Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2014.08–2021.12
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0137  Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2)  P0157  Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2)  


DESCRIPTION

HINT:

Sensor 2 refers to the sensor mounted behind the three-way catalytic converter and located far from the engine assembly.


A three-way catalyst converter is used in order to convert the carbon monoxide, hydrocarbons, and nitrogen oxide, into less harmful substances. To allow the three-way catalytic converter to function effectively, it is necessary to keep the air fuel ratio of the engine near the stoichiometric air fuel ratio. For the purpose of helping the ECM to deliver accurate air fuel ratio control, a heated oxygen sensor is used.

The heated oxygen sensor is located behind the three-way catalytic converter, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).

When the air fuel ratio becomes lean, the oxygen concentration in the exhaust gas is rich. The heated oxygen sensor informs the ECM that the post-three way catalytic converter air fuel ratio is lean (low voltage, i.e. below 0.45 V).

Conversely, when the air fuel ratio is richer than the stoichiometric air fuel level, the oxygen concentration in the exhaust gas becomes lean. The heated oxygen sensor informs the ECM that the post-three way catalytic converter air fuel ratio is rich (high voltage, i.e. higher than 0.45 V). The heated oxygen sensor has the property of changing its output voltage drastically when the air fuel ratio is close to the stoichiometric level.

The ECM uses the supplementary information from the heated oxygen sensor to determine whether the air fuel ratio after the three-way catalytic converter is rich or lean, and adjusts the fuel injection time accordingly. Thus, if the heated oxygen sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air fuel ratio control.

A115539E03
2.981,1.232 3.287,0.841 false 2.687,1.79 3.304,1.79 false 2.596,2.418 3.255,2.383 false 2.677,2.697 3.258,2.832 false 1.093,2.916 1.331,2.916 false 1.452,0.775 2.460,0.977 1.009,0.202 10 Atmospheric Air 3.308,0.74 4.048,0.942 0.739,0.202 10 Housing 3.32,1.186 4.848,1.388 1.528,0.202 10 Platinum Electrode 3.955,0.89 4.920,1.092 0.964,0.202 10 Output Voltage 5.006,0.932 6.392,1.134 1.386,0.202 10 Ideal Air-fuel Mixture 2.007,3.13 2.907,3.332 0.899,0.202 10 Exhaust Gas 3.34,1.698 4.802,2.066 1.461,0.368 10 Solid Electrolyte (Zirconia Element) 3.294,2.757 4.497,2.959 1.203,0.202 10 Coating (Ceramic) 3.32,2.284 3.803,2.486 0.483,0.202 10 Heater 1.367,2.82 1.805,3.032 0.438,0.211 10 Cover 4.787,2.849 7.090,3.050 2.304,0.202 10 Richer - Air-fuel Ratio - Leaner 2.668,1.455 2.667,1.53 false 2.725,1.641 3.306,1.271 3.306,1.271 2.667,1.494 false

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0137 Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2) During active air fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a) The heated oxygen sensor voltage output is below 0.21 V.

(b) The target air fuel ratio is rich.


·

Heated oxygen sensor (bank 1 sensor 2) circuit

·

Heated oxygen sensor (bank 1 sensor 2)

·

Air fuel ratio sensor (bank 1 sensor 1)

·

Gas leak from exhaust system


Comes on DTC stored
P0157 Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2) During active air fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a) The heated oxygen sensor voltage output is below 0.21 V.

(b) The target air fuel ratio is rich.


·

Heated oxygen sensor (bank 2 sensor 2) circuit

·

Heated oxygen sensor (bank 2 sensor 2)

·

Air fuel ratio sensor (bank 2 sensor 1)

·

Gas leak from exhaust system


Comes on DTC stored

MONITOR DESCRIPTION

Active Air Fuel Ratio Control


The ECM usually performs air fuel ratio feedback control so that the Air Fuel Ratio (A/F) sensor output indicates a near stoichiometric air fuel level. This vehicle includes active air fuel ratio control in addition to regular air fuel ratio control. The ECM performs active air fuel ratio control to detect Heated Oxygen (HO2) sensor malfunctions.

Active air fuel ratio control is performed for approximately 15 to 20 seconds while driving with a warm engine. During active air fuel ratio control, the air fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, either of the following DTCs is stored: DTC P0137 or P0157 (open circuit).


