Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › THROTTLE BODY
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135331 THROTTLE BODY G

1GR-FE ENGINE CONTROL  THROTTLE BODY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 22030 1.CHECK THROTTLE BODY WITH MOTOR ASSEMBLY

a.

Before cleaning, or after cleaning the throttle body with motor assembly and installing it to the vehicle, turn the ignition switch to ON without operating the accelerator pedal sensor assembly.

NOTICE:

If the accelerator pedal sensor assembly has been operated, restart the procedure from the step above.



b.

Connect the GTS to the DLC3 and check for DTCs. If DTCs are stored, repair them by following the repair procedure flow. If DTCs are not stored, perform the throttle body operation check.


c.

Check throttle body operation.

i.

Enter the following menus:

Powertrain / Engine and ECT / Active Test / Control the ETCS Open/Close Slow Speed


ii.

During Active Test operation, check the Data List items "Throttle Position Command" and "Throttle Position No.1".

Powertrain > Engine and ECT > Active Test
Active Test Display
Control the ETCS Open/Close Slow Speed
Data List Display
Throttle Position No.1
Throttle Position Command
50004 234 39 282,277
A451720C06
2.333,1.698 2.531,1.698 false 1.781,1.198 1.969,1.198 false 5.646,1.594 5.823,1.594 false 6.208,1.083 6.375,1.083 false 2.042,4.99 2.417,4.99 true 3.25,3.927 3.719,3.927 true 2.813,3.385 3.125,3.385 true 6,5.375 6.354,5.375 true 5.438,3.719 5.729,3.719 true 3.125,5.5 3.333,5.5 false 4.667,3.417 4.948,3.417 true 4.667,4.875 4.958,4.875 true 0.365,2.729 0.677,2.885 0.313,0.156 10 false *a 0.365,4.292 0.677,4.448 0.313,0.156 10 false *b 1.625,1.094 1.938,1.25 0.313,0.156 10 false *c 2.563,1.604 2.875,1.76 0.313,0.156 10 false *d 2.031,1.333 2.344,1.49 0.313,0.156 10 false *e 3.146,3.448 3.458,3.604 0.313,0.156 10 false *f 6.396,0.979 6.708,1.135 0.313,0.156 10 false *d 5.49,1.5 5.802,1.656 0.313,0.156 10 false *c 5.927,1.219 6.24,1.375 0.313,0.156 10 false *e 2.656,3.281 2.969,3.438 0.313,0.156 10 false *c 3.74,3.844 4.052,4 0.313,0.156 10 true *d 1.875,4.896 2.188,5.052 0.313,0.156 10 false *c 6.385,5.292 6.698,5.448 0.313,0.156 10 false *d 5.135,3.354 5.448,3.51 0.313,0.156 10 false *f 5.771,3.625 6.083,3.781 0.313,0.156 10 false *d 3.365,5.406 3.677,5.563 0.313,0.156 10 false *d 4.521,3.323 4.833,3.479 0.313,0.156 10 false *c 2.729,4.99 3.042,5.146 0.313,0.156 10 false *f 5.344,5.01 5.656,5.167 0.313,0.156 10 false *f 4.51,4.792 4.823,4.948 0.313,0.156 10 false *c 0.021,2.219 0.49,2.5 0.469,0.281 10 false 1.3V 0.021,0.563 0.5,0.833 0.479,0.271 10 false 2.1V 0.021,2.854 0.594,3.177 0.573,0.323 10 false 2.1V 0.031,4.052 0.656,4.396 0.625,0.344 10 false 1.3V 0.031,4.396 0.51,4.698 0.479,0.302 10 false 2.1V 0.031,5.594 0.552,5.813 0.521,0.219 10 false 1.3V
*a Correct *b Incorrect
*c Throttle Position Command *d Throttle Position No.1
*e Specified Condition *f 200 ms


OK:
Tester Display Condition Specified Condition
Throttle Position Command
Throttle Position No.1
Checked during Active Test operation at a voltage of 1.3 V to 2.1 V. Response lag between Throttle Position Command and Throttle Position No.1 is within 200 ms.



iii.

