,0.25 2.333,0.25 1.802,0.417 false 2.375,0.135 2.833,0.333 0.458,0.198 10 false SST

Using SST and press, press out the generator rotor assembly.

SST
09950-60010  (09951-00180)
09950-70010  (09951-07100)