Open in Heated Oxygen (HO2) Sensor Circuit


During active air fuel ratio control, the ECM calculates the Oxygen Storage Capacity (OSC)* of the Three-Way Catalytic Converter (TWC) by forcibly regulating the air fuel ratio to become rich or lean.

If the HO2 sensor has an open or short, or the voltage output of the sensor noticeably decreases, the OSC indicates an extraordinarily high value. Even if the ECM attempts to continue regulating the air fuel ratio to become rich or lean, the HO2 sensor output does not change.

While performing active air fuel ratio control, when the target air fuel ratio is rich and the HO2 sensor voltage output is 0.21 V or less (lean), the ECM interprets this as an abnormally low sensor output voltage and stores DTC P0137 or P0157.

HINT:

*: The TWC has the capability to store oxygen. When active air fuel ratio control is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If the rich-lean cycle of the HO2 sensor is long, the OSC becomes greater. There is a direct correlation between the OSCs of the HO2 sensor and the TWC.


A172862E01
0.111,0.07 4.501,0.279 4.390,0.209 10 HO2 SENSOR CIRCUIT LOW VOLTAGE (P0137 and P0157: OPEN) 0.79,1.561 1.682,1.900 0.892,0.339 10 Active air fuel ratio control 0.79,2.913 1.578,3.272 0.788,0.359 10 HO2 sensor voltage 0.79,2.206 2.059,2.408 1.269,0.202 10 Target air fuel ratio 2.481,2.031 3.434,2.399 0.953,0.368 10 Stoichiometric Air Fuel Level 3.184,1.684 3.440,1.886 0.256,0.202 10 Off 2.952,3.198 3.438,3.400 0.486,0.202 10 0.21 V 4.633,0.739 5.786,0.941 1.153,0.202 10 15 to 20 seconds 4.811,1.256 5.575,1.458 0.764,0.202 10 Operation 3.847,1.778 4.412,1.980 0.565,0.202 10 Normal 5.252,1.644 5.897,1.846 0.646,0.202 10 Abnormal 5.966,3.658 6.703,3.860 0.737,0.202 10 Abnormal 6.047,2.252 6.612,2.454 0.565,0.202 10 Normal 4.562,2.383 4.928,2.585 0.366,0.202 10 Rich 4.626,2.016 4.327,1.892 false 5.151,2.366 5.221,1.762 false 6.047,2.378 5.988,2.681 false 5.985,3.459 6.184,3.658 false


CONFIRMATION DRIVING PATTERN

HINT:
·

This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.

·

Performing this confirmation driving pattern will activate the heated oxygen sensor monitor (The catalyst monitor is performed simultaneously). This is very useful for verifying the completion of a repair.



A199376E80
1.988,2.392 2.229,2.573 0.241,0.182 10 [A] 2.597,2.086 2.808,2.275 0.211,0.188 10 [B] 3.942,0.642 4.158,0.830 0.216,0.188 10 [C] 4.996,3.303 5.219,3.496 0.223,0.193 10 [D] 0.379,0.436 1.595,0.620 1.216,0.184 10 100 km/h (63 mph) 0.434,1.305 1.562,1.489 1.128,0.184 10 60 km/h (37 mph) 1.186,2.123 1.585,2.288 0.399,0.165 10 Idling 0.366,2.372 1.535,2.531 1.170,0.160 10 Ignition Switch ON 2.312,2.859 3.120,3.043 0.809,0.184 10 Warming up 3.442,2.877 4.681,3.014 1.239,0.137 10 10 minutes or more

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

7.

With the shift lever in D, drive the vehicle at 60 to 120 km/h (37 to 75 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0137 or P0157.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again.