Enter the following menus:

Powertrain / Engine and ECT / Active Test / Control the ETCS Open/Close Fast Speed


iv.

During Active Test operation, check the Data List items "Throttle Position Command" and "Throttle Position No.1".

Powertrain > Engine and ECT > Active Test
Active Test Display
Control the ETCS Open/Close Fast Speed
Data List Display
Throttle Position No.1
Throttle Position Command
50004 234 40 282,277
A451719C05
2.333,1.698 2.531,1.698 false 1.802,1.198 1.969,1.198 false 5.656,1.594 5.823,1.594 false 6.198,1.083 6.365,1.083 false 3.208,3.948 3.615,3.948 true 2.781,3.313 3.156,3.313 true 4.604,3.281 4.896,3.281 true 5.406,3.896 5.719,3.896 true 2.125,4.938 2.417,4.938 true 3.115,5.469 3.323,5.469 true 4.615,4.823 4.906,4.823 true 5.948,5.406 6.26,5.406 true 0.344,2.771 0.656,2.927 0.313,0.156 10 false *a 0.313,4.313 0.625,4.469 0.313,0.156 10 false *b 1.646,1.104 1.958,1.26 0.313,0.156 10 false *c 2.563,1.594 2.875,1.75 0.313,0.156 10 false *d 2.021,1.354 2.333,1.51 0.313,0.156 10 false *e 6.396,0.979 6.708,1.135 0.313,0.156 10 false *d 5.5,1.5 5.813,1.656 0.313,0.156 10 false *c 5.927,1.229 6.156,1.427 0.229,0.198 10 false *e 2.625,3.219 2.938,3.375 0.313,0.156 10 false *c 3.344,5.385 3.604,5.563 0.26,0.177 10 false *d 4.458,4.74 4.771,4.896 0.313,0.156 10 false *c 6.292,5.323 6.604,5.479 0.313,0.156 10 false *d 3.083,3.521 3.354,3.708 0.271,0.188 10 false *f 3.635,3.865 3.948,4.021 0.313,0.156 10 false *d 4.427,3.198 4.74,3.354 0.313,0.156 10 false *c 5.063,3.396 5.375,3.552 0.313,0.156 10 false *f 5.729,3.813 6.042,3.969 0.313,0.156 10 false *d 1.969,4.844 2.281,5 0.313,0.156 10 false *c 2.698,5.052 2.969,5.24 0.271,0.188 10 false *f 5.292,5.073 5.604,5.229 0.313,0.156 10 false *f 0,0.573 0.708,0.896 0.708,0.323 10 false 2.1V 0,2.198 0.625,2.49 0.625,0.292 10 false 1.3V 0.021,2.875 0.76,3.333 0.74,0.458 10 false 2.1V 0.021,4.094 0.573,4.354 0.552,0.26 10 false 1.3V 0,4.427 0.583,4.74 0.583,0.313 10 false 2.1V 0,5.646 0.5,5.823 0.5,0.177 10 false 1.3V
*a Correct *b Incorrect
*c Throttle Position Command *d Throttle Position No.1
*e Specified Condition *f 200 ms


OK:
Tester Display Condition Specified Condition
Throttle Position Command
Throttle Position No.1
Checked during Active Test operation at a voltage of 1.3 V to 2.1 V. Response lag between Throttle Position Command and Throttle Position No.1 is within 200 ms.




d.

Warm up the engine.

NOTICE:
·

The A/C switch and all accessory switches should be off.

·

The electric fan should be off.

·

After warming up the engine, check that the coolant temperature is 75 °C (167 °F) or more.




e.

Check the "Throttle Sensor Volt %".

i.

Read the Data List while quickly and fully depressing the accelerator pedal and check that the value for "Throttle Sensor Volt %" is 60% or more.



f.

If there was any abnormality found during the throttle body operation check or "Throttle Sensor Volt %" check, clean the throttle body, then reassemble it and perform the throttle body operation check again. If the operation returns to normal, the procedure is complete. If operation does not return to normal, replace the throttle body with motor assembly.