Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, current flows from terminal ST1 of the ignition switch to terminal STA of the ECM (STA Signal).

WIRING DIAGRAM

A333594E02
6.188,1.906 6.646,2.104 0.458,0.198 10 false STA 6.354,2.823 6.813,3.021 0.458,0.198 10 false ECM 5.833,1.906 6.292,2.104 0.458,0.198 10 false A29 5.521,1.917 5.979,2.115 0.458,0.198 10 false I84 5.49,1.729 6.271,1.917 0.781,0.188 10 false 48*1 48*2 4.75,1.104 5.063,1.302 0.313,0.198 10 false ST 3.396,2.667 3.708,2.865 0.313,0.198 10 false ST 4.104,0.281 4.26,0.479 0.156,0.198 10 false 3 3.042,0.281 3.198,0.479 0.156,0.198 10 false 4 3.823,0.531 4.281,0.729 0.458,0.198 10 false ST1 3.271,0.51 3.729,0.708 0.458,0.198 10 false AM1 3.26,0.906 3.719,1.104 0.458,0.198 10 false L21 3.25,1.073 5.542,1.271 2.292,0.198 10 false Ignition Switch 1.458,0.604 1.917,0.802 0.458,0.198 10 false AM1 0.615,1.094 1.073,1.292 0.458,0.198 10 false ALT 3.208,2.26 3.365,2.458 0.156,0.198 10 false 1 2.552,2.24 2.708,2.438 0.156,0.198 10 false 5 3.24,3.083 3.396,3.281 0.156,0.198 10 false 2 2.531,3.083 2.688,3.281 0.156,0.198 10 false 3 2.625,3.719 2.938,3.917 0.313,0.198 10 false D2 1.604,4.354 1.917,4.552 0.313,0.198 10 false D3 2.177,4.833 3.25,5.031 1.073,0.198 10 false Starter 0.76,4.948 1.833,5.146 1.073,0.198 10 false Battery 0.594,2.844 1.667,3.042 1.073,0.198 10 false FL MAIN 1.469,2.083 1.927,2.281 0.458,0.198 10 false AM2 2.99,3.688 3.146,3.885 0.156,0.198 10 false 1 1.604,4.125 1.76,4.323 0.156,0.198 10 false 1 5.333,5.042 6.406,5.24 1.073,0.198 10 false *2: LHD 5.302,4.688 6.375,4.885 1.073,0.198 10 false *1: RHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

This diagnosis procedure is based on the premise that the engine can crank normally. If the engine cannot crank normally, proceed to the Problem Symptoms Table.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>PROBLEM SYMPTOMS TABLE


PROCEDURE

1.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.


Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B



A

2.READ VALUE USING GTS (STARTER SIGNAL)

B

9.READ VALUE USING GTS (STARTER SIGNAL)
2.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the GTS when the ignition switch is turned to ON and START.

OK:
Ignition Switch Position Starter Signal
On OFF
START ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK ST RELAY (POWER SOURCE)
3.CHECK ST RELAY (POWER SOURCE)
A222472C01
0.531,1.875 0.802,2.083 0.271,0.208 10 false *2 0.156,0.135 0.438,0.323 0.281,0.188 10 false *1
*1 Engine Room Relay Block Assembly
*2 ST


a.

Remove the ST relay from the Engine Room Relay Block Assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ST relay terminal 1 - Body ground Engine cranking 11 to 14 V


HINT:

The engine does not crank because the relay is not installed.



c.

Reinstall the ST relay.


Result:
Test Result Proceed to
OK A
NG (w/ Fuel Sub Tank) B
NG (w/o Fuel Sub Tank) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - IGNITION SWITCH)

B

4.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ST RELAY, SUB PMP RELAY)

C

7.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ST RELAY)
4.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ST RELAY, SUB PMP RELAY)
a.

Remove the ST relay from the Engine Room Relay Block Assembly Block.


b.

Remove the SUB PMP relay from the Engine Room Relay Block Assembly Block.


c.

Disconnect the ignition switch connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 1 - L21-3 (ST1) Always Below 1 Ω
ST relay terminal 1 or L21-3 (ST1) - Body ground Always 10 kΩ or higher
ST relay terminal 1 or SUB PMP relay terminal 1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT RELAY (SUB PMP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - IGNITION SWITCH)

5.INSPECT RELAY (SUB PMP)

Result:
Proceed to
OK
NG



OK

6.INSPECT IGNITION SWITCH

NG

REPAIR RELAY (SUB PMP)

6.INSPECT IGNITION SWITCH
a.
A222467C05
2.083,1.125 1.646,1.792 false 1.177,1.781 0.771,1.115 false 0.167,0.135 0.458,0.365 0.292,0.229 10 false *a 0.438,0.979 0.823,1.177 0.385,0.198 10 false AM1 2.188,0.979 2.604,1.198 0.417,0.219 10 false ST1
*a Component without harness connected
(Ignition Switch)


Disconnect the ignition switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (AM1) - 3 (ST1) Ignition switch position START Below 1 Ω
Except above 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - BATTERY)

NG

7.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ST RELAY)
a.

Remove the ST relay from the Engine Room Relay Block Assembly.


b.

Disconnect the ignition switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 1 - L21-3 (ST1) Always Below 1 Ω
ST relay terminal 1 or L21-3 (ST1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT IGNITION SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT IGNITION SWITCH
a.
A222467C05
2.083,1.125 1.646,1.792 false 1.177,1.781 0.771,1.115 false 0.167,0.135 0.458,0.365 0.292,0.229 10 false *a 0.438,0.979 0.823,1.177 0.385,0.198 10 false AM1 2.188,0.979 2.604,1.198 0.417,0.219 10 false ST1
*a Component without harness connected
(Ignition Switch)


Disconnect the ignition switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (AM1) - 3 (ST1) Ignition switch position START Below 1 Ω
Except above 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - BATTERY)

NG

9.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the GTS when the ignition switch is turned to ON and START.

OK:
Ignition Switch Position Starter Signal
On (IG) Close
START Open



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - ECM)