WIRING DIAGRAM

A331583E01
5.24,1.01 5.698,1.208 0.458,0.198 10 false I84 5.563,1 6.021,1.198 0.458,0.198 10 false A29 5.854,0.906 6.469,1.104 0.615,0.198 10 false MREL 5.104,0.844 5.417,1.042 0.313,0.198 10 false 44*2 5.469,0.844 5.781,1.042 0.313,0.198 10 false 44*3 2.271,1.281 2.729,1.479 0.458,0.198 10 false C18 2.281,1.448 5.052,1.802 2.771,0.354 10 false Heated Oxygen Sensor (Bank 1 Sensor 2) 5.563,1.865 6.021,2.063 0.458,0.198 10 false C39 5.563,2.292 6.021,2.49 0.458,0.198 10 false C39 5.563,2.823 6.021,3.021 0.458,0.198 10 false C39 5.563,4.125 6.021,4.323 0.458,0.198 10 false C39 5.552,4.552 6.01,4.75 0.458,0.198 10 false C39 5.563,5.094 6.021,5.292 0.458,0.198 10 false C39 5.604,1.688 5.917,1.885 0.313,0.198 10 false 48 5.594,2.125 5.906,2.323 0.313,0.198 10 false 88 5.604,2.656 5.917,2.854 0.313,0.198 10 false 65 5.594,3.948 5.906,4.146 0.313,0.198 10 false 47 5.594,4.385 5.906,4.583 0.313,0.198 10 false 87 5.594,4.906 5.906,5.104 0.313,0.198 10 false 64 5.865,1.719 6.479,1.917 0.615,0.198 10 false HT1B 5.875,2.281 6.49,2.479 0.615,0.198 10 false OX1B 5.885,2.802 6.5,3 0.615,0.198 10 false EX1B 5.885,4 6.5,4.198 0.615,0.198 10 false HT2B 5.875,4.542 6.49,4.74 0.615,0.198 10 false OX2B 5.885,5.083 6.5,5.281 0.615,0.198 10 false EX2B 2.677,3.406 3.135,3.604 0.458,0.198 10 false C17 2.833,3.583 4.323,3.969 1.49,0.385 10 false Heated Oxygen Sensor (Bank 2 Sensor 2) 4.667,2.667 4.979,2.865 0.313,0.198 10 false (*1) 4.844,4.917 5.458,5.115 0.615,0.198 10 false (*1) 3.865,1.75 4.021,1.948 0.156,0.198 10 false 1 3.865,2.156 4.021,2.354 0.156,0.198 10 false 3 2.99,1.75 3.146,1.948 0.156,0.198 10 false 2 2.969,2.177 3.125,2.375 0.156,0.198 10 false 4 3.458,1.75 3.948,1.958 0.49,0.208 10 false HT1B 3.146,1.75 3.458,1.948 0.313,0.198 10 false +B 3.146,2.177 3.458,2.375 0.313,0.198 10 false E2 3.448,2.135 4.063,2.333 0.615,0.198 10 false OX1B 3.865,4.021 4.021,4.219 0.156,0.198 10 false 1 2.99,4.031 3.188,4.229 0.198,0.198 10 false 2 3.865,4.406 4.021,4.604 0.156,0.198 10 false 3 2.99,4.427 3.146,4.625 0.156,0.198 10 false 4 3.448,4.01 4.063,4.208 0.615,0.198 10 false HT2B 3.146,4.01 3.458,4.208 0.313,0.198 10 false +B 3.448,4.375 4.063,4.573 0.615,0.198 10 false OX2B 3.146,4.365 3.458,4.563 0.313,0.198 10 false E2 0.802,2.417 1.083,2.646 0.281,0.229 10 false EFI 0.802,2.594 1.417,2.792 0.615,0.198 10 false NO.2 1.333,3.021 1.49,3.219 0.156,0.198 10 false 1 0.781,3.021 0.938,3.219 0.156,0.198 10 false 3 0.781,3.844 0.938,4.042 0.156,0.198 10 false 5 1.333,3.865 1.49,4.063 0.156,0.198 10 false 2 1.521,3.313 1.979,3.51 0.458,0.198 10 false EFI 1.531,3.49 2.146,3.688 0.615,0.198 10 false MAIN 0.802,4.354 1.26,4.552 0.458,0.198 10 false EFI 0.823,5.021 1.135,5.219 0.313,0.198 10 false FL 0.823,5.177 1.438,5.375 0.615,0.198 10 false MAIN 0.99,5.927 2.063,6.125 1.073,0.198 10 false Battery 4.885,5.906 6.719,6.104 1.833,0.198 10 false *1: Shielded 4.896,6.115 5.813,6.313 0.917,0.198 10 false *2: for LHD 4.896,6.323 5.813,6.521 0.917,0.198 10 false *3: for RHD 6.073,0.26 6.531,0.458 0.458,0.198 10 false ECM

CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the Air Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F sensor function using the GTS.

1.

Connect the GTS to the DLC3.

2.

Start the engine and turn the GTS on.

3.

Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

4.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.

5.

Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume.)

6.

Monitor the output voltages of the A/F and HO2 sensors (AFS Voltage B1S1 and O2S B1S2, or AFS Voltage B2S1 and O2S B2S2) displayed on the GTS.



