Home › Power Source / Network › 1VD-FTV (BATTERY / CHARGING) › GENERATOR
RM25T0E _57 Power Source / Network _029610 1VD-FTV BATTERY / CHARGING _0134070 GENERATOR A

1VD-FTV BATTERY / CHARGING  GENERATOR  REASSEMBLY  


PROCEDURE

Hide 27310B 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A163024N01
1.885,0.635 2.917,0.531 2.917,0.531 2.031,1.042 true 2.969,0.448 3.281,0.635 0.313,0.188 10 false SST

Using SST and a press, press in a new generator drive end frame bearing.

SST
09950-60010  (09951-00470)
09950-70010  (09951-07100)


b.

Install the retainer plate with the 4 screws.

Torque:
2.3 N*m (23 kgf*cm, 20 in.*lbf)


Hide 27330 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.
A163025

Place the drive end frame on the generator pulley.


b.

Install the generator rotor assembly to the generator drive end frame.


c.
A163026

Place the new generator washer on the generator rotor assembly.


Hide 27360 3.INSTALL GENERATOR COIL ASSEMBLY

a.
B016512N01
1.75,0.5 2.323,0.229 2.323,0.229 2.531,0.229 true 2.604,0.146 3.063,0.344 0.458,0.198 10 false SST

Using SST and a press, slowly press in the generator coil assembly.

SST
09285-76010  


b.

Install the generator coil assembly with the 4 bolts.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)


Hide 27370 4.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A163028C01
0.729,0.667 0.927,0.313 0.927,0.313 1.063,0.313 true 1.115,0.219 1.427,0.375 0.313,0.156 10 false *a
*a Pin


While pushing the 2 brushes toward the inside of the generator brush holder assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the brush holder hole.


b.
A163029C01
2.01,0.823 2.615,0.281 2.615,0.281 2.792,0.281 true 2.833,0.188 3.146,0.344 0.313,0.156 10 false *a
*a Pin


Install the generator brush holder assembly with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


c.

Pull out the pin from the generator brush holder assembly.


Hide 27387 5.INSTALL TERMINAL INSULATOR

a.

Install the terminal insulator to the generator assembly.

NOTICE:

Pay attention to the mounting orientation of the terminal insulator.



Hide 27039 6.INSTALL GENERATOR REAR END COVER

a.
A156426

Install the generator rear end cover with the 3 nuts.

Torque:
4.6 N*m (47 kgf*cm, 41 in.*lbf)


Hide 27411 7.INSTALL GENERATOR PULLEY

a.

Temporarily install the generator pulley with the generator pulley nut by hand.


b.
A325936C01
3.063,1.156 3.063,0.635 true 2.5,1.51 2.5,1.219 2.5,1.219 2.938,0.74 true 1.729,1.854 2.042,2.01 0.313,0.156 10 false *a 2.219,1.531 2.969,1.729 0.75,0.198 10 true SST 1-B 2.792,1.177 3.396,1.354 0.604,0.177 10 true SST 1-A
*a Hold
V100135

Turn


Mount the generator assembly in a vise between aluminum plates.


c.

Install SST 1-A to the generator pulley shaft.

SST
09820-63011  (09820-06010, 09820-06021)

HINT:
SST 1-A and 1-B 09820-06010
SST 2 09820-06021



d.

Install SST 1-B to SST 1-A.


e.

Hold SST 1-A with a torque wrench, and turn SST 1-B clockwise to the specified torque.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)

NOTICE:

Make sure that SST is secured to the generator rotor shaft.



f.
A325937C01
2.74,0.865 2.583,0.344 2.583,0.344 2.417,0.344 true 2,0.26 2.771,0.458 0.771,0.198 10 false SST 2
V100135

Insert


Insert SST 2 and attach it to the generator pulley nut.


g.
A326254C01
1.844,1.719 2.031,1.906 0.188,0.188 10 true *a
*a Hold
V100135

Turn


Tighten the generator pulley nut by turning SST 1-A in the direction shown in the illustration.

Torque:
132.5 N*m (1351 kgf*cm, 98 ft.*lbf)


h.

Remove SST 2 from the generator assembly.


i.
A325939C01
3.094,1.177 3.094,0.667 true 2.542,1.552 2.542,1.396 2.542,1.396 2.979,0.771 true 1.99,1.615 2.198,1.76 0.208,0.146 10 true *a 2.302,1.573 2.948,1.792 0.646,0.219 10 true SST 1-B 2.802,1.198 3.417,1.406 0.615,0.208 10 false SST 1-A
*a Hold
V100135

Turn


Turn SST 1-B in the direction shown in the illustration and remove SST 1-A and 1-B.


j.

Turn the generator pulley and check that the generator pulley moves smoothly.