Home › Power Source / Network › 1VD-FTV (BATTERY / CHARGING) › GENERATOR
RM25T0E _57 Power Source / Network _029610 1VD-FTV BATTERY / CHARGING _0134070 GENERATOR A

1VD-FTV BATTERY / CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 27411 1.REMOVE GENERATOR PULLEY

a.

Mount the generator assembly in a vise between aluminum plates.


b.
A325936C01
3.063,1.156 3.063,0.635 true 2.5,1.51 2.5,1.219 2.5,1.219 2.938,0.74 true 1.729,1.854 2.042,2.01 0.313,0.156 10 false *a 2.219,1.531 2.969,1.729 0.75,0.198 10 true SST 1-B 2.792,1.177 3.396,1.354 0.604,0.177 10 true SST 1-A
*a Hold
V100135

Turn


Install SST 1-A to the generator pulley shaft.

SST
09820-63011  (09820-06010, 09820-06021)

HINT:
SST 1-A and 1-B 09820-06010
SST 2 09820-06021



c.

Insert SST 1-B to SST 1-A.


d.

Hold SST 1-A with a torque wrench and turn SST 1-B clockwise to the specified torque.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)

NOTICE:

Make sure that SST is secured to the generator rotor shaft.



e.
A325937C01
2.74,0.865 2.583,0.344 2.583,0.344 2.417,0.344 true 2,0.26 2.771,0.458 0.771,0.198 10 false SST 2
V100135

Insert


Insert SST 2 and attach it to the generator pulley nut.


f.
A325938C01
1.823,1.688 2.052,1.896 0.229,0.208 10 true *a
*a Hold
V100135

Turn


To loosen the generator pulley nut, turn SST 1-A in the direction shown in the illustration.

NOTICE:

To prevent damage to the generator rotor shaft, do not loosen the generator pulley nut more than one-half turn.



g.

Remove SST 2 from the generator assembly.


h.
A325939C01
3.094,1.177 3.094,0.667 true 2.542,1.552 2.542,1.396 2.542,1.396 2.979,0.771 true 1.99,1.615 2.198,1.76 0.208,0.146 10 true *a 2.302,1.573 2.948,1.792 0.646,0.219 10 true SST 1-B 2.802,1.198 3.417,1.406 0.615,0.208 10 false SST 1-A
*a Hold
V100135

Turn


Turn SST 1-B in the direction shown in the illustration and remove SST 1-A and 1-B.


i.

Remove the generator pulley nut and generator pulley.


Hide 27039 2.REMOVE GENERATOR REAR END COVER

a.
A163100

Place the generator assembly on the generator pulley.


b.

Remove the 3 nuts and generator rear end cover.


Hide 27387 3.REMOVE TERMINAL INSULATOR

A326125

a.

Remove terminal insulator from the generator assembly.


Hide 27370 4.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A156428

Remove the 2 screws and generator brush holder assembly.


Hide 27360 5.REMOVE GENERATOR COIL ASSEMBLY

a.
A156433

Remove the 4 bolts.


b.
A326126C01
0.667,0.167 0.917,0.167 0.917,0.167 1.115,0.333 false 0.25,0.51 0.51,0.667 0.26,0.156 10 false *a 0.375,0.083 0.76,0.281 0.385,0.198 10 false SST
*a Hold
V100135

Turn


Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)


Hide 27330 6.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A156421

Remove the generator washer.


b.
A230487

Remove the generator rotor assembly.


Hide 27310B 7.INSPECT GENERATOR DRIVE END FRAME BEARING

a.
A163021

Check that the generator drive end frame bearing is not rough or worn.

If necessary, replace the generator drive end frame bearing.


Hide 27310B 8.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A163022

Remove the 4 screws and retainer plate.


b.
A163023N01
1.677,0.802 2.656,1.115 2.656,1.115 1.802,1.156 true 2.698,1.021 3.021,1.188 0.323,0.167 10 false SST

Using SST and a hammer, tap out the generator drive end frame bearing.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)