HINT:
·

The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



GTS Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(A/F)
+25% Rich Less than 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(A/F)
-12.5% Lean More than 3.4 V
O2S B1S2 or O2S B2S2
(HO2)
+25% Rich More than 0.55 V
O2S B1S2 or O2S B2S2
(HO2)
-12.5% Lean Less than 0.4 V

NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


A283583E07
5.792,3.781 7.115,4.052 1.323,0.271 10 - Air fuel ratio sensor 3.823,4.927 4.531,5.104 0.708,0.177 8 Below 0.4 V 3.208,4.396 4.333,4.615 1.125,0.219 10 Output Voltage 3.25,3.365 4.542,3.615 1.292,0.25 10 Injection Volume 3.229,1.292 4.521,1.542 1.292,0.25 10 Injection Volume 3.24,2.313 4.333,2.521 1.094,0.208 10 Output Voltage 0.625,1.292 1.917,1.542 1.292,0.25 10 Injection Volume 0.625,3.365 1.917,3.615 1.292,0.25 10 Injection Volume 0.594,5.438 1.885,5.688 1.292,0.25 10 Injection Volume 0.604,7.49 1.896,7.74 1.292,0.25 10 Injection Volume 3.25,7.49 4.542,7.74 1.292,0.25 10 Injection Volume 3.25,5.438 4.542,5.688 1.292,0.25 10 Injection Volume 0.635,2.302 1.823,2.51 1.188,0.208 10 Output Voltage 0.625,4.396 1.792,4.646 1.167,0.25 10 Output Voltage 0.552,6.479 1.719,6.729 1.167,0.25 10 Output Voltage 0.573,8.563 1.74,8.813 1.167,0.25 10 Output Voltage 3.24,8.563 4.406,8.813 1.167,0.25 10 Output Voltage 3.25,6.479 4.417,6.729 1.167,0.25 10 Output Voltage 3.51,4.698 4.542,4.885 1.031,0.188 8 Higher than 0.55 V 0.927,2.646 1.958,2.833 1.031,0.188 8 Higher than 3.4 V 1.177,2.885 1.927,3.073 0.75,0.188 8 Below 3.1 V 1.531,1.594 1.979,1.781 0.448,0.188 8 12.5% 1.479,1.833 1.927,2.021 0.448,0.188 8 -12.5% 3.5,2.604 4.531,2.792 1.031,0.188 8 Higher than 0.55 V 3.813,2.844 4.521,3.021 0.708,0.177 8 Below 0.4 V 4.156,1.594 4.604,1.781 0.448,0.188 8 12.5% 4.115,1.833 4.563,2.021 0.448,0.188 8 -12.5% 4.146,3.729 4.594,3.917 0.448,0.188 8 12.5% 4.104,3.917 4.552,4.104 0.448,0.188 8 -12.5% 4.104,5.958 4.552,6.146 0.448,0.188 8 -12.5% 4.104,8.021 4.552,8.208 0.448,0.188 8 -12.5% 4.156,5.74 4.604,5.927 0.448,0.188 8 12.5% 4.156,7.813 4.604,8 0.448,0.188 8 12.5% 1.49,7.813 1.938,8 0.448,0.188 8 12.5% 1.49,5.75 1.938,5.938 0.448,0.188 8 12.5% 1.5,3.677 1.948,3.865 0.448,0.188 8 12.5% 1.448,3.896 1.896,4.083 0.448,0.188 8 -12.5% 1.448,5.948 1.896,6.135 0.448,0.188 8 -12.5% 1.438,8.021 1.885,8.208 0.448,0.188 8 -12.5% 0.844,4.802 2.042,5.052 1.198,0.25 8 Almost no reaction 0.854,8.938 2.052,9.188 1.198,0.25 8 Almost no reaction 3.5,8.938 4.698,9.188 1.198,0.25 8 Almost no reaction 3.49,6.865 4.688,7.115 1.198,0.25 8 Almost no reaction 0.917,6.771 1.948,6.958 1.031,0.188 8 Higher than 3.4 V 1.167,7.021 1.917,7.208 0.75,0.188 8 Below 3.1 V 0.24,2.083 0.396,2.281 0.156,0.198 10 1 0.24,4.25 0.396,4.448 0.156,0.198 10 2 0.25,6.333 0.406,6.531 0.156,0.198 10 3 0.24,8.417 0.396,8.615 0.156,0.198 10 4 0.125,0.688 0.573,0.938 0.448,0.25 10 Case 0.792,0.583 2.802,0.969 2.01,0.385 10 Air Fuel Ratio Sensor (Sensor 1) Output Voltage 3.5,0.583 5.594,1.031 2.094,0.448 10 Heated Oxygen Sensor (Sensor 2) Output Voltage 5.969,0.583 7.01,1 1.042,0.417 10 Main Suspected Trouble Area 6.396,2.115 6.552,2.313 0.156,0.198 10 - 5.802,4.031 7.125,4.469 1.323,0.438 10 - Air fuel ratio sensor heater 5.802,4.448 7.125,4.885 1.323,0.438 10 - Air fuel ratio sensor circuit 5.917,5.792 6.969,6.167 1.052,0.375 10 - Heated oxygen sensor 5.927,6.198 6.969,6.625 1.042,0.427 10 - Heated oxygen sensor heater 5.927,6.615 6.969,7.052 1.042,0.438 10 - Heated oxygen sensor circuit 5.927,7.698 6.813,8.104 0.885,0.406 10 - Fuel injector assembly 5.917,8.115 7.073,8.448 1.156,0.333 10 - Fuel pressure 5.917,8.365 6.969,9.375 1.052,1.01 10 - Gas leak from exhaust system (air fuel ratio extremely rich or lean) 2.552,2.75 3,2.938 0.448,0.188 8 OK 2.5,4.719 2.948,4.906 0.448,0.188 8 NG 2.552,6.865 3,7.052 0.448,0.188 8 OK 2.5,8.844 2.948,9.031 0.448,0.188 8 NG 5.167,2.708 5.615,2.896 0.448,0.188 8 OK 5.167,4.813 5.615,5 0.448,0.188 8 OK 5.135,8.854 5.583,9.042 0.448,0.188 8 NG 5.135,6.771 5.583,6.958 0.448,0.188 8 NG

·

Following the Control the Injection Volume for A/F sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.


HINT:
·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using an GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ OUTPUT DTC (DTC P0137 OR P0157)
a.

Connect an GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

d.

Read the DTCs.

Result:
Result Proceed to
DTC P0137 or P0157 is output A
DTC P0137 or P0157 and other DTCs are output B


HINT:

If any DTCs other than P0137 and P0157 are output, troubleshoot those DTCs first.




A

2.CHECK FOR EXHAUST GAS LEAK

B

2.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.



Result:
Proceed to
OK
NG



OK

3.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

3.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor (for bank 1 sensor 2) connector.


b.

Disconnect the heated oxygen sensor (for bank 2 sensor 2) connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C18-1 (HT1B) - C39-48 (HT1B) Always Below 1 Ω
C18-3 (OX1B) - C39-88 (OX1B) Always Below 1 Ω
C18-4 (E2) - C39-65 (EX1B) Always Below 1 Ω
C17-1 (HT2B) - C39-47 (HT2B) Always Below 1 Ω
C17-3 (OX2B) - C39-87 (OX2B) Always Below 1 Ω
C17-4 (E2) - C39-64 (EX2B) Always Below 1 Ω
C18-1 (HT1B) or C39-48 (HT1B) - Body ground Always 10 kΩ or higher
C18-3 (OX1B) or C39-88 (OX1B) - Body ground Always 10 kΩ or higher
C18-4 (E2) or C39-65 (EX1B) - Body ground Always 10 kΩ or higher
C17-1 (HT2B) or C39-47 (HT2B) - Body ground Always 10 kΩ or higher
C17-3 (OX2B) or C39-87 (OX2B) - Body ground Always 10 kΩ or higher
C17-4 (E2) or C39-64 (EX2B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE HEATED OXYGEN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE HEATED OXYGEN SENSOR

Result:
Proceed to
NEXT



NEXT

6.PERFORM CONFIRMATION DRIVING PATTERN
6.PERFORM CONFIRMATION DRIVING PATTERN
HINT:

Refer to the CONFIRMATION DRIVING PATTERN.


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158)
a.

Connect an GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

e.

Input DTCs: P0137 and P0157.


f.

Check the DTC MONITOR is "NORMAL." If DTC Monitoris "INCOMPLETE," perform the drive pattern adding thevehicle speed and using second gear to decelerate thevehicle.


Result:
Display (DTC Output) Proceed to
NORMAL
(No DTC output)
A
ABNORMAL
(P0137 or P0157 detected)
B



A

END

B